Abstract
Gear skiving has received considerable attention because of its high productivity, particularly in internal gear cutting, and skiving cutter design methods have been widely investigated. At the beginning of a cutter design process, a shaft angle, a center distance, and the number of teeth are examined as basic parameters for cutting gears. In current gear skiving, a shaft angle is generally set to be approximately 20°; however, the reason for selecting this value has not been clarified. In the present study, the validity of the value of shaft angle is discussed by calculating the cutting tool parameters, such as instantaneous rake angles, clearance angles, cut depths, and cutting speeds at continuously moving cutting points against various shaft angles. Therefore, the widely used value of shaft angle would result in moderate cutting tool parameters. In addition, the cutting force and cutter wear would be low when a cutter axis inclines opposite to the gear helix to be cut.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Y. Fu, Y. Liu, L. Cui and X. Xu, Dynamic analysis and control strategy of wet clutches during torque phase of gear shift, Journal of Mechanical Science and Technology, 30 (4) (2016) 1479–1496.
D. Qin, M. Yao, S. Chen and S. Lyu, Shifting process control for two-speed automated mechanical transmission of pure electric vehicles, International Journal of Precision Engineering and Manufacturing, 17 (5) (2016) 623–629.
H. Ma, R. Feng, X. Pang, R. Song and B. Wen, Effects of tooth crack on vibration responses of a profile shifted gear rotor system, Journal of Mechanical Science and Technology, 29 (10) (2015) 4093–4104.
C. Kobialka, Contemporary gear pre-machining solutions, GearSolutions (2013) April, 42-49.
W. V. Pittler, Verfahren zum Schneiden von Zahnradern mittels eines zahnradartigen, an den Stirnflachen der Zahn emit Schneidkanten versehenen Scchneidwerkzeugs, Patentschrift, 243514 (1912).
H. Stadtfeld, Power skiving of cylindrical gears on different machines platform, Gear Technology, 31 (1) (2014) 52–49.
E. Guo, R. Hong, X. Huang and C. Fang, Research on the design of skiving tool for machining involute gears, Korean Journal of Mechanical Science and Technology, 28 (12) (2014) 5107–5115.
F. L. Litvin and A. Fruentes, Gear geometry and applied theory, 2nd ed., Cambridge University Press, New York (2004).
I. Moriwaki, T. Osafune, M. Nakamura, M. Funamoto, K. Uriu, T. Murakami, E. Nagata, N. Kurita, T. Tachikawa and Y. Kobayashi, Cutting tool parameters of cylindrical skiving cutter with sharpening angle for internal gears, Journal of Mechanical design, 033301, 139, March (2017).
K. Uriu, T. Osafune, T. Murakami, M. Nakamura, D. Iba, M. Funamoto and I. Moriwaki, Study on design of taper shaped skiving cutters for internal gears, Transaction of the Japan Society of Mechanical Engineers, 83 (853) (2017).
F. W. Taylor, On the art of cutting metals, American Society of Mechanical Engineers.
K. Yoshida and J. Minato, Simple estimation method of cutting forces in cylindrical turning, Transaction of the Japan Society of Mechanical Engineers, Series C, 79 (808) (2013-12).
Author information
Authors and Affiliations
Corresponding author
Additional information
Koichiro Uriu received his B.S. degree from Kyusyu University in Japan in 1998 and is currently a Ph.D. candidate at Kyoto Institute of Technology. His research interests include machine tools for gear manufacturing and cutters.
Rights and permissions
About this article
Cite this article
Uriu, K., Osafune, T., Murakami, T. et al. Effects of shaft angle on cutting tool parameters in internal gear skiving. J Mech Sci Technol 31, 5665–5673 (2017). https://doi.org/10.1007/s12206-017-1107-z
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-017-1107-z