Abstract
X-ray based residual stress measurements were made on type 316 stainless steel and Fe3Al coatings that were high-velocity oxy-fuel (HVOF) sprayed onto low-carbon and stainless steel substrates. Nominal coating thicknesses varied from 250 to 1500 µm. The effect of HVOF spray particle velocity on residual stress and deposition efficiency was assessed by preparing coatings at three different torch chamber pressures. The effect of substrate thickness on residual stress was determined by spraying coatings onto thick (6.4 mm) and thin (1.4 mm) substrates. Residual stresses were compressive for both coating materials and increased in magnitude with spray velocity. For coatings applied to thick substrates, near-surface residual stresses were essentially constant with increasing coating thickness. Differences in thermal expansion coefficient between low-carbon and stainless steels led to a 180 MPa difference in residual stress for Fe3Al coatings. Deposition efficiency for both materials is maximized at an intermediate (∼600 m/s) velocity. Considerations for X-ray measurement of residual stresses in HVOF coatings are also presented.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
G.W. Goward: Mater. Sci. Technol., 1986, vol. 2, pp. 194–200.
L. Pejryd, J. Wigren, D.J. Greving, J.R. Shadley, and E.F. Rybicki: J. Thermal Spray Technol., 1995, vol. 4, pp. 268–74.
T.C. Totemeier, R.N. Wright, and W.D. Swank: Metall. Mater. Trans. A, 2003, vol. 34A, pp. 2223–231.
M. Kramer, O. Degirmen, A.J. Thom, and M. Akinc: Paper presented at 15th Annual Conf. on Fossil Energy Materials, Knoxville, TN, 2001.
T.C. Totemeier, R.N. Wright, and W.D. Swank: J. Thermal Spray Technol., 2002, vol. 11, pp. 400–08.
T.C. Totemeier and J.E. King: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 353–62.
R.T.R. McGrann, D.J. Greving, J.R. Shadley, E.F. Rybicki, T.L. Kruecke, and B.E. Bodger: Surface Coatings Technol., 1998, vols. 108–109, pp. 59–64.
S.J. Howard, Y.C. Tsui, and T.W. Clyne: in 1994 Thermal Spray Industrial Applications, C.C. Berndt and S. Sampath, eds., ASM INTERNATIONAL, Materials Park, OH, 1994, pp. 703–08.
S. Kuroda, T. Fukushima, and S. Kitahara: in Thermal Spray: International Advances in Coatings Technology, C.C. Berndt, ed., ASM INTERNATIONAL, Materials Park, OH, 1992, pp. 903–09.
D.J. Greving, J.R. Shadley, and E.F. Rybicki: J. Thermal Spray Technol., 1994, vol. 3, pp. 371–78.
T.W. Clyne and S.C. Gill: J. Thermal Spray Technol., 1996, vol. 5, pp. 401–18.
S. Kuroda: in Thermal Spray: Meeting the Challenges of the 21st Century, C. Coddet, ed., ASM INTERNATIONAL, Materials Park, OH, 1998, pp. 539–50.
O. Kesler, J. Matejicek, S. Sampath, S. Suresh, T. Gnaeupel-Herold, P.C. Brand, and H.J. Prask: Mater. Sci. Eng. A, 1998, vol. A257, pp. 215–24.
I. Iordanova and K.S. Forcey: Surface Coatings Technol., 1997, vol. 91, pp. 174–82.
J. Matejicek, S. Sampath, P.C. Brand, and H.J. Prask: in Thermal Spray: A United Forum for Scientific and Technological Advances, C.C. Berndt, ed., ASM INTERNATIONAL, Materials Park, OH, 1997, pp. 861–66.
J. Matejicek, S. Sampath, and J. Dubsky: J. Thermal Spray Technol., 1998, vol. 7, pp. 489–96.
S. Kuroda, Y. Tashiro, H. Yumoto, S. Taira, H. Fukanuma, and S. Tobe: J. Thermal Spray Technol., 2001, vol. 10, pp. 367–74.
R. Knight and R.W. Smith: in Thermal Spray Coatings: Research, Design, and Applications, C.C. Berndt and T.F. Bernecki, eds., ASM INTERNATIONAL, Materials Park, OH, 1993, pp. 607–12.
S.C. Gill and T.W. Clyne: Thin Solid Films, 1994, vol. 250, pp. 172–80.
W.D. Swank, R.A. Gavalya, J.K. Wright, and R.N. Wright: in Thermal Spray: Surface Engineering via Applied Research, C.C. Berndt, ed., ASM INTERNATIONAL, Materials Park, OH, 2000, pp. 363–69.
O. Kesler, M. Finot, S. Suresh, and S. Sampath: Acta Mater., 1997, vol. 45, pp. 3123–34.
D.J. Greving, E.F. Rybicki, and J.R. Shadley: J. Thermal Spray Technol., 1994, vol. 3, pp. 379–88.
J. Matejicek, S. Sampath, P.C. Brand, and H.J. Prask: Acta Mater., 1999, vol. 47, pp. 607–17.
J. Matejicek and S. Sampath: Acta Mater., 2001, vol. 49, pp. 1993–99.
E.F. Rybicki, J.R. Shadley, X. Xiong, and D.J. Greving: J. Thermal Spray Technol., 1995, vol. 4, pp. 377–84.
J.W. Adams, R. Ruh, and K.S. Mazdiyasn: J. Am. Ceram. Soc., 1997, vol. 80, pp. 903–08.
T.C. Totemeier, R.N. Wright, and W.D. Swank: Intermetallics, in press, 2004.
Y. Itoh, M. Saitoh, and M. Tamura: J. Eng. Gas Turbines and Power, 2000, vol. 122, pp. 43–49.
S. Kuroda, Y. Tashiro, H. Yumoto, S. Taira, and H. Fukanuma: in Thermal Spray: Meeting the Challenges of the 21st Century, C. Coddet, ed., ASM INTERNATIONAL, Materials Park, OH, 1998, pp. 569–74.
C.-J. Li and Y.-Y. Wang: J. Thermal Spray Technol., 2002, vol. 11, pp. 523–29.
W.D. Swank, J.R. Fincke, D.C. Haggard, and G. Irons: in Thermal Spray Industrial Applications, C.C. Berndt and S. Sampath, eds., ASM INTERNATIONAL, Materials Park, OH, 1994, pp. 307–12.
W.D. Swank, J.R. Fincke, D.C. Haggard, G. Irons, and R. Bullock: in Thermal Spray Industrial Applications, C.C. Berndt and S. Sampath, eds., ASM INTERNATIONAL, Materials Park, OH, 1994, pp. 319–24.
I.C. Noyan and J.B. Cohen: Residual Stress—Measurement by Diffraction and Interpretation, Springer-Verlag, New York, NY, 1987.
S.H. Crandall, N.C. Dahl, and T.J. Lardner: An Introduction to the Mechanics of Solids, 2nd ed., McGraw-Hill, New York, NY, 1978.
Stress User’s Manual, Bruker AXS GmbH, Karlsruhe, Germany, 1999.
T.C. Hanson, C.M. Hackett, and G.S. Settles: J. Thermal Spray Technol., 2002, vol. 11, pp. 75–85.
R.C. Dykhuizen, M.F. Smith, D.L. Gilmore, R.A. Neiser, X. Jiang, and S. Sampath: J. Thermal Spray Technol., 1999, vol. 8, pp. 559–64.
C.M. Hackett and G.S. Settles: in Thermal Spray: Practical Solutions for Engineering Problems, C.C. Berndt, ed., ASM INTERNATIONAL, Materials Park, OH, 1996, pp. 665–73.
R.N. Wright, J.R. Fincke, W.D. Swank, and D.C. Haggard: in Thermal Spray: Practical Solutions for Engineering Problems, C.C. Berndt, ed., ASM INTERNATIONAL, Materials Park, OH, 1996, pp. 511–16.
Y.C. Tsui and T.W. Clyne: Thin Solid Films, 1997, vol. 306, pp. 23–33.
J.H. Schneibel: in Processing, Properties, and Applications of Iron Aluminides, J.H. Schneibel and M.A. Crimp, eds., TMS, Warrendale, PA, 1994, pp. 329–42.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Totemeier, T.C., Wright, R.N. & Swank, W.D. Residual stresses in high-velocity oxy-fuel metallic coatings. Metall Mater Trans A 35, 1807–1814 (2004). https://doi.org/10.1007/s11661-004-0089-5
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-004-0089-5