Abstract
The curved steel-concrete-steel (SCS) sandwich shell was recently proposed to resist blast loading and it showed better blast resistant performance as compared to flat SCS sandwich shell via developing compressive force along the shell. In this paper, a dimensionless Pressure-Impulse (P-I) diagram was constructed as a convenient tool to predict the damage level of curved SCS sandwich shell subjected to uniformly distributed blast loading. The curved SCS sandwich shell was equivalent to a single-degree-of-freedom (SDOF) system and the equation of motion was established by employing the Lagrange’s equation. To construct the dimensionless P-I diagram, the energy balance method was utilized to yield the pressure and impulse asymptotes and the responses in the dynamic response regime were obtained via employing the SDOF method. Then, the finite element method was employed to validate the developed dimensionless P-I diagram. Finally, the procedures of using the constructed dimensionless P-I diagram to quickly conduct the blast resistant design of curved SCS sandwich shell were presented.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Oduyemi T O S, Wright H D. An experimental investigation into the behavior of double skin sandwich beams. Journal of Constructional Steel Research, 1989, 14(3): 197–220
Malek N, Machida A, Mutsuyoshi H, Makabe T. Steel-concrete sandwich members without shear reinforcement. Transactions of the Japan Concrete Institute, 1993, 15(2): 1279–1284
Foundoukos N. Behavior and design of steel-concrete-steel sandwich construction. Thesis for the Doctoral Degree. London: University of London, 2005
Huang Z, Liew J Y R. Structural behaviour of steel-concrete-steel sandwich composite wall subjected to compression and end moment. Thin-walled Structures, 2016, 98: 592–606
Yan J B, Liew J Y R, Zhang M H. Tensile resistance of J-hook connectors used in Steel-Concrete-Steel sandwich structure. Journal of Constructional Steel Research, 2014, 100: 146–162
Liew J Y R, Sohel K M A, Koh C G. Impact tests on steel-concrete-steel sandwich beams with lightweight concrete core. Engineering Structures, 2009, 31(9): 2045–2059
Remennikov A M, Kong S Y. Numerical simulation and validation of impact response of axially-restrained steel-concrete-steel sandwich panels. Composite Structures, 2012, 94(12): 3546–3555
Anandavalli N, Lakshmanan N, Rajasankar J, Parkash A. Numerical studies on blast loaded steel-concrete composite panels. JCES, 2012, 1(3): 102–108
Wang Y, Liew J Y R, Lee S C. Theoretical models for axially restrained steel-concrete-steel sandwich panels under blast loading. International Journal of Impact Engineering, 2015, 76: 221–231
Crawford J E, Lan S. Blast barrier design and testing. In: Proceedings of the ASCE Structures Congress, St. Louis, Missour, 2006
Liew J Y R, Wang T Y. Novel steel-concrete-steel sandwich composite plates subjected to impact and blast load. Advances in Structural Engineering, 2011, 14(4): 673–687
Lan S, Lok T S, Heng L. Composite structural panels subjected to explosive loading. Construction & Building Materials, 2005, 19(5): 387–395
Wang Y, Liew J Y R, Lee S C. Experimental and numerical studies of non-composite Steel-Concrete-Steel sandwich panels under impulsive loading. Materials & Design, 2015, 81: 104–112
Wang Y, Zhai X, Lee S C, Wang W. Responses of curved steel-concrete-steel sandwich shells subjected to blast loading. Thinwalled Structures, 2016, 108: 185–192
Yan J B, Liew J Y R, Zhang M H, Sohel K M A. Experimental and analytical study on ultimate strength behavior of steel-concrete-steel sandwich composite beam structures. Materials and Structures, 2015, 48(5): 1523–1544
Yan J B, Liew J Y R, Zhang M H, Li Z X. Punching shear resistance of steel-concrete-steel sandwich composite shell structure. Engineering Structures, 2016, 117: 470–485
Yan J B, Xiong MX, Qian X, Liew J Y R. Numerical and parametric study of curved steel-concrete-steel sandwich composite beams under concentrated loading. Materials and Structures, 2016, 49(10): 3981–4001
Yan J B, Richard Liew J Y, Qian X, Wang J Y. Ultimate strength behavior of curved Steel-Concrete-Steel sandwich composite beams. Journal of Constructional Steel Research, 2015, 115: 316–328
Huang Z, Liew J Y R. Nonlinear finite element modeling and parametric study of curved steel-concrete-steel double skin composite panels infilled with ultra-lightweight cement composite. Construction & Building Materials, 2015, 95: 922–938
Huang Z Y, Wang J Y, Richard Liew J Y, William Marshall P. Lightweight steel-concrete-steel sandwich composite shell subject to punching shear. Ocean Engineering, 2015, 102: 146–161
Biggs J M. Introduction to Structural Dynamics. New York: McGraw-Hill, 1964
Wang Y, Xiong M X. Analysis of axially restrained water storage tank under blast loading. International Journal of Impact Engineering, 2015, 86: 167–178
Rigby S E, Tyas A, Bennett T. Elastic-plastic response of plates subjected to cleared blast loads. International Journal of Impact Engineering, 2014, 66: 37–47
Morison C M. Dynamic response of walls and slabs by single-degree-of-freedom analysis-a critical review and revision. International Journal of Impact Engineering, 2006, 32(8): 1214–1247
Nassr A A, Razaqpur A G, Tait M J, Campidelli M, Foo S. Single and multi degree of freedom analysis of steel beams under blast loading. Nuclear Engineering and Design, 2012, 242(1): 63–77
Carta G, Stochino F. Theoretical models to predict the flexural failure of reinforced concrete beams under blast loads. Engineering Structures, 2013, 49: 306–315
Krauthammer T, Bazeos N, Holmquist T J. Modified SDOF analysis of box-type structures. Journal of Structural Engineering, 1986, 112(4): 726–744
Astarlioglu S, Krauthammer T, Morency D, Tran T P. Behavior of reinforced concrete columns under combined effects of axial and blast-induced transverse loads. Engineering Structures, 2013, 55: 26–34
UFC 3-340-02. Structures to Resist the Effects of Accidental Explosions. Washington, D.C.: US Department of Army, Navy and the Air Force, 2008
ASCE. Design of Blast-Resistant Buildings in Petrochemical Facilities. American Society of Civil Engineers, 2010
ASCE. Blast Protection of Buildings. ASCE/SEI 59-11. American Society of Civil Engineers, 2011
Mays G, Smith P D. Blast Effects on Buildings: Design of Buildings to Optimize Resistance to Blast Loading. London: T. Telford, 1995
Li Q M, Meng H. Pressure-impulse diagram for blast loads based on dimensional analysis and single-degree-of-freedom mode. Journal of Engineering Mechanics, 2002, 128(1): 87–92
Li Q M, Meng H. Pulse loading shape effects on pressure-impulse diagram of an elastic-plastic, single-degree-of-freedom structural model. International Journal of Mechanical Sciences, 2002, 44(9): 1985–1998
Fallah A S, Louca L A. Pressure-impulse diagrams for elastic-plastic-hardening and softening single-degree-of-freedom models subjected to blast loading. International Journal of Impact Engineering, 2007, 34(4): 823–842
Krauthammer T, Astarlioglu S, Blasko J, Soh T B, Ng P H. Pressure-impulse diagrams for the behaviour assessment of structural components. International Journal of Impact Engineering, 2008, 35(8): 771–783
Dragos J, Wu C. A new general approach to derive normalised pressure impulse curves. International Journal of Impact Engineering, 2013, 62: 1–12
Shi Y, Hao H, Li Z X. Numerical derivation of pressure-impulse diagrams for prediction of RC column damage to blast loads. International Journal of Impact Engineering, 2008, 35(11): 1213–1227
Mutalib A A, Hao H. Development of P-I diagrams for FRP strengthened RC columns. International Journal of Impact Engineering, 2011, 38(5): 290–304
Rabczuk T, Areias P M A, Belytschko T. A meshfree thin shell method for non-linear dynamic fracture. International Journal for Numerical Methods in Engineering, 2007, 72(5): 524–548
Nguyen-Thanh N, Zhou K, Zhuang X, Areias P, Nguyen-Xuan H, Bazilevs Y, Rabczuk T. Isogeometric analysis of large-deformation thin shells using RHT-splines for multiple-patch coupling. Computer Methods in Applied Mechanics and Engineering, 2017, 316: 1157–1178
Rabczuk T, Kim J Y, Samaniego E, Belytschko T. Homogenization of sandwich structures. International Journal for Numerical Methods in Engineering, 2004, 61(7): 1009–1027
Rabczuk T, Zi G, Bordas S, Nguyen-Xuan H. A geometrically nonlinear three-dimensional cohesive crack method for reinforced concrete structures. Engineering Fracture Mechanics, 2008, 75(16): 4740–4758
Rabczuk T, Zi G, Bordas S, Nguyen-Xuan H. A simple and robust three-dimensional cracking-particle method without enrichment. Computer Methods in Applied Mechanics and Engineering, 2010, 199(37–40): 2437–2455
Rabczuk T, Belytschko T. A three-dimensional large deformation meshfree method for arbitrary evolving cracks. Computer Methods in Applied Mechanics and Engineering, 2007, 196(29–30): 2777–2799
Hallquist J O. LS-DYNA Theory Manual. Livermore Software Technology Corporation (LSTC), 2006
Foundoukos N, Chapman J C. Finite element analysis of steel-concrete-steel sandwich beams. Journal of Constructional Steel Research, 2008, 64(9): 947–961
Clubley S K, Moy S S J, Xiao R Y. Shear strength of steel-concrete-steel composite panels. Part II—Detailed numerical modelling of performance. Journal of Constructional Steel Research, 2003, 59(6): 795–808
Li X, Chen J F, Lu Y, Yang Z. Modelling static and dynamic FRP-concrete bond behaviour using a local concrete damage model. Advances in Structural Engineering, 2015, 18(1): 45–58
Chen W, Hao H, Chen S. Numerical analysis of prestressed reinforced concrete beam subjected to blast loading. Materials & Design, 2015, 65: 662–674
Federal Highway Administration. Users Manual for LS-DYNA Concrete Material Model 159. Publication No. FHWA-HRT-05-062, 2007
Federal Highway Administration. Evaluation of LS-DYNA Concrete Material Model 159. Publication No. FHWA-HRT-05-063, 2007
Cowper G R, Symonds P S. Strain Hardening and Strain Rate Effects in the Impact Loading of Cantilever Beams. Applied Mathematics Report. 1958
Jones N. Structural Impact. Cambridge/New York: Cambridge University Press, 1988
Kang W K, Lee S C, Liew J Y R. Analysis of steel-concrete composite column subject to blast. Proceedings of the Institution of Civil Engineers. Structures and Buildings, 2013, 166(1): 15–27
Xie M, Foundoukos N, Chapman J C. Static tests on steel-concrete-steel sandwich beams. Journal of Constructional Steel Research, 2007, 63(6): 735–750
Dym C L, Williams H E. Stress and displacement estimates for arches. Journal of Structural Engineering, 2011, 137(1): 49–58
Baker W E, Cox P A, Westine P S, Kulesz J J, Strehlow R A. Explosion and Hazards and Evaluation. Amsterdam: Elsevier Scientific Publishing Compay, 1983
Eurocode 2. Design of concrete structures—part 1-1: General Rules and Rules for Buildings. EN 1992-1-1. London: British Standards Institution, 2004
Acknowledgements
The research presented in this paper was financially supported by the National Natural Science Foundation of China (Grant No. 51608151), the China Postdoctoral Science Foundation (Nos. 2017T100245, 2016M600252), Heilongjiang Postdoctoral Fund (No. LBH-Z16063) and the Fundamental Research Funds for the Central Universities (No. HIT. NSRIF.2019069).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wang, Y., Zhai, X. Development of dimensionless P-I diagram for curved SCS sandwich shell subjected to uniformly distributed blast pressure. Front. Struct. Civ. Eng. 13, 1432–1445 (2019). https://doi.org/10.1007/s11709-019-0566-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11709-019-0566-y