Abstract
By means of the end-quenching technique, we investigated the relationship between quenching rate and hardness as well as exfoliation corrosion rating for Al-2.21 Zn-3.59 Mg-0.45 Cu-0.038 Zr (at%) alloy plate. In order to achieve an exfoliation corrosion rating of P or EA, the quenching rate must be greater than approximately 460 °C/min and 300 °C/min, respectively, and the drop degree in hardness should simultaneously be lower than approximately 2.0% and 3.5%, respectively. The results of microstructural and microchemical examination using a scanning transmission electron microscope indicate that a lower quenching rate leads to a higher content of Zn, Mg, and Cu in the grain-boundary particles and a greater width of precipitate-free zones near grain boundaries; therefore, grain-boundary particles with Zn and Mg contents less than approximately 13.39% and 10.23% (at%), respectively, and precipitate-free zones near grain boundaries with widths less than about 107 nm can contribute to an exfoliation corrosion rating better than EA. The amount of quench-induced η-phase particles, which lead to lower hardness, increases with decreasing quenching rate, and the area fraction of these particles is approximately 2.9% at a quenching rate of 300 °C/min.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
S. Liu, C. Li, S. Han, Y. Deng, and X. Zhang, J. Alloy. Compd. 625, 34 (2015).
Y. Deng, L. Wan, Y. Zhang, and X. Zhang, J. Alloy. Compd. 509, 4636 (2011).
S. Liu, Q. Zhong, Y. Zhang, W. Liu, and X. Zhang, Mater. Design 31, 3116 (2010).
S. Y. Chen, K. H. Chen, and G. S. Peng, Trans. Nonferrous Met. Soc. China 22, 47 (2012).
S. D. Liu, B. Chen, C. B. Li, Y. Dai, Y. L. Deng, and X. M. Zhang, Corros. Sci. 91, 203 (2015).
G. P. Dolan and J. S. Robinson, J. Mater. Proc. Technol. 153-154, 346 (2004).
C. E. Bates and G. E. Totten, Heat Treat. Met. 4, 89 (1988).
S. Liu, W. Liu, Y. Zhang, X. Zhang, and Y. Deng, J. Alloy. Compd. 507, 53 (2010).
S. Liu, C. Li, Y. Deng, X. Zhang, and Q. Zhong, Met. Mater. Int. 20, 195 (2014).
J. Tang, H. Chen, X. Zhang, S. Liu, W. Liu, H. Ouyang, and H. Li, Trans. Nonferrous Met. Soc. China 22, 1255 (2012).
S. T. Lim, S. J. Yun, S. W. Nam, Mater. Sci. Eng. A 371, 82 (2004).
X. M. Zhang, W. J. Liu, S. D. Liu, M. Z. Zhou, Mater. Sci. Eng. A 528, 795 (2011).
L. Huang, K. Chen, and S. Li, Mater. Sci. Eng. B 177, 862 (2012).
S. Chen, K. Chen, and G. Peng, Mater. Design 35, 93 (2012).
F. Song, X. Zhang, S. Liu, Q. Tan, and D. Li, Corros. Sci. 78, 276 (2014).
C. Li, S. Liu, G. Wang, Y. Jin, and X. Zhang, Chinese J. Mater. Res. 27, 259 (2013).
J. W. Newkirk and D. S. Mackenzie, J. Mater. Eng. Perform. 9, 408 (2000).
B. W. Ying, Master’s Thesis, pp.41–48, Central South University, Changsha, China (2015).
GB/T 22639-2008, Test Method of Exfoliation Corrosion for Wrought Aluminium and Aluminium Alloys, pp.1–3, Standards Press of China, Beijing, China (2009).
D. McNaughtan, M. Worsfold, and M. J. Robinson, Corros. Sci. 45, 2377 (2003).
S. D. Liu, Y. B. Yuan, C. B. Li, J. H. You, and X. M. Zhang, Met. Mater. Int. 18, 679 (2012).
J. F. Li, Z. W. Peng, and C. X. Li, Trans. Nonferrous Met. Soc. China 18, 755 (2008).
S. J. Pennycook and D. E. Jesson, Ultramicroscopy 37, 14 (1991).
D. A. Porter, K. E. Easterling, and M. Sherif, Phase Transformation in Metals and Alloys, 3rd ed., pp.303–305, CRC Press, Florida (2009).
J. Buha, R. N. Lumley, and A. G. Crosky, Mater. Sci. Eng. A 492, 1 (2008).
S. Liu, C. Li, Y. Deng, and X. Zhang, Acta Metall. Sinica. 48, 343 (2012).
N. Birbilis and R. G. Buchheit, J. Electrochem. Soc. 152, 140 (2005).
J. F. Li, Z. Q. Zheng, S. C. Li, W. J. Chen, W. D. Ren, and X. S. Zhao, Corros. Sci. 49, 2436 (2007).
S. P. Knight, N. Birbilis, and B. C. Muddle, Corros. Sci. 52, 4073 (2010).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Li, D., Yin, B., Lei, Y. et al. Critical quenching rate for high hardness and good exfoliation corrosion resistance of Al-Zn-Mg-Cu alloy plate. Met. Mater. Int. 22, 222–228 (2016). https://doi.org/10.1007/s12540-016-5504-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12540-016-5504-0