Abstract
Mechanical properties and microstructure of Al-Mg-(Sc, Zr) welded joint prepared by manual labor melt inert gas(MIG) welding method using Al-Mg and Al-Mg-Sc weld wire as filling materials were studied comparatively. The results show that the apparent recrystallization does not happen in heat-affected zone. It proves that Al-Mg(Sc,Zr) alloy has a high capability of resistance to weldiing heat-soften. Using Al-Mg-Sc welding wire as filling material can obviously refine the grains of weld seam and improve its strength. The layer of small equal-axe grains in fusion area improves the joint strength between welded metal and base metal. The coefficients of welded joints when Al-Mg-Sc and Al-Mg weldiong wire are used as filling material are greater than 0.90, respectively. The yield strength of welded joints with Al-Mg welding wire is only 187 MPa, one is as 287 MPa with Al-Mg-Sc welding wire, thus the working strength of the welded unit is greatly improved.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
JIANG Feng, YIN Zhi-min, HUANG Bai-yun, et al. Homogenization and recrystallization of Al-6Mg alloys with and without Sc and Zr[J]. Journal of Rare Earths, 2004, 22(5): 600–603.
JIANG Feng, YIN Zhi-min, HUANG Bai-yun, et al. Micro-alloying principle of minor scandium in aluminum alloys and its effects on properties of alloys[A]. 2004 International Conference on Rare Earth Research and Application (ICRERA-2004)[C]. Baotou: August 8–12, 2004.
YIN Zhi-min, JIANG Feng, PAN Qing-lin, et al. Microstructures and mechanical properties of Al-Mg and Al-Zn-Mg based alloys containing minor scandium and zirconium[J]. Transactions Nonferrous Metals Society of China, 2003, 13(3): 515–520.
YIN Zhi-min, PEN Qing-lin, ZHANG Yong-hong, et al. Effect of minor Sc and Zr on the microstructure and mechanical properties of Al-Mg based alloys[J]. Mater Sci and Eng A, 2000, 280(1):151–155.
Malinkina T I, Markachev N A, Kovtun V A, et al. Welded structures of 01570 aluminium alloy[J]. Welding International, 1998, 12(7): 566–569.
Yelagin V I, Zakhanov V V, Rostova T D. Aluminum alloys alloying with scandium [J]. Metal Sci Heat Treat, 1983, 25: 546.
LI Zhao-lu, PAN Qing-lin, CHEN Xian-ming. Effect of minor Sc and Ti on microstructures and mechanical properties of Al- Mg based alloys[J]. Material Science and Engineering of Weapon, 2003, 26(1): 11–15. (in Chinese)
PAN Qing-lin, YIN Zhi-min, ZHANG Chuan-fu, Effect of minor Sc and Zr on microstructures and mechanical properties of Al- Mg based alloys[J]. Transaction of Aerial Material, 2002, 22(1): 6–10. (in Chinese)
LIN De-chao, HE Yong, HE Yun-jia, et al. Analysis of microstructure characteristic in the fusion zone of Al-Li alloy welded seam[J]. Mechannical Engineering Material, 1996(4): 10–12. (in Chinese)
Flemings M C, Solidification Processing[M]. New York: Mc Graw Hill, 1974.
TANG Ren-zheng. Physical Metallurgy[M]. Beijing: Metallurgical Industry Press, 1997. (in Chinese)
YIN Zhi-min, ZHU Da-peng, JIANG Feng. Recrystallization of Al-Mg-Mn and Al-Mg-Mn-Sc-Zr alloys [J]. Journal of Material Engineering, 2004(6): 3–6. (in Chinese)
Author information
Authors and Affiliations
Corresponding author
Additional information
Foundation item: Project (2003AA305020) supported by the Postdoctoral Science Foundation of China; project supported by the National High Technology Research and Development Program of China
Rights and permissions
About this article
Cite this article
Jiang, F., Chen, Sl., Huang, By. et al. Microstructure and properties of Al-Mg-(Sc, Zr) welded joint. J Cent. South Univ. Technol. 12 (Suppl 1), 23–27 (2005). https://doi.org/10.1007/s11771-005-0365-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11771-005-0365-6