Abstract
Semi-solid metal (SSM) processing has been recognized as an advanced process to produce high-quality and low-cost engineering components. The cooling slope method is a simple route that can develop non-dendritic slurry for various purposes with reduced equipment and processing costs. In this study, the cooling slope method was employed to produce the A356 feedstock in SSM processing. The dendritic primary phase in the conventionally cast A356 alloy has transformed into a non-dendritic one through the use of ingots cast over a cooling plate with a different pouring temperature. After pouring, the melt that becomes semi-solid at the end of the plate is consequently poured into cylindrical steel molds with different mold temperatures. Also, the process has been conducted in different cooling slopes and different cooling lengths. Then, a back-propagation neural network has been designed to correlate the process parameters to grain size. Finally, genetic algorithm (GA) has been used to optimize the process parameters. Results indicate that the pouring temperature, mold temperature, cooling slope, and cooling length have significant effects on size and morphology of α-Al phase. The GA can optimize the process as well.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Z. Fan, Semi-solid metal processing, International materials reviews, 47(2) (2002) 1–37.
M. P. Kenney, J. A. Courtois and R. D. Evans, Metals handbook vol. 15, 9th edition, ASM International, Metals Park, Ohio, USA (1988).
F. Taghavi, H. Saghafian and Y. H. K. Kharrazi, Study on the ability of mechanical vibration for the production of thixotropic microstructure in A356 aluminum alloy, Materials and Design, 30(1) (2009) 115–121.
F. Taghavi and A. Ghassemi, Study on the effects of the length and angle of inclined plate on the thixotropic microstructure of A356 aluminum alloy, Materials and design, 30(5) (2009) 1762–1767.
Y. Birol, A357 thixoforming feedstock produced by cooling slope casting, Journal of Materials Processing Technology, 186 (2006) 94–101.
E. C. Legoretta, H. V. Atkinson and H. Jones, Cooling slope casting to obtain thixotropic feedstock II: observations with A356 alloy, Journal of Materials Science, 43(16) (2008) 5456–5469.
H. J. Li, L. H. Qi, H. M. Han and L. J. Guo, Neural network modeling and optimization of semi-solid extrusion for aluminum matrix composites, Journal of Materials Processing Technology, 151 (2004) 126–132.
H. Jiang, T. H. Nguyen and M. Prud’homme, Optimal control of induction heating for semi-solid aluminum alloy forming, Journal of Materials Processing Technology, 189 (2007) 182–191.
J. H. Park, J. C. Choi, Y. H. Kim and J. M. Yoon, A study of the optimum reheating process for A356 alloy in semi-solid forging, International Journal of Advanced Manufacturing Technology, 20(4) (2002) 277–283.
A. Berrado and A. Rassili, Modeling and characterizing of the thixoforming of steel process parameters — the case of forming load International Journal of Material Forming, 3(1) (2010) 735–738.
S. S. Rao, Engineering optimization: theory and practice, John Wiley & Sons, New Jersey (2009).
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended by Associate Editor Mohammad Abdul Aziz Irfan
Salman Nourouzi is an associate professor of metallurgy and materials engineering at Babol University of Technology in Iran. His subjects of interest include semi-solid forming, thermal spray coating, and heat treatment of metallic alloys.
Rights and permissions
About this article
Cite this article
Nourouzi, S., Baseri, H., Kolahdooz, A. et al. Optimization of semi-solid metal processing of A356 aluminum alloy. J Mech Sci Technol 27, 3869–3874 (2013). https://doi.org/10.1007/s12206-013-0931-z
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-013-0931-z