Abstract
Mass movements are very common problems in the eastern Black Sea region of Turkey due to its climate conditions, geological, and geomorphological characteristics. High slope angle, weathering, dense rainfalls, and anthropogenic impacts are generally reported as the most important triggering factors in the region. Following the portal slope excavations in the entrance section of Cankurtaran tunnel, located in the region, where the highly weathered andesitic tuff crops out, a circular toe failure occurred. The main target of the present study is to investigate the causes and occurrence mechanism of this failure and to determine the feasible remedial measures against it using finite element method (FEM) in four stages. These stages are slope stability analyses for pre- and postexcavation cases, and remediation design assessments for slope and tunnel. The results of the FEM-SSR analyses indicated that the insufficient initial support design and weathering of the andesitic tuffs are the main factors that caused the portal failure. After installing a rock retaining wall with jet grout columns and reinforced slope benching applications, the factor of safety increased from 0.83 to 2.80. In addition to slope stability evaluation, the Rock Mass Rating (RMR), Rock Mass Quality (Q) and New Austrian Tunneling Method (NATM) systems were also utilized as empirical methods to characterize the tunnel ground and to determine the tunnel support design. The performance of the suggested empirical support design, induced stress distributions and deformations were analyzed by means of numerical modelling. Finally, it was concluded that the recommended stabilization technique was essential for the dynamic long-term stability and prevents the effects of failure. Additionally, the FEM method gives useful and reasonably reliable results in evaluating the stability of cut slopes and tunnels excavated both in continuous and discontinuous rock masses.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Abramson LW, Lee TS, Sharma S, Boyce GM (2001) Slope stability and stabilization methods, 2nd edn. Wiley, New York. p 736.
Ahmadi M, Eslami M (2011) A New Approach to plane failure of rock slope stability based on water flow velocity in discontinuities for the Latian dam reservoir landslide. Journal of Mountain Science 8(2): 124–130. DOI: 10.1007/s11629-011-2088-5
Akgun A (2011) Assessment of possible damaged areas due to landslide-induced waves at a constructed reservoir using empirical approaches: Kurtun (North Turkey) dam reservoir area. Natural Hazards and Earth System Sciences 11(5): 1341–1350. DOI: 10.5194/nhess-11-1341-2011
Akgun A, Bulut F (2007) GIS-based landslide susceptibility for Arsin-Yomra (Trabzon, North Turkey) region. Environmental Geology 51: 1377–1387. DOI: 10.1007/s00254-006-0435-6
Alemdag S, Akgun A, Kaya A, Gokceoglu C (2014) A large and rapid planar failure: causes, mechanism and consequences (Mordut, Gumushane, Turkey). Arabian Journal of Geosciences 7: 1205–1221. DOI: 10.1007/s12517-012-0821-1
Alemdag S, Kaya A, Karadag M, et al. (2015) Utilization of the limit equilibrium and finite element methods for the stability analysis of the slope debris: an example of the Kalebasi district (NE Turkey). Journal of African Earth Sciences 106: 134–146. DOI: 10.1016/j.jafrearsci.2015.03.010
ASTM (2000) Standard Test Methods for Prebored Pressuremeter Testing in Soils (Withdrawn 2016). ASTM D4719-07, West Conshohocken, PA.
ASTM (2009) Standard test methods for laboratory determination of density (unit weight) of soil specimens. ASTM D7263-09, West Conshohocken, PA.
ASTM (2011) Standard practice for classification of soils for engineering purposes (Unified Soil Classification System). ASTM D2487-11, West Conshohocken, PA.
Barton N (2002) Some new Q-value correlations to assist in site characterization and tunnel design. International Journal of Rock Mechanics and Mining Sciences 39(1): 185–216. DOI: 10.1016/S1365-1609(02)00011-4
Barton NR (1972) A model study of rock-joint deformation. International Journal of Rock Mechanics and Mining Sciences 9: 579–602.
Barton NR, Bandis SC (1990) Review of predictive capabilities of JRC-JCS model in engineering practice. In: Proceedings of the International Symposium on Rock Joints, Loen. pp 603–610.
Barton NR, Lien R, Lunde J (1974) Engineering classification of rock masses for the design of tunnel support. Rock Mechanics 4: 189–239.
Beer G (1985) An isoparametric joint/interface element for finite element analysis. International Journal for Numerical Methods in Engineering 21(4): 585–600. DOI: 10.1002/nme. 1620210402
Bieniawski ZT (1989) Engineering Rock Mass Classifications. Wiley, New York. p 251.
Bishop AW (1955) The use of the slip circle in the stability analysis of slopes. Geotechnique 5: 7–17.
Bishop AW, Morgenstern N (1960) Stability coefficients for earth slopes. Geotechnique 10(4): 129–150.
Borja-Baeza RC, Esteban-Chávez O, Marcos-López J, et al. (2006) Slope instability on pyroclastic deposits: landslide distribution and risk mapping in Zacapoaxtla, Sierra Norte De Puebla, Mexico. Journal of Mountain Science 3(1): 1–19. DOI: 10.1007/s11629-006-0001-4
Bowles JE (1988) Foundation analysis and design. McGraw-Hill Book Company, New York.
Brill GT, Burke GK, Ringen AR (2003) A ten year perspective of jetgrouting: advancements in applications and technology. Proceedings of the 3rd International Conference–Grouting and Ground Treatment, New Orleans 1(120): 218–235.
Bulut F, Boynukalin S, Tarhan F, Ataoglu E (2000) Reliability of landslide isopleth maps. Bulletin of Engineering Geology and the Environment 58: 95–98. DOI: 10.1007/s100640050002
Cai M, Kaiser PK, Tasaka Y, Minami M (2007) Determination of residual strength parameters of jointed rock masses using the GSI system. International Journal of Rock Mechanics and Mining Sciences 4(2): 247–265. DOI: 10.1016/j.ijrmms.2006. 07.005
Capkinoglu S (1981) Geology of the district between Borcka and Cavuslu (Hopa). MSc. Thesis, Karadeniz Technical University.
Deere DU (1964) Technical description of rock cores for engineering purposed. Rock Mechanics and Rock Engineering 1: 17–22.
Del Gaudio V, Trizzino R, Calcagnile G, et al (2000) Landsliding in seismic areas: the case of the Acquara-Vadoncello landslide (southern Italy). Bulletin of Engineering Geology and the Environment 59: 23–37. DOI: 10.1007/s100640000054
Du GL, Zhang YS, Iqbal J, et al. (2017) Landslide susceptibility mapping using an integrated model of information value method and logistic regression in the Bailongjiang watershed, Gansu Province, China. Journal of Mountain Science 14(2):249–268. DOI: 10.1007/s11629-016-4126-9
Fahimifar A, Abdolmaleki A, Soltani P (2013) Stabilization of rock slopes using geogrid boxes. Arabian Journal of Geoscience 7(2): 609–621. DOI: 10.1007/s12517-012-0755-7
Fell R, Walker BF, Finlay PJ (1996) Estimating the probability of landsliding. Proceedings 7th Australian New Zealand Conference on Geomechanics, Adelaide, Institution of Engineers Australia, Canberra. pp 304–311.
Fellenius W (1936) Calculation of the stability of earth dams. Proc. Transactions of the 2nd Congress on Large Dams, International Commission on Large Dams of the World Power Conference 4: 445–462.
Gardner JS, Saczuk E (2004) Systems for hazards identification in high mountain areas: An example from the Kullu District, western Himalaya. Journal of Mountain Science 1(2): 115–127. DOI: 10.1007/BF02919334
Genc S (1993) Structural and geomorphological aspects of the Catak landslide, NE Turkey. Quarterly Journal of Engineering Geology and Hydrogeology 26(2): 99–108. DOI: 10.1144/GSL.QJEG.1993.026.02.02
Ghaboussi J, Wilson EL, Isenberg J (1973) Finite element for rock joints and interfaces. Journal of the Soil Mechanics and Foundations Division, ASCE 99(M10): 833–848.
Goodman RE, Taylor RL, Brekke TL (1968) A model for the mechanics of jointed rock. Journal of the Soil Mechanics and Foundations Division, ASCE 637–659.
Griffiths DV, Lane PA (1999) Slope stability analysis by finite elements. Geotechnique 49(3): 387–403. DOI: 10.1680/geot. 1999.49.3.387
Guatteri G, Kauschinger JL, Doria AC, Perry EB (1988) Advances in the construction and design of jetgrouting methods in South America. Proceedings of the International Conference on Case Histories in Geotechnical Engineering 5(32): 1037–1046.
Guven IH (1993) 1/25000 Scale geology map of eastern Pontides. Mineral Research and Exploration Institute of Turkey (MTA) Publication.
Guzzetti F, Carrara A, Cardinali M, Reichenbach P (1999) Landslide hazard evaluation: a review of current techniques and their application in a multi-scale study, Central Italy. Geomorphology 31: 181–216. DOI: 10.1016/S0169-555X(99)00078-1
Hammah RE, Yacoub TE, Corkum B, Curran JH (2008) The practical modelling of discontinuous rock masses with finite element analysis. In Proceedings of the 42nd US Rock Mechanics Symposium and 2nd US Canada Rock Mechanics Symposium, San Francisco.
Hammah RE, Yacoub TE, Curran JH (2006) Investigating the performance of the shear strength reduction (SSR) method on the analysis of reinforced slopes. In: Proceedings of the 59th Canadian Geotechnical Conference, Vancouver.
Hart RD, Detournay C, Cundall PA (2008) Continuum and distinct element modeling in geo-engineering. In: Cundall PA (ed) Proceedings First FLAC/DEM Symposium, Minneapolis. p 698.
Hoek E, Carranza-Torres C, Corkum B (2002) Hoek-Brown failure criterion-2002 edition. Proceedings of NARMSTAC2002, Mining Innovation and Technology, Toronto, Canada. pp 267–273.
Hoek E, Carter TG, Diederichs MS (2013) Quantification of the Geological Strength Index chart. 47th US Rock Mechanics and Geomechanics Symposium, San Francisco, USA.
ISRM (2007) The complete ISRM suggested methods for rock characterization, testing and monitoring: 1974–2006. International Society of Rock Mechanics Turkish National Group, Ankara, Turkey. p 628.
Janbu N (1954) Stability analysis of slopes with dimensionless parameters. Soil Mechanics Series No. 46, Harvard University. p 81.
Ju NP, Huang J, Huang RQ, et al. (2015) A real-time monitoring and early warning system for landslide in southwest China. Journal of Mountain Science 12(5): 1219–1228. DOI: 10.1007/s11629-014-3307-7
Karaman K (2013) Evaluation of rock slope stability by different methods (Unye, Ordu). Journal of Geological Engineering 37: 27–47.
Karaman K, Ercikdi B, Kesimal A (2013) Assessment of slope stability and excavatability of rocks in a limestone quarry. Earth Sciences Research Journal 17: 169–181.
Kaya A (2012) The geotechnical investigation of the Cankurtaran (Hopa-Artvin) tunnel alignment and surrounding area. Ph.D. Thesis, Karadeniz Technical University.
Kaya A (2016) Geotechnical assessment of a slope stability problem in the Citlakkale residential area (Giresun, NE Turkey), Bulletin of Engineering Geology and the Environment. DOI: 10.1007/s10064-016-0896-0
Kaya A, Akgün A, Karaman K, Bulut F (2015) Understanding the mechanism of a slope failure on a nearby highway tunnel route by different slope stability analysis methods: a case from NE Turkey. Bulletin of Engineering Geology and the Environment 75(3): 945–958. DOI: 10.1007/s10064-015-0770-5
Kaya A, Alemdag S, Dag S, Gürocak Z (2016) Stability assessment of high-steep cut slope debris on a landslide (Gumushane, NE Turkey). Bulletin of Engineering Geology and the Environment 1(75): 89–99. DOI: 10.1007/s10064-015-0753-6
Kaya A, Bulut F (2013) Stability analyses of tunnels excavated in weak rock masses using empirical and numerical methods. Journal of Geological Engineering 37(2): 103–116.
Ketin I (1966) Tectonic units of Anatolia. Journal of General Directorate of Mineral Research and Exploration (MTA) 66: 23–34.
KGM (2013) Specification for highway works (In Turkish). Turkish General Directorate of Highways, Ankara.
Li AJ, Merifield RS, Lyamin AV (2011) Effect of rock mass disturbance on the stability of rock slopes using the Hoek-Brown failure criterion. Computers and Geotechnics 38(2011): 546–558. DOI: 10.1016/j.compgeo.2011.03.003
Li X (2007) Finite element analysis of slope stability using a nonlinear failure criterion. Computers and Geotechnics 34: 127–136. DOI: 10.1016/j.compgeo.2006.11.005
Lowe J, Karafiath L (1959) Stability of earth dams upon drawdown. Proc. 1st PanAmerican Conference on Soil Mechanics and Foundation Engineering 2: 537–552.
Lugeon M (1933) Dams and geological field investigation methods and permeabilization. Literature of Paris University, Paris. (Barrages et geologic methods de recherche terrasement et un permeabilisation. Litrairedes Universite, Paris.)
Manouchehrian A, Gholamnejad J, Sharifzadeh M (2014) Development of a model for analysis of slope stability for circular mode failure using genetic algorithm. Environmental Earth Sciences 71(3): 1267–1277. DOI: 10.1007/s12665-013-2531-8
Matsui T, Sam KC (1992) Finite element slope stability analysis by shear strength reduction technique. Soils and Foundations 32(1): 59–70.
Menard L (1956) An apparatus for measuring the strength of soils in place. Master of Science Thesis, University of Illinois
Menard L (1975) Interpretation and application of pressuremeter test results to foundation design. Sols-Soils No: 26
MGM (2016) Turkish State Meteorological Servive. http://www.mgm.gov.tr/iklim/iklim-siniflandirmalari.aspx. Accessed 23 September 2016
Mining Research Laboratories (Canada) (1977) Pit Slope Manual: Supplement 5-1, Plane Shear Analysis. Ottawa: Canada Centre for Mineral and Energy Technology, pp 16–77.
Mohr O (1900) Which conditions determine the elasticity limit and failure of a material? Journal of the Association of German Engineers (Welche umstande bedingen die elastizitatsgrenze und den bruch eines materials? Zeit des Ver Deut Ing) 44: 1524–1530.
Morgenstern NR, Price VE (1967) A numerical method for solving the equations of stability of general slip surfaces. Computer Journal 9(4): 388–393.
Ö-NORM B2203 (1994) Underground construction work contract standard, Austrian standards, Austria. (Untertagebauarbeiten werkvertragsnorm, Österreichischer Normen, Österreich).
Pelizza S, Peila D (1993) Soil and rock reinforcements in tunnelling. Tunnelling and Underground Space Technology 8(3):357–372. DOI: 10.1016/0886-7798(93)90020-V
Rocscience Inc. (2002) RocLab version 1.0 -rock mass strength analysis using the generalized Hoek-Brown failure criterion. Toronto, ON. http://www.rocscience.com
Rocscience Inc. (2004) Dips Version 5.0 -graphical and statistical analysis of orientation data. Toronto, ON. http://www.rocscience.com
Rocscience Inc. (2010) Slide version 6.0 -2D limit equilibrium slope stability analysis, Toronto, ON. http://www.rocsci ence.com
Rocscience Inc. (2011) Phase2 version 8.0–finite element analysis for excavations and slopes, Toronto, ON. http://www.rocscience.com
Sancio RT (1981) The use of back-calculations to obtain shear and tensile strength of weathered rocks. Proceedings of the International Symposium on Weak Rock, Tokyo, pp 647–652.
Sarkar S, Anbalagan R (2008) Landslide hazard zonation mapping and comparative analysis of hazard zonation maps. Journal of Mountain Science 5: 232–240. DOI: 10.1007/s11629-008-0172-2
Sarma SK (1973) Stability analysis of embankments and slopes. Geotechnique 23(3): 423–433.
Shukra R, Baker R (2003) Mesh geometry effects on slope stability calculation by FLAC strength reduction methodlinear and non-linear failure criteria. In (Brummer R, et al, eds.) proceedings of the 3rd International FLAC Symposium, Sudbury, Ontario, Canada. pp 109–116.
Spencer E (1967) A method of analysis of the stability of embankments assuming parallel inter-slice forces. Geotechnique 17(1): 11–267.
Turner KA, Schuster RL (1996) Landslides: investigation and mitigation. National Academy Press, Washington DC. p 672.
Ulusay R, Tuncay E, Sonmez H, Gokceoglu C (2004) An attenuation relationship based on Turkish strong motion data and iso-acceleration map of Turkey. Engineering Geology 74 (3-4): 265–291. DOI: 10.1016/j.enggeo.2004.04.002
USCE (1970) Engineering and design: stability of earth and rock-fill dams. Engineer Manual EM 1110-2-1902, Department of the Army, Corps of Engineers, Office of the Chief of Engineers, Washington DC.
Wang XF, Zhang DS, Zhang CG, et al. (2013) Mechanism of mining-induced slope movement for gullies overlaying shallow coal seams. Journal of Mountain Science 10(3): 388–397. DOI: 10.1007/s11629-013-2455-5
Wang XG, Wang JD, Gu TF, et al. (2017) A modified Hoek-Brown strength criterion considering the damage to reservoir bank slope rocks under water saturation-dehydration circulation. Journal of Mountain Science 14(4): 771–781. DOI: 10.1007/s11629-016-4206-x
Wyllie DC, Mah CW (2004) Rock slope engineering. Spon Press, New York.
Yang T, Yeung MC, Yang B, et al. (2016) Three-dimensional stability of landslides based on local safety factor. Journal of Mountain Science 13(9): 1515–1526. DOI: 10.1007/s11629-016-3918-2
Acknowledgments
Authors would like to express their sincerest gratitude to the editor and reviewers. Thanks are due to the Academic Writing and Translation Office of Recep Tayyip Erdogan University for improving the language of the manuscript. The author gratefully acknowledges Geological Engineer Aytuna SAYIN from the Turkish General Directorate of Highways for the office work associated with this study.
Author information
Authors and Affiliations
Corresponding author
Additional information
http://orcid.org/0000-0001-7278-333X
http://orcid.org/0000-0002-3831-4465
http://orcid.org/0000-0003-1918-0593
Rights and permissions
About this article
Cite this article
Kaya, A., Karaman, K. & Bulut, F. Geotechnical investigations and remediation design for failure of tunnel portal section: a case study in northern Turkey. J. Mt. Sci. 14, 1140–1160 (2017). https://doi.org/10.1007/s11629-016-4267-x
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11629-016-4267-x