Abstract
Several international legislations recently banned the use of Pb because of environmental concerns. The eutectic Sn-Ag solder is one of the promising candidates to replace the conventional Sn-Pb solder primarily because of its excellent mechanical properties. In this study, interfacial reaction of the eutectic Sn-Ag and Sn-Pb solders with Ni/Cu under-bump metallization (UBM) was investigated with a joint assembly of solder/Ni/Cu/Ti/Si3N4/Si multilayer structures. After reflows, only one (Ni,Cu)3Sn4 intermetallic compound (IMC) with faceted and particlelike grain feature was found between the solder and Ni. The thickness and grain size of the IMC increased with reflow times. Another (Cu,Ni)6Sn5 IMC with a rod-type grain formed on (Ni,Cu)3Sn4 in the interface between the Sn-Pb solder and the Ni/Cu UBM after more than three reflow times. The thickness of the (Ni,Cu)3Sn4 layer formed in the Sn-Pb system remained almost identical despite the numbers of reflow; however, the amounts of (Cu,Ni)6Sn5 IMC increased with reflow times. Correlations between the IMC morphologies, Cu diffusion behavior, and IMC transformation in these two solder systems will be investigated with respect to the microstructural evolution between the solders and the Ni/Cu UBM. The morphologies and grain-size distributions of the (Ni,Cu)3Sn4 IMC formed in the initial stage of reflow are crucial for the subsequent phase transformation of the other IMC.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
K.S. Bae and S.J. Kim, J. Mater. Res. 17, 743 (2002).
H.W. Miao and J.G. Duh, Mater. Chem. Phys. 71, 255 (2001).
D.R. Frear, J.W. Jang, J.K. Lin, and C. Zang, JOM 53, 28 (2001).
B.L. Young, J.G. Duh, and B.S. Chiou, J. Electron. Mater. 30, 543 (2001).
M. McCormack, S. Jin, G.W. Kammlott, and H.S. Chen, Appl. Phys. Lett. 63, 15 (1993).
J.H. Lau, Flip Chip Technologies (New York: McGraw-Hill, 1996).
G.R. Blackwell, The Electronic Packaging Handbook (Boca Raton, FL: CRC Press, 2000), pp. 4.4–4.25.
A.A. Liu, H.K. Kim, K.N. Tu, and P.A. Totta, J. Appl. Phys. 80, 2774 (1996).
D.R. Frear, F.M. Hosking, and P.T. Vianco, Proc. Materials Developments in Microelectronic Packaging Conf. (Materials Park, OH: ASM International, 1991), pp. 229–240.
R.G. Werner, D.R. Frear, J. DeRosa, and E. Sorongon, 1999 Int. Symp. on Advanced Packaging Materials (Piscataway, NJ: IEEE, 1999), pp. 246–251.
C.S. Huang, J.G. Duh, Y.M. Chen, and J.H. Wang, J. Electron. Mater. 32, 89 (2003).
C.S. Huang and J.G. Duh, J. Mater. Res. 18, 935 (2003).
J.Y. Park, C.W. Yang, J.S. Ha, C.U. Kim, E.J. Kwon, S.B. Jung, and C.S. Kang, J. Electron. Mater. 30, 1165 (2001).
W.K. Choi and H.M. Lee, J. Electron. Mater. 28, 1251 (1999).
J.I. Goldstein, Scanning Electron Microscopy and X-ray Microanalysis (New York: Plenum Press, 1992), pp. 306–330.
W.H. Tao, C. Chen, C.E. Ho, W.T. Chen, and C.R. Kao, Chem. Mater. 13, 1051 (2001).
W.K. Choi, S.Y. Jang, J.H. Kim, K.W. Paik, and H.M. Lee, J. Mater. Res. 17, 597 (2002).
M. Li, F. Zhang, W.T. Chen, K. Zeng, K.N. Tu, H. Balkan, and P. Elenius, J. Mater. Res. 17, 1612 (2002).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Huang, CS., Duh, JG. & Chen, YM. Metallurgical reaction of the Sn-3.5Ag solder and Sn-37Pb solder with Ni/Cu under-bump metallization in a flip-chip package. J. Electron. Mater. 32, 1509–1514 (2003). https://doi.org/10.1007/s11664-003-0122-2
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/s11664-003-0122-2