Abstract
The fracture toughness of alloy 600 and its weld, EN82H, was characterized in 54 °C to 338 °C air and hydrogenated water. Elastic-plastic J IC testing was performed due to the inherent high toughness of these materials. Alloy 600 exhibited excellent fracture toughness under all test conditions. While EN82H welds displayed excellent toughness in air and high-temperature water, a dramatic toughness degradation occurred in water at temperatures below 149 °C. Comparison of the cracking response in low-temperature water with that for hydrogen-precharged specimens tested in air demonstrated that the loss in toughness is due to a hydrogen-induced intergranular cracking mechanism. At loading rates above ∼1000 MPa\(\sqrt m /h\), the toughness in low-temperature water is improved because there is insufficient time for hydrogen to embrittle grain boundaries. Electron fractographic examinations were performed to correlate macroscopic properties with key microstructural features and operative fracture mechanisms.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
P. Saint Paul and G. Slama: Proc. 5th Int. Symp. on Environmental Degradation of Materials in Nuclear Power Systems—Water Reactors, ANS, La Grange Park, IL, 1992, pp. 39–49.
D. Alter, Y. Robin, M. Pichon, A. Teissier, and B. Thomeret: Proc. 5th Int. Symp. on Environmental Degradation of Materials in Nuclear Power Systems—Water Reactors, ANS, La Grange Park, IL, 1992, pp. 661–666.
D. Buisine, F. Cattant, J. Champredonde, C. Pichon, C. Benhamou, A. Gelpi, and M. Vaindirlis: Proc. 6th Int. Symp. on Environmental Degradation of Materials in Nuclear Power Systems—Water Reactors, TMS, Warrendale, PA, 1993, pp. 845–51.
C.M. Brown and W.J. Mills: Corrosion, 1999, vol. 55, pp. 173–86.
D.M. Symons, J.P. Foster, and M.G. Burke: Proc. 8th Int. Symp. on Environmental Degradation of Materials in Nuclear Power Systems—Water Reactors, ANS, La Grange Park, IL, 1997, vol. 1, pp. 237–48.
W.J. Mills: J. Testing Evaluation, 1981, vol. 9, pp. 56–62.
P.C. Paris, H. Tada, A. Zahoo, and H. Ernst: Elastic-Plastic Fracture, ASTM STP 668, ASTM, Philadelphia, PA, 1979, pp. 5–36.
J.A. Begley and J.D. Landes: Fracture Toughness, Proc. 1971 Nat. Symp. on Fracture Mechanics, Part II, ASTM STP 514, ASTM, Philadelphia, PA, 1972, pp. 1–20.
W.C. Porr and W.J. Mills: “Application of the Normalization Data Analysis Technique for Single Specimen R-Curve Determination,” Bettis Atomic Power Laboratory, West Mifflin, PA, Report No. B-T-3269, Feb. 1999.
H.C. Rogers: Ductility, ASM, Cleveland, OH, 1968, pp. 31–61.
T.B. Cox and J.R. Low, Jr.: Metall. Trans., 1974, vol. 5, pp. 1457–70.
W.J. Mills, M.R. Lebo, and J.J. Kearns: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 1579–96.
W.W. Gerberich and Y.T. Chen: Metall. Trans., 1975, vol. 6, pp. 271–78.
B.B. Baranowski, S. Majchrzak, and T.B. Flanagan: J. Phys. F: Metal Phys., 1971, vol. 1, pp. 258–61.
M.L. Wayman and G.C. Smith: J. Phys. Chem. Solids, 1971, vol. 32, p. 103.
J.R. Rice and M.A. Johnson: Inelastic Behavior of Solids, McGraw-Hill, New York, NY, 1970, pp. 641–72.
R.M. McMeeking: J. Mech. Phys. Solids, 1977, vol. 25, pp. 357–81.
D.M. Symons: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 655–63.
D.M. Symons, G.A. Young, and J.R. Scully: Metall. Mater. Trans. A, 2001, vol. 32A, pp. 369–77.
W.J. Mills: Int. Mater. Rev., 1997, vol. 42, pp. 45–82.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Mills, W.J., Brown, C.M. Fracture toughness of alloy 600 and an EN82H weld in air and water. Metall Mater Trans A 32, 1161–1174 (2001). https://doi.org/10.1007/s11661-001-0126-6
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-001-0126-6