Abstract
Fatigue life of GFRP (glass-fiber reinforced plastic) composites used in wind turbine rotor blades has been evaluated considering the glass fiber orientations. Three different laminate composites with the respective laminating orientation of 0°, ±45°, and 0°±45° were prepared using vacuum infusion method. Tensile properties and S-N curves for these composites were experimentally determined at room temperature. From the tensile tests, it was found that tensile properties were greatly dependent upon the fiber orientation and the tensile strength of unidirectional composite was the largest and bidirectional (45°) composite was the weakest among three composites. The fatigue properties were determined under constant amplitude load control at different stress ratios, R, of 0.5, 0.1 and −0.2. The properties also show the dependency of stress ratios and fiber orientation. The fatigue life diagrams of these three composite were relatively well presented with the double logarithmic S-N curve. The linear slopes of the respective S-N curves for three composite were not greatly different. The fatigue limits for the composites were evaluated and predicted with linear Goodman and Gerber diagrams.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Global Wind Report 2009, GWEC.
J. F. Mandell, R. M. Reed and D. D. Samborsky, Fatigue of fiberglass wind turbine blade materials, Sandia National Laboratory contractor report: SAND92-7005, Montana State University, August (1992).
J. W. Kim, J. J. Lee and D. G. Lee, The comparison of the tensile strength of fiber-reinforced composites according to the change of fiber orientation and fiber orientation angle in one direction, Journal of the Korean Society for Composite Materials (2004) 284–287.
R. P. L. Nijssen, Fatigue life prediction and strength degradation of wind turbine rotor blade composites, SAND2006-7810P, Unlimited Release, October (2007).
H. Zhou, L. Mishnaevsky Jr., P. Brøndsted, J. B. Tan and L. L. Gui, SEM in-situ laboratory investigations on damage growth in GFRP composite under three-point bending tests, Project UpWind, Contract No.:019945 (SES6).
H. Mivehchi and A. Varvani-Farahani, The effect of temperature on fatigue damage of FRP composites, J Mater Sci (45) (2010) 3757–3767.
ISO 527-4, Plastic determination of tensile properties_part4: Test conditions for isotropic and orthotropic fiber-reinforced plastic composites.
ASTM D 5083, Standard test method for tensile properties of reinforced thermosetting plastics using straight-sides specimens.
A. Varvani-Farahani and A. Shirazi, A fatigue damage model for (0/90) FRP composites based on stiffness degradation of 0° and 90° composite plies, J Reinf Plast Composite, 26(13) (2007) 1319–36.
G. Lloyd, Rules and regulations, IV-Non-Marine Technology, Part I: Wind Energy, Hamburg, Germany (1993) 2–2.
G. Lloyd, Rules and regulations, IV-Non-Marine Technology, Part I: WindEnergy, Hamburg, Germany (2003) 5–19.
J. S. Stölken and A. G. Evans, A microbend test method for measuring the plasticity length scale, Acta Materialia, 46(14) (1998) 5109–5115.
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended by Guest Editor Dong-Ho Bae
Yong-Hak Huh received his B.S. in Mechanical Engineering from Hanyang University, Korea, in 1984. He then received his M.S. and Ph.D degrees from KAIST in 1987 and 1998, respectively. Dr. Huh is currently a Principal Research Scientist at KRISS in Daejon, Korea. His research interests include material measurement and reliability in materials and structure.
Rights and permissions
About this article
Cite this article
Huh, YH., Lee, JH., Kim, DJ. et al. Effect of stress ratio on fatigue life of GFRP composites for WT blade. J Mech Sci Technol 26, 2117–2120 (2012). https://doi.org/10.1007/s12206-012-0526-0
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-012-0526-0