Abstract
Laser micro-welding has proven to be a very successful tool for micro-joining in the electrical and electronic industries, where the miniaturization, the high strength and the high heat resistance are constantly requested. Recently, a flexible printed circuit (FPC) is expected as a new connection technology between electrical conductors according to the improvements of reliability and controllability with the diversification of the design concept. In this technology, it is required to weld a several tens μm thickness of FPC and a several hundreds μm thickness of metal electrode. This material combination accompanies the difficulty to control the welding phenomenon due to the differences of thermal property and heat capacity. As a good alternative, laser micro-welding has advantages of non-contact tool, low heat distortion and consistent weld integrity. In this study, the overlap welding of thin copper circuit on a polyimide film and a thick brass electrode was experimentally and numerically investigated by using a pulsed Nd:YAG laser. In addition, the shearing stress of overlap welding was evaluated with and without the control of pulse waveform, which can provide a well-directed controlling of the heat input with high energy density. The results showed that a porosity was observed as the major weld defect in the welding process without a pulse control. However, the appropriate controlled laser pulse configuration of micro-welding could remove the weld defects in the molten zone, improve the weld penetration stability and increase the weld strength. The potential benefits of controlled pulse waveform were discussed for the direct laser micro-welding process. It is clarified that the direct laser micro-welding of a thin copper circuit on a polyimide film and a thick brass electrode could be successfully achieved by appropriate controlled pulse waveform and heat input.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Katayama, S. and Kawahito, Y., “Laser Direct Joining of Metal and Plastic,” Scripta Materialia, Vol. 59, No. 12, pp. 1247–1250, 2008.
Ozeki, Y., Inoue, T., Tamaki, T., Yamaguchi, H., Onda, S., Watanabe, W., Sano, T., Nishiuchi, S., Hirose, A. and Itoh, K., “Direct Welding between Copper and Glass Substrates with Femtosecond Laser Pulses,” Applied Physics Express, Vol. 1, Paper No. 082601, 2008.
Kim, J.-W. and Kim, C.-G., “Design of a Laser Welded Thin Metal Tube Structure Incorporating Welding Distortion and Residual Stress,” Int. J. Precis. Eng. Manuf., Vol. 11, No. 6, pp. 925–930, 2010.
Otte, F., Stute, U. and Ostendorf, A., “Micro Welding of Electronic Components with 532nm Laser Radiation,” Proc. of SPIE, Vol. 6458, Paper No. 645804, 2007.
Takahashi, K., Watanabe, T., Matsusaka, S. and Wada, T., “Direct Microjoining of Copper Materials using Laser Beams,” JSME International Journal Series C, Vol. 49, No. 1, pp. 128–134, 2006.
Shannon, G. and Severloh, P., “Laser Microwelding of Copper,” Industrial Laser Solutions, pp. 1–3, 2009.
American Welding Society, “Welding Copper and Copper Alloys,” pp. 10–13, 1997.
Migliore, L., “Laser Materials Processing,” Marcel Dekker, pp. 176–178, 1996.
Ion, J. C., “Laser Processing of Engineering Materials,” Butterworth-Heinemann, pp. 431–433, 2005.
Blom, A., Dunias, P., Van Engen, P., Hoving, W. and De Kramer, J., “Process Spread Reduction of Laser Microspot Welding of Thin Copper Parts Using Real-time Control,” Proc. of SPIE, Vol. 4977, pp. 493–507, 2003.
Japan Society of Thermophysical Properties, “Thermophysical Properties Handbook,” pp. 23–25, 2008.
Naeem, M., “Controlling the Pulse in Laser Welding,” Welding, pp. 1–4, 2004.
Biro, E., Weckman, D. C. and Zhou, Y., “Pulsed Nd:YAG Laser Welding of Copper Using Oxygenated Assist Gases,” Metallurgical and Materials Transactions A, Vol. 33, No. 7, pp. 2019–2030, 2002.
Rohde, M., Markert, C. and Pfleging, W., “Laser Micro-Welding of Aluminum Alloys: Experimental Studies and Numerical Modeling,” Int. J. Adv. Manuf. Technol., Vol. 50, No. 1–4, pp. 207–215, 2010.
Zhang, J., Weckman, D. C. and Zhou, Y., “Effect of Temporal Pulse Shaping on Cracking Susceptibility of 6061-T6 Aluminum Nd:YAG Laser Welds,” Welding Journal, Vol. 87, No. 1, pp. 18s–30s, 2008.
Schmidt, M. and Weigl, M., “Laser-Bonding in High Power Electronics,” Journal of Laser Micro/Nanoengineering, Vol. 5, No. 3, pp. 242–247, 2010.
Witte, R., Liebers, R., Holtz, R., Wilden, J. and Neumann, T., “Laser Welding with Pulsed Solid State Lasers: Strategies and New Developments,” Proc. of the 11th International Symposium on Laser Precision Microfabrication, Paper No. 10-75, 2010.
Naeem, M., Lewis, S. and Chinn, J., “Microwelding Performance Comparison Between a Lower Power (125W) Pulsed Nd:YAG Laser and a Low Power (100–200W) Single Mode Fiber Laser,” Proc. of the 3rd Pacific Int. Conf. on Applications of Lasers and Optics, pp. 721–726, 2008.
Kannatey-Asibu, E., “Principles of Laser Materials Processing,” John Wiley & Sons, pp. 232–235, 2009.
Duley, W. W., “Laser Welding,” John Wiley & Sons, pp. 25–27, 1999.
Laser Institute of America, “LIA Handbook of Laser Materials Processing,” pp. 320–322, 2001.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Ismail, M.I.S., Okamoto, Y., Okada, A. et al. Direct micro-joining of flexible printed circuit and metal electrode by pulsed Nd:YAG laser. Int. J. Precis. Eng. Manuf. 13, 321–329 (2012). https://doi.org/10.1007/s12541-012-0041-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-012-0041-3