Abstract
The effect of filler alloys C-263, RENÉ-41, IN-718, and FM-92 on heat-affected zone (HAZ) cracking susceptibility of cast IN-738 LC, which is a high-temperature Ni-based superalloy used at temperatures up to 980 °C and is precipitation hardened by the γ′ (Ni3Al,Ti) phase, by gas-tungsten-arc (GTA) welding was studied. In addition, autogenous welds were also made on the IN-738 parent material. The preweld treatments consisted of the standard solution treatment at 1120 °C for 2 hours followed by air cooling, and a new heat treatment, which was developed to improve the HAZ cracking resistance of IN-738 LC. This heat treatment consisted of solution treating at 1120 °C followed by air cooling then aging at 1025 °C for 16 hours followed by water quenching. Welds were observed to suffer intergranular HAZ cracking, regardless of the filler alloy; however, the autogenous welds were most susceptible to HAZ cracking. In general, the cracking tendency for both heat treatments was maximum for C-263 and RENE-41 fillers and decreased with the use of FM-92 and IN-718 filler alloys. The HAZ cracking was associated mainly with constitutional liquation of γ′ and MC carbides. On some cracks, liquated low melting point containing Zr-carbosulfide and Cr-Mo borides were also observed to be present. The cooling portion of the weld thermal cycle induced precipitation hardening via γ′ phase in the γ matrix of the weld metal. The HAZ cracking increased as the weld metal lattice mismatch between γ′ precipitates and γ matrix of the weld and its hardness (Ti + Al) increased. However, the weld-metal solidus and solidification temperature range, determined by high-temperature differential scanning calorimetry, did not correlate with the HAZ cracking susceptibility. It is suggested that the use of filler alloys with small γ′-γ lattice mismatch and slow age-hardening response would reduce the HAZ cracking in IN-738 LC superalloy welds.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
W. Lin, J.C. Lippold, and W.A. Baeslack III: Welding Res. Suppl., 1993, Apr., pp. 135s–153s.
D.S. Duvall and W.A. Owczarski: Welding J., 1967, Sept., pp. 423s–432s.
R. Thamburaj, W. Wallace, and J.A. Goldak: Int. Mater. Rev., 1983, vol. 28, (1), pp. 1–22.
O.A. Ojo, N.L. Richards, and M.C. Chaturvedi: Scripta Mater., 2004, vol. 50, pp. 641–46.
A.K. Koul and R. Thamburaj: Metall. Trans. A, 1985, vol. 16A, pp. 17–26.
A. Thakur, N.L. Richards, and M.C. Chaturvedi: Int. J. Joining Mater., 2003, vol. 15 (4), pp. 21–25.
B. Jahnke: Welding Res. Suppl., 1982, Nov., pp. 343s–347s.
H. van Esch and W. Greaves: ASM Int., 1998, Oct., pp. 130–37.
P. Lowden, C. Pilcher, and J. Liburdi: Proc. Int. Conf. on Gas Turbines and Aeroengine Congr. and Expo., Orlando, FL, June 3–6, 1991, The American Society of Mechanical Engineers, New York, NY, 1991, pp. 303–13.
C.Y. Su, C.P. Chou, B.C. Wu, and W.C. Lih: J. Mater. Eng. Performance, 1997 vol. 6 (5), pp. 619–27.
W.F. Savage and J.J. Pep: Welding J., Res. Suppl., 1967, vol. 46 (9), pp. 411s-422s.
W.A. Owczarski, D.S. Duvall, and C.P. Sullivan: Welding Res. Suppl., 1966, Apr., pp. 145s–155s.
B. Radhakrishnan and R.G. Thompson: Metall. Trans. A, 1991, vol. 22A, pp. 887–902.
D.F. Lahrman, R.D. Field, R. Darolin, and H.L. Fraser: Acta Metall., 1988, vol. 36 (5), pp. 1309–20.
B.H. Yoon, Y.S. Ahn, and C.H. Lee: Iron Steel Inst. Jpn. Int., 2002, vol. 42 (2), pp. 178–83.
J.C. Lippold, W.A. Baeslack III, and I. Varol: Welding Res. Suppl., 1992, Jan., pp. 1s–7s.
R.E. Pease: Welding J., Res. Suppl., 1957, vol. 36, pp. 330s-334s.
K. Saito, M. Aoki H. Kondo, and N. Ikeda: Iron Steel Inst. Jpn. Int., 1987, pp. 664–72.
D.S. Duvall and W.A. Owczarski: Welding Res., 1967, vol. 32, pp. 423s-432s.
W.A. Owczarski: Welding Res. Council, 1969, pp. 6–23.
T.J. Kelly: Welding J., 1989, vol. 68, pp. 44s-51s.
J.C. Borland and R.N. Younger: Br. Welding J., Res. Suppl., 1960, Jan., pp. 22–59.
H.L. Eiselstein: Am. Soc. Testing Mater., Tech. Pub., 1965, No. 369, pp. 62–79.
M.C. Chaturvedi: University of Manitoba, Winnipeg, unpublished research, 2004.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Banerjee, K., Richards, N.L. & Chaturvedi, M.C. Effect of filler alloys on heat-affected zone cracking in preweld heat-treated IN-738 LC gas-tungsten-arc welds. Metall Mater Trans A 36, 1881–1890 (2005). https://doi.org/10.1007/s11661-005-0051-1
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-005-0051-1