Abstract
Joint torque sensors are widely used in service robots for force control and collision detection. However, commercial torque sensors and amplifiers are too bulky to install inside robots. In this study, we propose an amplifier-embedded torque sensor because placing the amplifier away from the sensor tends to add noise to the output signal. Furthermore, joint torque sensors experience the torque ripple generated by the harmonic drive gear. Therefore, a torque ripple reduction method is also proposed in this study. FEM analysis was conducted to improve the sensitivity of the torque sensor to only torques in the direction of joint rotation. To avoid external noise and excessive wiring, an embedded amplifier, which can be installed inside the joint of the robot arm with the torque sensor, was developed. Also, the torque ripple reduction method based on the change in the installation position of Wheatstone bridges was developed. Through various experiments, the performance of the proposed torque sensor was verified.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Gravel, D. P. and Newman, W. S., “Flexible robotic assembly efforts at Ford Motor Company,” Proc. of the IEEE International Symposium on Intelligent Control, pp. 173–182, 2001.
Tsetserukou, D., Tadakuma, R., Kajimoto, H., Kawakami, N., and Tachi, S., “Development of a Whole-Sensitive Teleoperated Robot Arm using Torque Sensing Technique,” Proc. of the IEEE International Conference on Intelligent Robots and Systems, pp. 476–481, 2007.
Hirzinger, G., Sporer, N., Albu-Schaffer, A., Hahnle, M., Krenn, R., Pascucci, A., and Schedl, M., “DLR’s torque-controlled light weight robot III-are we reaching the technological limits now?” Proc. of the IEEE International Conference on Robotics and Automation, pp. 1710–1716, 2002.
DLR, “Institute of Robotics and Mechatronics, Status Report 1997–2004,” Part 1, pp. 35–42, 2004.
Tuttle, T. D. and Seering, W. P., “A nonlinear model of a harmonic drive gear transmission,” IEEE Int. Conf. on Robotics and Automation, Vol. 12, No. 3, pp. 368–374, 1996.
Dhaouadi, R., Ghorbel, F. H., and Gandhi, P. S., “A new dynamic model of hysteresis in harmonic drives,” IEEE Trans. on Industrial Electronics, Vol. 50, No. 6, pp. 1165–1171, 2003.
Taghirad, H. D. and Belanger, P. R., “Torque ripple and misalignment torque compensation for the built-in torque sensor of harmonic drive systems,” IEEE Trans. on Instrumentation and Measurement, Vol. 47, No. 1, pp. 309–315, 1998.
Godler, I., Ninomiya, T., and Horiuchi, M., “Ripple compensation for torque sensors built into harmonic drives,” IEEE Trans. on Instrumentation and Measurement, Vol. 50, No. 1, pp. 117–122, 2001.
Sensinger, J. W. and Weir, R. F., “Improved torque fidelity in harmonic drive sensors through the union of two existing strategies,” IEEE/ASME Trans. on Mechatronics, Vol. 11, No. 4, pp. 457–461, 2006.
Kim, J. H., Kim, Y. L., and Song, J. B., “A Switching Notch Filter for Reducing the Torque Ripple Caused by a Harmonic Drive in a Joint Torque Sensor,” Trans. of the KSME (A), Vol. 35, No. 7, pp. 709–715, 2011.
Aghili, F., Buehler, M., and Hollerbach, J. M., “Design of a Hollow Hexaform Torque Sensor for Robot Joints,” The International Journal of Robotics Research, Vol. 20, No. 12, pp. 967–976, 2001.
Samick HDS Co. LTD., http://www.shds.co.kr
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kim, IM., Kim, HS. & Song, JB. Design of joint torque sensor with reduced torque ripple for a robot manipulator. Int. J. Precis. Eng. Manuf. 13, 1773–1779 (2012). https://doi.org/10.1007/s12541-012-0233-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-012-0233-x