Abstract
The influence of time and isothermal transformation temperature on the morphology of acicular ferrite in a medium-carbon microalloyed steel has been studied using optical and transmission electron microscopy (TEM). This study has been carried out with the analysis of the microstructures obtained with one- and two-stage isothermal treatments at 400 °C and 450 °C, following austenitization at 1250 °C. The heat treatments were interrupted at different times to observe the evolution of the microstructure at each temperature. The results show that a decrease in the isothermal transformation temperature gives rise to the development of sheaves of parallel ferrite plates, similar to bainitic sheaves, but intragranularly nucleated. These replace the face-to-edge nucleation that dominates the transformation at higher temperatures. The TEM observations reveal that the plates correspond to upper acicular ferrite and the sheaves to lower acicular ferrite. In this last case, cementite precipitates are present at the ferrite unit interiors and between the different platelets.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
H.K.D.H. Bhadeshia: Bainite in Steels. Transformations, Microstructure and Properties, 2nd Edition, The Institute of Materials, London, 2001, ch. 10.
Z. Zhang and R.A. Farrar: Mater. Sci. Technol., 1996, vol. 12, pp. 237–60.
S.S. Babu and H.K.D.K. Bhadeshia: Mater. Sci. Eng. A, 1992, vol. 156, pp. 1–9.
M. Strangwood and H.K.D.H. Bhadeshia: Proc. Int. Conf. Advances in Welding Science and Technology, ASM, Cleveland, OH, 1987, pp. 187–91.
D.J. Abson and R.E. Dolby: Weld. Inst. Res. Bull., 1987, vol. 19, pp. 202–07.
R.C. Cochrane and P.R. Kirkwood: in Trends in Steels and Consumables for Welding, The Welding Institute, Abingdon, 1978, pp. 103–21.
O. Grong and D.K. Matlock: Int. Met. Rev., 1986, vol. 31 (1), pp. 27–48.
R.A. Ricks, P.R. Howell, and G.S. Barritte, Jr.: Mater. Sci., 1982, vol. 17, pp. 732–40.
S. Ohkita, H. Homma, S. Tsushima, and N. Mori: Aus. Welding J., 1984, pp. 29–36.
D.J. Abson, R.E. Dolby, and P.H.M. Hart: Trends in Steels and Consumables for Welding, Conf. Proc., The Welding Institute, Abingdon, 1987, pp. 75–101.
J.G. Garland and P.R. Kirkwood: Met. Constr., 1975, vol. 7 (5), pp. 275–83.
J.G. Garland and P.R. Kirkwood: Met. Constr., 1975, vol. 7 (6), pp. 320–30.
J.M. Dowling, J.M. Corbett, and H.W. Kerr: Metall. Trans. A, 1986, vol. 17, pp. 1611–23.
O. Grong and D.K. Matlock: Int. Met. Rev., 1986, vol. 31 (1), pp. 27–44.
E.S. Kayali, J.M. Corbett, and H.W. Kerr: J. Mater. Sci. Lett., 1983, vol. 2, pp. 123–28.
S.K. Liu and D.L. Olson: Weld. Res. Suppl., 1986, vol. 65, pp. 139s-149s.
M. Imagumbai, R. Chijiiwa, N. Aikawa, M. Nagumo, H. Homma, M. Matsuda, and H. Mimura: HSLA Steels: Metallurgy and Aplications, J.M. Gray, T. Ko, Z. Shouhua, W. Baorong, and X. Xishan, eds., ASM INTERNATIONAL, Metals Park, OH, 1985, pp. 557–66.
T. Ochi, T. Takahashi, and H. Takada: Proc. 30th Mechanical Working and Steel Processing Conf., Iron and Steel Society, Warrendale, PA, 1989, vol. XXVI, pp. 65–72.
F.J. Barbaro, P. Krauklis, and K.E. Easterling: Mater. Sci. Technol., 1989, vol. 5, pp. 1057–68.
F. Ishikawa, T. Takahashi, and T. Ochi: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 929–36.
J.M. Gregg and H.K.D.H. Bhadeshia: Acta Mater., 1997, vol. 45 (2), pp. 739–48.
K. Yamamoto, T. Hasegawa, and J. Takamura: Iron Steel Inst. Jpn. Int., 1996, vol. 36, pp. 80–86.
E. Anelli, C. Andena, S. Matera, P. Harrison, I. Gutierrez, D. Porter, and T. Siwecki: ECSC Research Project Agreement 7210 PR/037 (97-D3.05a,b,c,d,e), 1998 Annual Report.
M.A. Linaza, J.L. Romero, J.M. Rodriguez-Ibabe, and J.J. Urcola: Scripta Metall. Mater., 1993, vol. 29, pp. 1217–22.
M.A. Linaza, J.L. Romero, J.M. Rodriguez-Ibabe, and J.J. Urcola: Scripta Metall. Mater., 1995, vol. 32, pp. 395–400.
I. Madariaga and I. Gutierrez: Scripta Mater., 1997, vol. 37 (8), pp. 1185–92.
I. Madariaga, J.L. Romero, and I. Gutiérrez: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1003–15.
I. Madariaga and I. Gutiérrez: Acta Mater., 1999, vol. 47 (3), pp. 951–60.
M. Díaz-Fuentes, I. Madariaga, J.M. Rodríguez-Ibabe, and I. Gutiérrez: J. Construct. Steel Res., 1998, vol. 46 (1–3), pp. 413–14.
M. Díaz-Fuentes, I. Madariaga, and I. Gutiérrez: in Microalloying in Steels, J.M. Rodriguez-Ibabe, I. Gutierrez, and B. Lopez, eds., Materials Science Forum Vols. 284–286, Trans Tech Publications Ltd., Aedermannsdorf, Switzerland, 1998, pp. 245–52.
J.L. Romero, M.A. Linaza, J.I. San Martin, J.M. Rodriguez-Ibabe, and J.J. Urcola: Rev. Met. CENIM, 1996, vol. 32, pp. 1–13.
I. Madariaga and I. Gutiérrez: in Microalloying in Steels, J.M. Rodriguez-Ibabe, I. Gutierrez, and B. Lopez, eds., Materials Science Forum Vols. 284–286, Trans Tech Publications Ltd., Aedermannsdorf, Switzerland, 1998, pp. 419–26.
I. Madariaga and I. Gutiérrez: Conf. Proc. “TRATERMAT 98,” Madrid, 1998, pp. 143–50.
B.D. Cullity: Elements of X-ray Diffraction, Addison-Wesley, Reading, MA, 1978, pp. 350–68.
C.H. Macgillavry and G.D. Rieck: International Tables for X-Ray Crystallography, The Kynoch Press, Birmingham, England, 1968, vol. 3.
G. Maeder, Y. Ramon, G. Tharel, and J. Barralis: Mem. Sci. Rev. Met., 1975, pp. 397–405.
G.B. Olson and W.S. Owen: New Aspects of Martensitic Transformation, Institute of Metals, Tokyo, Japan, 1976, pp. 105–10.
J.R. Yang and H.K.D.H. Bhadeshia: in Advances in Welding Science and Technology, S.A. David, ed., ASM, Metals Park, OH, 1986, pp. 187–91.
S.J. Matas and R.F. Hehemann: Trans. TMS-AIME, 1961, vol. 221, pp. 179–85.
H.K.D.H. Bhadeshia and J.W. Christian: Metall. Trans. A, 1990, vol. 21A, pp. 767–97.
H.K.D.H. Bhadeshia: Bainite in Steels. Transformations, Microstructure and Properties, The Institute of Materials, London, 1992, ch. 3.
A. Bagaryatskii: Dokl. Akad. Nauk SSSR, 1950, vol. 73, p. 1161.
W. Pitsch: Arch. Eisenhuettenwes., 1963, vol. 34, p. 381.
G.V. Kurdjumov and G. Sachs: Z. Phys., 1930, vol. 64, p. 325.
H.K.D.H. Bhadeshia: Worked Examples in the Geometry of Crystals, The Institute of Metals, London, 1987.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Madariaga, I., Gutierrez, I. & Bhadeshia, H.K.D.H. Acicular ferrite morphologies in a medium-carbon microalloyed steel. Metall Mater Trans A 32, 2187–2197 (2001). https://doi.org/10.1007/s11661-001-0194-7
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-001-0194-7