Abstract
Thermal performance assessments, flow configurations and heat transfer characteristics in a fin-and-oval-tube heat exchanger with the delta winglet vortex generators are examined numerically. Delta winglet vortex generators like V-ribs are placed on fin surfaces with V-tip pointing upstream called “V-Upstream”. The effects of the flow attack angles (α = 15°, 30°, 45° and 60°) and the distances between V-tip to the center of the oval tube in transverse line (Transverse pitch, a = 3.77, 4.77 and 5.77 mm) on heat transfer, flow structure and thermal performance are studied for Reynolds number based on the hydraulic diameter of the test channel, Re = 500 − 2500. The numerical results are presented in four parts: validations of the base case, flow configurations, velocity field, heat transfer and thermal performance assessment. It is found that the use of the delta winglet vortex generators can help to improve heat transfer rate in the heating system by creating vortex flow and swirl flow over the test channel. The heat transfer and pressure loss appeared to be higher than the plain fin for all case studies. The augmentation of the flow attack angle results in the rise of heat transfer rate and friction loss, while differences in transverse pitch produced similar values in terms of the Nusselt number and friction loss. In addition, augmentations are found around 1.15 − 1.55 and 1.5 − 3.4 times over the base case for heat transfer and friction factor, respectively. At Re = 2500, a = 5.77 mm and α = 15°, the maximum thermal enhancement factor is found to be around 1.12.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
W. R. Pauley and J. K. Eaton, The effect of embedded longitudinal vortex array on turbulent boundary layer heat transfer, J. Heat Transfer, 116 (1994) 871–85.
D. E. Wroblewski and P. A. Eibeck, Measurements of turbulent heat transfer in a boundary layer with an embedded streamwise vortex, Int. J. Heat Mass Transfer, 34 (7) (1991) 1617–1631.
E. Kim and J. S. Yang, An experimental study of heat transfer characteristics of a pair of longitudinal vortices using color capturing technique, Int. J. Heat Mass Transfer, 45 (2002) 3349–3356.
N. Depaiwa, T. Chompookham and P. Promvonge, Thermal enhancement in a solar air heater channel using rectangular winglet vortex generators, International conference on energy and sustainable development (2010) 1–7.
W. Qiuwang, C. Qiuyang, W. Ling, Z. Min, H. Yanping and X. Zejun, Experimental study of heat transfer enhancement in narrow rectangular channel with longitudinal vortex generators, Nuclear Eng. Design, 237 (2007) 686–693.
M. Jian, P. H. Yan, H. Jun, L. W. Yan and W. W. Qiu, Experimental investigations on single-phase heat transfer enhancement with longitudinal vortices in narrow rectangular channel, Nuclear Eng. Design, 240 (2010) 92–102.
C. Min, C. Qi, X. Kong and J. Dong, Experimental study of rectangular channel with modified rectangular longitudinal vortex generators, Int. J. Heat Mass Transfer, 53 (2010) 3023–3029.
C. Habchi, S. Russeil, D. Bougeard, J. L. Harion, T. Lemenand, D. D. Valle and H. Peerhossaini, Enhancing heat transfer in vortex generator-type multifunctional heat exchangers, Appl. Therm. Eng., 38 (2012) 14–25.
B. A. Sarac and T. Bali, An experimental study on heat transfer and pressure drop characteristics of decaying swirl flow through a circular pipe with a vortex generator, Exp. Therm. Fluid Sci., 32 (2007) 158–165.
J. M. Wu and W. Q. Tao, Numerical study on laminar convection heat transfer in a rectangular channel with longitudinal vortex generator Part A: Verification of field synergy principle, Int. J. Heat Mass Transfer, 51 (2008) 1179–1191.
J. M. Wu and W. Q. Tao, Numerical study on laminar convection heat transfer in a channel with longitudinal vortex generator. Part B: Parametric study of major influence factors, Int. J. Heat Mass Transfer, 51 (2008) 3683–3692.
G. Biswas and H. Chattopadhyay, Heat transfer in channel with built-in wing-type vortex generators, Int. J. Heat Mass Transfer, 35 (4) (1992) 803–814.
S. T. Ahmed, W. S. Mohammed and J. H. Laith, Numerical investigation into velocity and temperature fields over smooth and rough ducts for several types of turbulators, J. Eng. Technology, 25 (10) (2007) 1110–1128.
S. R. Hiravennavar, E. G. Tulapurkara and G. Biswas, A note on the flow and heat transfer enhancement in a channel with built-in winglet pair, Int. J. Heat Fluid Flow, 28 (2007) 299–305.
G. Biswas, P. Deb and S. Biswas, Generation of longitudinal streamwise vortices-a device for improving heat exchanger design, J. Heat Transfer, 116 (1994) 588–597.
A. Sohankar, Heat transfer augmentation in a rectangular channel with a vee-shaped vortex generator, Int. J. Heat Fluid Flow, 28 (2007) 306–317.
J. S. Leu, Y. H. Wu and J. Y. Jang, Heat transfer and fluid flow analysis in plate-fin and tube heat exchangers with a pair of block shape vortex generators, Int. J. Heat Mass Transfer, 47 (2004) 4327–4338.
A. D. Sommers and A. M. Jacobi, Air-side heat transfer enhancement of a refrigerator evaporator using vortex generation, Int. J. Refrig., 28 (2005) 1006–1017.
S. M. Pesteei, P. M. V. Subbarao and R. S. Agarwal, Experimental study of the effect of winglet location on heat transfer enhancement and pressure drop in fin-tube heat exchangers, Appl. Therm. Eng., 25 (2005) 1684–1696.
Y. Chen, M. Fiebig and N. K. Mitra, Heat transfer enhancement of a finned oval tube with punched longitudinal vortex generators in-line, Int. J. Heat Mass Transfer, 41 (1998) 4151–4166.
Y. Chen, M. Fiebig and N. K. Mitra, Heat transfer enhancement of finned oval tube with staggered punched longitudinal vortex generators, Int. J. Heat Mass Transfer, 43 (2000) 417–435.
S. Tiwari, D. Maurya, G. Biswas and V. Eswaran, Heat transfer enhancement in cross-flow heat exchangers using oval tubes and multiple delta winglets, Int. J. Heat Mass Transfer, 46 (2003) 2841–2856.
J. E. O’Brien, M. S. Sohal and P. C. Wallstedt, Local heat transfer and pressure drop for finned-tube heat exchangers using oval tubes and vortex generators, J. Heat Transfer, 126 (2004) 826–835.
P. Chu, Y. L. He, Y. G. Lei, L. T. Tian and R. Li, Threedimensional numerical study on fin-and-oval-tube heat exchanger with longitudinal vortex generators, Appl. Therm. Eng., 29 (2009) 859–876.
A. I. ElSherbini and A. M. Jacobi, The thermal-hydraulic impact of delta-wing vortex generators on the performance of a plain-fin-and-tube heat exchanger, HVAC&R Research, 8 (4) (2002) 357–370.
A. Joardar and A. M. Jacobi, Heat transfer enhancement by winglet-type vortex generator arrays in compact plain-finand-tube heat exchangers, Int. J. Refrig, 31 (2008) 87–97.
A. Joardar and A. M. Jacobi, A numerical study of flow and heat transfer enhancement using an array of deltawinglet vortex generators in a fin-and-tube heat exchanger, J. Heat Transfer, 129 (9) (2006) 1156–1167.
K. M. Kwak, K. Torii and K. Nishino, Heat transfer and flow characteristics of fin-tube bundles with and without winglet-type vortex generators, Exp. in Fluids, 33 (2002) 696–702.
C. M. B. Russell, T. V. Jones and G. H. Lee, Heat transfer enhancement using vortex generators, Heat Transfer, Proc. Seventh Heat Transfer Conference, 3 (1982) 283–288.
P. Sriromreun, C. Thianpong and P. Promvonge, Experimental and numerical study on heat transfer enhancement in a channel with Z-shaped baffles, Int. Comm. Heat Mass Transfer, 39 (2012) 945–952.
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended by Associate Editor Ji Hwan Jeong
Withada Jedsadaratanachai has a doctorate in Mechanical Engineering, King Mongkut’s Institute of Technology Ladkrabang (KMITL), Bangkok, Thailand. She is a lecturer in \ Mechanical Engineering, KMITL. Her research works are about computational fluid dynamic (CFD), mathematical model and thermo-fluid.
Amnart Boonloi is an Assistant Professor of Mechanical Engineering Technology at King Mongkut’s University of Technology North Bangkok (KMUTNB), Thailand. He obtained his D.Eng. in Mechanical Engineering from King Mongkut’s Institute of Technology Ladkrabang in 2011. His research interests include Thermal&Fluid engineering, heat transfer enhancement and computational fluid dynamics and drying technology.
Rights and permissions
About this article
Cite this article
Jedsadaratanachai, W., Boonloi, A. Thermal performance assessment in a fin-and-oval-tube heat exchanger with delta winglet vortex generators. J Mech Sci Technol 29, 1765–1779 (2015). https://doi.org/10.1007/s12206-015-0350-4
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-015-0350-4