Abstract
Background
Because the clinical and radiographic performance of an ultrashort anatomic cementless stem has been investigated in only two randomized controlled studies, well-designed trials should aim for a thorough comparison of the outcomes of ultrashort anatomic cementless and conventional anatomic cementless stems.
Questions/purposes
The purposes of this study were to compare (1) the clinical results, including Harris hip score, thigh pain, and WOMAC index score, (2) radiographic results, (3) bone mineral density; and (4) proportions of patients undergoing revision of a THA using an ultrashort anatomic cementless stem versus a conventional anatomic cementless stem in the same patients who underwent bilateral sequential THAs under the same anesthetic.
Methods
Two hundred patients (mean age, 53 years; range, 26–54 years) who underwent bilateral sequential THAs received an ultrashort anatomic cementless stem in one hip and a conventional anatomic cementless stem in the contralateral hip. From January 2004 to December 2005, we performed 524 same-day bilateral short and conventional anatomic cementless THAs in 262 patients, of whom 212 (81%) participated in this study. Five patients were lost to followup before 2 years, five were lost between 2 to 10 years, and two were lost between 10 to 13 years, leaving 200 patients. Patients who had end-stage bilateral hip disease and were younger than 55 years were selected for inclusion. The predominant diagnoses were osteonecrosis (118 patients, 59%) and osteoarthritis (44 patients, 22%). One hundred thirty-eight were men and 62 were women. At the time of each followup, the patients were assessed clinically and radiographically. In addition, each patient completed the WOMAC and the University of California Los Angeles (UCLA) activity scores. The minimum followup was 10 years (mean, 11.8 years; range, 10–13 years). Followups were done in person, with all images and followup clinic notes. Based on the power analysis, we estimated a sample size of 178 hips was needed in each group to detect a 3-point difference in the Harris hip score with 80% power.
Results
At the latest followup, there were no differences between the two groups regarding the mean Harris hip scores (94 versus 94 points; p = 0.189), mean WOMAC scores (17 versus 16 points; p = 0.191), or mean UCLA activity scores (9 versus 9 points; p = 0.381). Two patients in the ultrashort stem group and one patient in the conventional stem group had severe (9 points) thigh pain, and 30 patients (15%) in the conventional stem group had mild thigh pain (2 or 3 points) after vigorous exercise. Bone mineral density in the ultrashort and conventional stem groups, respectively, was greater in the ultrashort stem group than in the conventional stem group. Bone mineral density in Zone 1 at 12 years was 3.29 versus 1.88 g/cm2 (p = 0.021), and 2.97 versus 0.91 g/m2 in Zone 7 (p = 0.001). With the numbers available, there were no differences between the stem designs in terms of the proportion undergoing revision (one hip, 0.5%, in the short-stem group versus one hip, 0.5%, in the conventional group; p = 1.881).
Conclusions
At followup into the second decade, ultrashort stems showed no differences from conventional cementless stems in terms of validated outcomes scores or fixation, although less stress shielding was observed. Reduction of stress shielding may reduce the long-term risk of periprosthetic fracture, but this was not shown in our study.
Level of Evidence
Level I, therapeutic study.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Conventional cementless femoral stems are known to provide a high rate of satisfactory clinical and radiographic performance at long-term followups [1, 7, 12, 14, 15, 18, 33]. However, they may have potential clinical consequences related to stress shielding, thigh pain, periprosthetic fractures, proximodistal dimensional mismatch, and removal during revision [9, 11, 16, 17, 19, 21–23, 35, 38]. In an effort to reduce the risk of stress shielding, thigh pain, periprosthetic fracture, and proximodistal dimensional mismatch and to facilitate removal of a well-fixed stem, an ultrashort anatomic (left or right) metaphyseal-fitting cementless femoral stem was developed. The absence of the diaphyseal anchorage sought to achieve more-proximal load transfer to reduce stress shielding, thigh pain, and proximodistal dimensional mismatch; it also sought to preserve more diaphyseal bone for future revisions [4, 16, 17, 19, 21–23, 35, 41]. Biomechanical studies showed that ultrashort cementless stems exhibited good fixation and sustained high loads to failure with axial loading [35, 40]. However, there are concerns about lower loads to failure regarding torsional loads in the proximal femur [36]. Thus, the distal fixation achieved with a conventional cementless stem may provide greater resistance to torsional loads [29]. Questions regarding whether an ultrashort stem will be sufficiently biomechanically stable to achieve durable bone ingrowth and longer-term clinical performance have been raised [17, 21, 22, 34].
Because clinical and radiographic performance of this ultrashort anatomic cementless stem have been investigated in only a few studies and at short-term followup [16, 17, 19, 21–23, 34], it remains to be determined whether an ultrashort anatomic cementless stem shows similar clinical and radiographic results, bone mineral density (BMD), and revision rate as a conventional cementless stem at long-term followup.
The purposes of this prospective randomized study were to compare (1) the clinical results, including Harris hip score [13], thigh pain, and WOMAC index score; (2) radiographic results, including stress shielding, and implant aseptic loosening; (3) BMD; and (4) proportions of patients undergoing revision of cementless THA using an ultrashort anatomic metaphyseal-fitting cementless stem versus a conventional anatomic proximal porous-coated cementless stem in the same patients who underwent bilateral sequential THAs under one anesthetic.
Patients and Methods
From January 2004 to December 2005, a total of 262 patients (524 hips) underwent bilateral sequential THAs under the same anesthetic and were considered for inclusion in this within-patient randomized trial. Of these, 212 patients (424 hips) met the inclusion criteria and agreed to participate in the study. Patients were excluded if they were older than 55 years (the age limit was chosen arbitrarily considering activity level), they had inflammatory arthritis, or they had a foot or ankle disorder that limited walking. Contraindications for an ultrashort stem were patients with a high-riding dislocation of the femoral head, severe osteoporosis, or intertrochanteric fracture. The study protocol, including the consent forms, was approved by the institutional review board at our institution. All patients provided informed consent. Twelve patients were lost to followup, but no patient died during the interim, leaving 200 patients (400 hips) available for study with a minimum duration of followup of 10 years (mean, 11.8 years; range, 10–13 years) (Fig. 1).
There were 138 men and 62 women with a mean age of 52.5 years (range, 26–54 years) at the time of surgery. The mean height of the patients was 168.2 cm (range, 158–183 cm) and mean body weight was 83 kg (range, 69–118 kg). The mean BMI was 29.6 kg/m2 (range, 27.6–35.8 kg/m2). The diagnosis was osteonecrosis of the femoral head in 118 patients (59%), osteoarthritis in 44 (22%), osteoarthritis secondary to childhood septic arthritis in 18 (9%), ankylosing spondylitis in 10 (5%), and multiple epiphyseal dysplasia in 10 (5%). There were no differences between the two groups in terms of preoperative conditions, including the extent of disease, pain, functional disability, deformity, ROM, bone loss, and/or prior surgical treatments (Table 1).
Randomization to treatment with an ultrashort anatomic cementless stem or a conventional anatomic cementless stem was accomplished using study numbers in sealed envelopes, which were opened in the operating room before the skin incision was made. All patients were equally assigned, using a computer program, to receive one type of component in one hip and another type in the contralateral hip. This study was done by intent-to-treat. The first hip received the prosthesis indicated in the envelope and the contralateral hip received the other prosthesis. No patients had the second procedure aborted because of intraoperative problems such as hypotension or heart problems.
All operations were performed by the senior author (YHK) using a posterolateral approach. The ultrashort anatomic cementless (Proxima™; DePuy, Leeds, UK) stem is made of titanium alloy and is entirely porous coated with sintered titanium beads, having a mean pore size of 250 μm, to which a 30-μm thick hydroxyapatite coating is applied, except at the distal tip (Fig. 2). The femoral neck was cut horizontally at the head-neck juncture. The proximal femur was prepared by the “round the corner” technique [17, 23, 34]. The size of the femoral component selected matched the size of the largest broach used. Stability of the femoral component was determined by the torsional stability of the stem as dictated by bone quality rather than by canal fit and fill. A 28-mm diameter BIOLOX® forte ceramic femoral head (CeramTec AG, Polchingen, Germany) was used in all hips. A cementless DURALOC® cup (DePuy, Warsaw, IN, USA) with a 28-mm internal-diameter BIOLOX® forte ceramic liner (CeramTec) was used in all hips.
The conventional anatomic cementless stem (Profile®; DePuy) is made of titanium alloy and is an anatomic metaphyseal and diaphyseal fit and fill, not a tapered stem. The proximal 1/3 of the stem is porous-coated with titanium sintered beads. This stem also has a smooth diaphyseal stem below the metaphyseal porous coating (Fig. 2). The pore size was 250 μm. A 28-mm diameter BIOLOX® forte ceramic femoral head was used in all hips. A cementless DURALOC® cup and a 28-mm internal diameter BIOLOX® forte ceramic liner were used in all hips. The conventional anatomic cementless femoral component was inserted with a press-fit as determined by the preoperative use of templates. At the time of the operation, an attempt was made to fill the femoral canal with the broach, leaving little cancellous bone remaining. The mean duration of the THA for each hip was 55 minutes (range, 48–101 minutes).
Patients were mobilized on the second postoperative day and progressed to full weightbearing with a walker or crutches as comfort permitted; they were advised to use a walking aid for 6 weeks [23, 24]. The patients were reviewed at 3 months, 1 year, and yearly thereafter, by one of the authors (JWP), who was not directly involved in the treatment of the patients. The Harris hip score [13] and WOMAC score [2] were recorded at each visit. Thigh pain was scored on a 10-point VAS [6], where 0 represents no pain and 10 equals severe pain. Activity level was assessed at the most recent followup using the UCLA activity score [42]. All the data were collected and analyzed by a research associate (DRK) who was not part of the surgical team. Any clicking or squeaking sound from the ceramic-on-ceramic bearing was recorded. At each followup, all patients were asked specifically, by an examiner (YHK), whether they heard a clicking or squeaking sound.
Radiologic evaluation was done at 3 months and 1 year postoperatively and yearly thereafter. A supine AP radiograph of the pelvis with both hips in extension with 15° internal rotation and a crosstable lateral radiograph of each hip were obtained 7 days postoperatively and at each subsequent visit. The morphologic features of the femur were determined preoperatively using Dorr’s classification system [8]. Femoral component position in the coronal and sagittal planes, center of rotation in the horizontal and vertical planes, femoral offset, abductor moment arm, femoral neck length, and limb-length discrepancy also were analyzed. Anteversion and inclination of the acetabular component were measured, using the method of Engh et al. [10], by a research associate (DRK) who was not directly involved in the treatment of patients.
Definite loosening of the femoral component was defined when there was progressive axial subsidence greater than 3 mm or a varus or valgus shift greater than 3° [19]. The degree of stress shielding was assessed by Engh and Bobyn’s criteria [9]. Osteolytic lesions were assessed for their location and size using the method of Zicat et al. [43]. Radiographic data were analyzed by a research associate (DRK) with no knowledge of the patient’s name. The intraobserver error in all the radiographic measurements ranged from 0.95 to 1.00 by the chance-corrected kappa coefficient [25], indicating excellent reproducibility. BMD was determined using dual-energy X-ray absorptiometry (DEXA) as reported by Kim et al. [16, 17, 19–22]. DEXA scans were taken at 1 week, 1 year, 10 years, and at the final followup after surgery (mean, 11.8 years). BMD data was analyzed, by one observer (DRK), from the lower border of the lesser trochanter to the tip of the greater trochanter in Zone 1 and from the lower border of the lesser trochanter to the femoral neck-cut level in Zone 7. The intraobserver error for BMD analysis was 0.95 (range, 0.91–0.97) by the chance-corrected kappa coefficient [25], indicating excellent reproducibility.
To detect an effect size of 0.5, corresponding to an anticipated difference of 3 points in the Harris hip score and a SD of 6 points, we calculated that 178 patients were required in each group. In anticipation of a 10% dropout rate, we aimed to include 200 patients in each group. The two-tailed Student’s t-test was used to evaluate the changes in Harris hip score. To analyze complication rates and the radiologic data, the chi-square test with Yate’s correction was used. BMD was compared using a two-tailed Student’s t-test [21].
A probability level of 0.05 was used for all tests. Statistical analyses were performed using SPSS Statistics for Windows (version 14.0, SPSS Inc, Chicago, IL, USA).
Results
Comparison of mean preoperative and postoperative Harris hip scores, WOMAC scores, and UCLA activity scores revealed no differences between the two groups. The mean preoperative Harris hip score was 48 points for the ultrashort stem group and 45 points for the conventional stem group (mean difference, 3 points; 95% CI, −3.6 to 8.0; p = 0.189). The mean postoperative Harris hip score was 93.5 points for the ultrashort stem group and 94 points for the conventional stem group (mean difference, 0.5 points; 95% CI, −1.41 to 2.83; p = 0.189). The mean preoperative WOMAC score was 62 points for the ultrashort stem group and 59 points for the conventional stem group (mean difference, 3 points; 95% CI, −2.9 to 7.5; p = 0.114). The mean postoperative WOMAC score was 17 points for the ultrashort stem group and 16 points for the conventional stem group (mean difference, 1 point; 95% CI, −1,62 to 3.11; p = 0.191). The mean preoperative UCLA activity score was 2 points for both groups (mean difference, 0 points; 95% CI, −0.7 to 0.8l; p = 0.151). The mean postoperative UCLA activity score was 8.7 points for both groups (mean difference, 0 points; 95% CI, −0.7 to 0.9; p = 0.381). Thigh pain was more common with the conventional anatomic stem. Two patients (1%) had severe (9 points) thigh pain in the ultrashort anatomic cementless stem group, and the remaining 198 patients in this group had no thigh pain. Twenty-six patients (13%) had mild (2 or 3 points) thigh pain, four (2%) had moderate (5 or 6 points) thigh pain, and one (0.5%) had severe (9 points) thigh pain in the conventional stem group. There was a greater odds of thigh pain with the conventional stem compared with the ultrashort stem (odds ratio, 15; 95% CI, 11.9–21.8; p = 0.045).
The morphologic features of the proximal femur [8], position of the femoral component, center of rotation, femoral offset, abductor moment aim, femoral neck length, leg length discrepancy, and inclination and anteversion of the acetabular component did not differ between the two groups (Table 2). All but two hips in the ultrashort stem group and all but one in the conventional stem group had solid fixation by bone ingrowth (Fig. 3). Two ultrashort stems were unstable. All hips in the ultrashort anatomic cementless stem group showed Grade 1 stress shielding in the calcar region. In the conventional anatomic cementless stem group, 22 hips (11%) showed Grade 1 stress shielding, 26 (13%) showed Grade 2 stress shielding, 92 (46%) showed Grade 3 stress shielding, and the remaining 60 (30%) showed Grade 4 stress shielding (Table 2).
BMD was greater in the ultrashort stem group than in the conventional stem group. In the ultrashort stem group, the BMD increased in Zone 1 at each followup but slightly decreased in Zone 7. In the conventional stem group, BMD in Zones 1 and 7 was decreased at each followup. BMD in the Zone 1 at 12 years followup was 3.29 ± 0.28 g/cm2 in the ultrashort stem group and 1.88 ± 0.18 g/cm2 in the conventional stem group (p = 0 .021), BMD in the Zone 7 at 11.8 years followup was 2.97 ± 0.25 g/cm2 in the ultrashort stem group and 0.91 ± 0.09 g/cm2 in the conventional stem group (p = 0.001) (Table 3).
One patient in each group underwent revision surgery. One patient in the ultrashort stem group underwent revision surgery for an unstable stem after a fall. The patient had implantation of an Anatomical Medullary Locking (AML®) cementless stem (DePuy) (Fig. 4), however another patient refused revision surgery (Fig. 5). One patient in the conventional stem group had an unstable stem and underwent revision surgery with implantation of a larger Profile® stem. With the numbers available, we detected no difference between the study groups in terms of the proportion of hips that underwent revision (one hip [0.5%] in each group; same hazard by a mean factor of 1.19; 95% CI, 0.81–2.81).
Discussion
There are few short-term studies of the ultrashort stem [17, 19, 21, 22, 34], and to our knowledge well-designed randomized controlled long-term studies regarding the performance of ultrashort and conventional stems in the same patients have not been published. We therefore sought to compare ultrashort and conventional anatomic cementless stems in the same patients to document the long-term performance of both stems. We found no differences in patient-reported outcome scores, slight benefits favoring the short stem in terms of thigh pain which was more common in the conventional stem group, but it generally was mild. Harris hip scores and BMD were not different between the groups. There were no differences between the stems in terms of fixation or the likelihood of revision surgery at a minimum followup of 10 years.
This study has some limitations. First, because of the ceiling effects of the scores used, our ability was limited to differentiate the outcomes between the two groups. However, we obtained similar excellent results in both groups. Second, the high incidence of the primary diagnosis of osteonecrosis combined with the low BMI (29.6 kg/m2) may limit the populations to which this study applies. However, the active and younger patients in our study group were good candidates for studying both stems. Third, we did not evaluate interobserver variability to ensure consistency in interpreting hip scores and radiographic and BMD findings. However, the chance-corrected kappa coefficient for intraobserver agreement ranged from 0.95 to 1.00, indicating excellent reproducibility of the measurements. Fourth, the outcomes of 12 patients who were lost to followup are unknown. Finally, evaluating longitudinal changes in BMD during the DEXA examination of the different prosthetic designs can be problematic. Minor changes in femoral rotation or patient position can lead to a 5% precision error by altering the area of the medial femoral cortex [28]. Therefore, there may be a potential bias in interpretation of the DEXA results.
We found favorable clinical results in both groups, including the Harris hip score and the WOMAC score, and these results are comparable to those of previous studies [10, 17–19, 35]. Studies support the idea that the ultrashort stem relieves pain and restores function comparable to conventional stems at short- and long-term followup [10, 17, 19, 35]. Thigh pain is believed to be related to stem design and implant stiffness [3, 5, 6, 9, 24, 30, 37]. The normal modulus of elasticity of cortical bone is less than 20 GPa [5], whereas most conventional metal implants occupying the diaphysis have a modulus of elasticity between 80 and 200 GPa [30, 37]; therefore, an ultrashort or tapered, polished intramedullary stem is one way to preserve femoral elasticity and avoid thigh pain. The absence of thigh pain in all but two patients in the ultrashort stem group may be attributed to rigid axial and torsional stability in the proximal femur and maintaining a normal modulus of elasticity in the diaphysis by absence of the distal stem. The two patients with severe (9 points) thigh pain in the ultrashort stem group had an unstable stem. In the conventional stem group, thigh pain might be attributed to the increase of the modulus of elasticity in the diaphysis by the presence of the distal stem.
A potential concern is whether an ultrashort stem will be sufficiently biomechanically stable to achieve durable bone ingrowth and whether longer-term clinical performance is maintained [17, 21, 22, 34]. Walker et al. [39], based on biomechanical testing, suggested that an ultrashort stem is sufficient if the stem has lateral flare. Santori and Santori [34] reported solid fixation of their custom-made ultrashort stem at a mean 8 years followup. Between 3½ and 7½ years followup, Kim et al. [16, 17, 19, 21, 22] reported firm fixation of the Proxima™ ultrashort stem. On the basis of their findings, torsional stability of the ultrashort stem can be provided without diaphyseal fixation by preservation of the femoral neck and lateral flare of the femoral component. In the current study, we observed that the performance of the ultrashort stem in our younger patients was comparable to that of the conventional cementless stems.
The Profile® conventional anatomic femoral stem used in the current study is designed for metaphyseal and diaphyseal fixation. To establish proximal load transfer, the proximal 1/3 of the stem was porous coated and the distal stem had a matte surface. Although Kim et al. [20] reported stable fixation radiographically after a minimum 8 years followup, cortical thinning and atrophy of the proximal femur was observed in all hips, indicating distal load transfer (Fig. 6). Our results are consistent with those of the previous study by Kim et al. [20]. Results of the DEXA examination showed that BMD increased in Zone 1, but slightly decreased in Zone 7 in the ultrashort stem group and decreased in Zones 1 and 7 in the conventional stem group. These findings are consistent with those of a previous study [20]. In that study, BMD in the ultrashort stem group was reported to have increased in Zone 1 at 3 years after the surgery, but slightly decreased in Zone 7. In the conventional stem group, BMD decreased in Zones 1 and 7. Findings of the BMD signify that the ultrashort stem had a predominantly proximal load transfer and that the conventional stem had a predominantly distal load transfer. This phenomenon may lead to further proximal femoral bone loss in the conventional stem group with longer-term followup.
We found no difference in the proportion of stems in each group that underwent revision, and the overall percentage of hips that were revised in both groups compared favorably with percentages reported by others [28, 29, 34–36]. Although results of previous reports of short stems [16, 17, 21, 22, 26, 27, 31, 32] were good, the followup periods in those series were short. Results of our current study showed that the survival rate of the ultrashort stem had equivalent survival rates to the conventional stem at mean followup of 12 years.
When choosing a femoral stem, the surgeon should aim for optimal distribution of stress in the proximal femur, for maximal preservation of bone without compromising stability and for long-lasting fixation. At followup into the second decade, ultrashort stems showed no differences from conventional cementless stems in terms of validated outcomes scores or fixation, while showing slightly less stress shielding and less thigh pain, although this difference may not have been clinically important; in the conventional group, thigh pain was mostly mild, and there were no differences in hip scores. Reduction of stress shielding may reduce the long-term risk of periprosthetic fracture, but this was not shown here. Future studies might document the reduction of the long-term risk of periprosthetic fracture by reduction of stress shielding.
References
Aldinger PR, Breusch SJ, Lukoschek M, Mau H, Ewerbeck V, Thomsen M. A ten-to 15-year follow-up of the cementless Spotorno stem. J Bone Joint Surg Br. 2003;85:209–214.
Bellamy N, Buchanan WW, Goldsmith CH, Campbell J, Stitt LW. Validation study of WOMAC: a health status instrument for measuring clinically important patient relevant outcomes to antirheumatic drug therapy in patients with osteoarthritis of the hip or knee. J Rheumatol. 1988;15:1833–1840.
Bourne RB, Rorabeck CH, Ghazal ME, Lee MH. Pain in the thigh following total hip replacement with a porous-coated anatomic prosthesis for osteoarthrosis: a five-year follow-up study. J Bone Joint Surg Am. 1994;76:1464–1470.
Braud P, Freeman MA. The effect of retention of the femoral neck and of cement upon the stability of proximal femoral prosthesis. J Arthroplasty. 1990; 5(suppl):S5–10.
Brown TE, Larson B, Shen F, Moskal JT. Thigh pain after cementless total hip arthroplasty: evaluation and management. J Am Acad Orthop Surg. 2002;10:385–392.
Callaghan JJ, Dysart SH, Savory CG. The uncemented porous-coated anatomic total hip prosthesis: two-year results of a prospective consecutive series. J Bone Joint Surg Am 1988;70:337–346.
Capello WN, D`Antonio JA, Jaffe WL, Geesink RG, Manley MT, Feinberg JR. Hydroxyapatite-coated femoral components: 15-year minimum followup. Clin Orthop Relat Res. 2006;453:75–80.
Dorr LD. Total hip replacement using APR system. Tech Orthop. 1986;1:22–34.
Engh CA, Bobyn JD. The influence of stem size and extent of porous coating on femoral bone resorption after primary cementless hip arthroplasty. Clin Orthop Relat Res. 1988;231:7–28.
Engh CA, Massin P, Suthers KE. Roentgenographic assessment of the biologic fixation of porous-surfaced femoral components. Clin Orthop Relat Res. 1990;257:107–128.
Glassman AH, Bobyn JD, Tanzer M. New femoral designs: do they influence stress shielding? Clin Orthop Relat Res. 2006;453:64–74.
Grubl A, Chiari C, Gruber M, Kaider A, Gottsauner-Wolf F. Cementless total hip arthroplasty with a tapered, rectangular titanium stem and a threaded cup: a minimum ten-year follow-up. J Bone Joint Surg Am. 2002;84:425–431.
Harris WH. Traumatic arthritis of the hip after dislocation and acetabular fractures: treatment by mold arthroplasty. An end-results study using a new method of results evaluation. J Bone Joint Surg Am. 1969;51:737–755.
Hartzband MA, Glassman AH, Goldberg VM, Jordan LR, Crowninshield RD, Fricka KB, Jordan LC. Survivorship of a low-stiffness extensively porous-coated femoral stem at 10 years. Clin Orthop Relat Res. 2010;468:433–440.
Hennessy DW, Callaghan JJ, Liu SS. Second generation extensively porous coated THA stems at minimum 10-year followup. Clin Orthop Relat Res. 2009;467:2290–2296.
Kim YH, Choi YW, Kim JS. Comparison of bone mineral density changes around short, metaphyseal-fitting, and conventional cementless anatomical femoral components. J Arthroplasty. 2011;26:931–940.
Kim YH, Kim JS, Joo JH, Park JW. A prospective short-term outcome study of a short metaphyseal fitting total hip arthroplasty. J Arthroplasty. 2012;27:88–94.
Kim YH, Kim JS, Park JW, Joo JH. Contemporary total hip arthroplasty with and without cement in patients with osteonecrosis of the femoral head: a concise follow-up, at an average of seventeen years of a previous report. J Bone Joint Surg Am. 2011;93:1806–1810.
Kim YH, Oh JH. A comparison of a conventional versus a short, anatomical metaphyseal-fitting cementless femoral stem in the treatment of patients with a fracture of the femoral neck. J Bone Joint Surg Br. 2012;94:774–781.
Kim YH, Oh SH, Kim JS. Primary total hip arthroplasty with a second-generation cementless total hip prosthesis in patients younger than fifty years of age. J Bone Joint Surg Am. 2003;85:109–114.
Kim YH, Park JW, Kim JS. Behavior of the ultra-short anatomic cementless femoral stem in young and elderly patients. Int Orthop. 2013;37:2323–2330.
Kim YH, Park JW, Kim JS. Is diaphyseal stem fixation necessary for primary total hip arthroplasty in patients with osteoporotic bone (class C bone)? J Arthroplasty. 2013;28:139–146.
Kim YH, Park JW, Kim JS. Metaphyseal engaging short and ultra-short anatomic cementless stem in young and active patients. J Arthroplasty. 2016;31:180–185.
Kim YH, Park JW, Kim JS, Kim IW. Twenty-five to twenty-seven-year results of a cemented vs a cementless stem in the same patients younger than 50 years of age. J Arthroplasty. 2016; 31: 662–667.
Landis JR, Koch GG. The measurement of observer agreement for categorical data. Biometrics. 1977;33:159–174.
Meding JB, Galley MR, Ritter MA. High survival of uncemented proximally porous-coated titanium alloy femoral stems in osteoporotic bone. Clin Orthop Relat Res. 2010;468:441–447.
Morrey BF, Adams RA, Kessler M. A conservative femoral replacement for total hip arthroplasty: a prospective study. J Bone Joint Surg Br. 2000;82:952–958.
Mortimer ES, Rosenthall L, Paterson I, Bobyn JD. Effect of rotation on periprosthetic bone mineral measurements in a hip phantom. Clin Orthop Relat Res. 1996;324:269–274.
Nourbash PS, Paprosky WG. Cementless femoral design concerns: rationale for extensive porous coating. Clin Orthop Relat Res. 1998;355:189–199.
Φstbyhaug PO, Klaksvik J, Romundstad P, Aamodt A. An in vitro study of the strain distribution in human femora with anatomical and customised femoral stems. J Bone Joint Surg Br. 2009;91:676–682.
Patel RM, Lo WM, Cayo MA, Dolan MM, Stulberg SD. Stable, dependable fixation of short-stem femoral implants at 5 years. Orthopedics. 2013;36:e301–307.
Pipino F, Molfetta L, Grandizio M. Preservation of the femoral neck in hip arthroplasty: results of a 13-to 17-year follow-up. J Orthop Traumatol. 2000;1:31–39.
Rajarathnam SS, Jack C, Tavakkolizadeh A, George MD, Fletcher RJ, Hankins M, Shepperd JA. Long-term results of a hydroxyapatite-coated femoral component in total hip replacement: a 15-to 21-year follow-up study. J Bone Joint Surg Br. 2008;90:27–30.
Santori FS, Santori N. Mid-term results of a custom-made short proximal loading femoral component. J Bone Joint Surg Br. 2010;92:1231–1237.
Schramm M, Keck F, Hohmann D, Pitto RP. Total hip arthroplasty using an uncemented femoral component with taper design: outcome at 10-years follow-up. Arch Orthop Trauma Surg. 2000;120:407–412.
Sugiyama H, Whiteside LA, Kaiser AD. Examination of rotational fixation of the femoral component in total hip arthroplasty. Clin Orthop Relat Res. 1989;249:122–128.
Sumner DR, Galante JO. Determinants of stress shielding: design versus materials versus interface. Clin Orthop Relat Res. 1992;274:202–212.
Vresilovic EJ, Hozack WJ, Rothman RH. Incidence of thigh pain after uncemented total hip arthroplasty as a femoral stem size. J Arthroplasty. 1996;11:304–311.
Walker PS, Culligan SG, Hua J, Muirhead-Alwood SK, Bentley G. The effect of a lateral flare feature on uncemented hip stems. Hip Int. 1999;9:71–80.
Whiteside LA, Easley JC. The effect of collar and distal stem fixation on micromotion of the femoral stem in uncemented total hip arthroplasty. Clin Orthop Relat Res. 1989;239:145–153.
Whiteside LA, White SE, McCarthy DS. Effect of neck resection on torsional stability of cementless total hip replacement. Am J Orthop. 1995;24:766–770.
Zahiri CA, Schmalzried TP, Szuszczewicz ES, Amstutz HC. Assessing activity in joint replacement patients. J Arthroplasty. 1998;13:890–895.
Zicat B, Engh CA, Gokcen E. Patterns of osteolysis around total hip components inserted with and without cement. J Bone Joint Surg Am. 1995;77:432–439.
Acknowledgments
We thank to Doo-Ri Kim MA (research associate, The Joint Replacement Center, Ewha Womans University SeoNam Hospital) for collecting and analyzing the clinical, radiographic, and BMD data.
Author information
Authors and Affiliations
Corresponding author
Additional information
Each author certifies that he or she, or a member of his or her immediate family, has no funding or commercial association (eg, consultancies, stock ownership, equity interest, patent/licensing arrangements, etc) that might pose a conflict of interest in connection with the submitted article.
All ICMJE Conflict of Interest Forms for authors and Clinical Orthopaedics and Related Research ® editors and board members are on file with the publication and can be viewed on request.
Clinical Orthopaedics and Related Research ® neither advocates nor endorses the use of any treatment, drug, or device. Readers are encouraged to always seek additional information, including FDA-approval status, of any drug or device prior to clinical use.
Each author certifies that his or her institution approved the human protocol for this investigation, that all investigations were conducted in conformity with ethical principles of research, and that informed consent for participation in the study was obtained.
About this article
Cite this article
Kim, YH., Park, JW. & Kim, JS. Ultrashort versus Conventional Anatomic Cementless Femoral Stems in the Same Patients Younger Than 55 Years. Clin Orthop Relat Res 474, 2008–2017 (2016). https://doi.org/10.1007/s11999-016-4902-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11999-016-4902-4