Abstract
Ink transfer process from the printing roll to the web was investigated using a Computational Fluid Dynamics (CFD) technique for the roll-to-roll (R2R) printing application. A parametric study was conducted to identify the effects of fluid parameters such as viscosity, surface tension and contact angle. To make the present analysis more relevant to the real printing system, a three-dimensional computational configuration for the commercial software was set up using the information obtained from the typical R2R system. Simplified one-dimensional semi-analytic model based on Reynolds equation was compared with the CFD results to assess the validity of the results. Pressure distribution states that 1-D analysis is reasonably good in capturing the flow physics. The 3-D simulation with VOF (Volume of Fluid) shows that viscosity is the most important parameter. Moreover, the larger surface tension resulted in smaller amount of ink transfer.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
M. Pudas, J. Hagberg and S. Leppävuori, Printing parameters and ink components affecting ultra-fine-line gravure-offset printing for electronics applications, J. Eur. Ceram. Soc. 24 (2004) 2943–2950.
P. Hahne, E. Hirth, I. E. Reis, K. Schwichtenberg, W. Richtering, F. M. Horn and U. Eggenweiler, Progress in thickfilm pad printing technique for solar cells, Solar Energy Materials & Solar Cells 65 (2001) 399–407.
N. Kapur, A parameteric study of direct gravure coating, Chem. Eng. Sci. 58 (2003) 2857–2882.
G. A. Zevallos et al, Forward roll coating flows of viscoelastic liquids, J. Non-Newtonian Fluid Mech. 130 (2005) 96–109.
Xiuyan Yin and Satish Kumar, Flow visualization of the liquid-emptying process in scale-up gravure grooves and cells, Chem. Eng. Sci. 61 (2006) 1146–1156.
L. E. Rodd, T. P. Scott, J. J. Cooper-White and G. H. Mckinley, Capillary break-up rheometry of low-viscosity elastic fluids, HML Report Number 04-P-04, (2004).
M. Yao, S. H. Spiegelberg and G. H. Mckinley, Dynamics of weakly strain-hardening fluids in filament stretching devices, J. Non-Newtonian Fluid Mech. 89 (2000) 1–43.
Andrea Bonito, Marco Picasso and Manuel Laso, Numerical simulation of 3D viscoelastic flows with free surfaces, J. Comput. Phy. 215 (2006) 691–716.
K. S. Sujatha, H. Matallah, M. J. Banaai and M. F. Webster, Computational predictions for viscoelastic filament stretching flows: ALE methods and free surface techniques (CM and VOF), J. Non-Newtonian Fluid Mech. 137 (2006) 81–102.
X. Yin, S. Kumar, Lubrication flow between a cavity and a flexible wall, Phys. Fluids 17 (2005) 063101.
C.W. Hirt and B.D. Nichols, Volume of fluid (VOF) method for the dynamics of free boundaries, J. Comput. Phys. 39 (1981) 201–225.
Author information
Authors and Affiliations
Corresponding author
Additional information
Sangwon Lee received his B.S. and M. S. degrees in mechanical engineering from Konkuk University, Korea. Now, he is working with Samsung Electronics. His research interest is in the area of computational fluid dynamics.
Yang Na received his B.S. and M. S. degrees in mechanical engineering from Seoul National University, Korea and Ph. D. degree from Stanford University, U.S.A. His research interest is in the area of computational fluid dynamics and convective heat transfer.
Rights and permissions
About this article
Cite this article
Lee, S., Na, Y. Analysis on the ink transfer mechanism in R2R application. J Mech Sci Technol 24, 293–296 (2010). https://doi.org/10.1007/s12206-009-1146-1
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-009-1146-1