Abstract
Vacuum-assisted spin-coating is an effective polymer filling technology for sidewall insulating of through-silicon-via (TSV). This paper investigated the flow mechanism of the vacuum-assisted polymer filling process based on experiments and numerical simulation, and studied the effect of vacuum pressure, viscosity of polymer and aspect-ratio of trench on the filling performance. A 2D axisymmetric model, consisting of polymer partially filled into the trench and void at the bottom of trench, was developed for the computational fluid dynamics (CFD) simulation. The simulation results indicate that the vacuum-assisted polymer filling process goes through four stages, including bubble formation, bubble burst, air elimination and polymer re-filling. Moreover, the simulation results suggest that the pressure significantly affects the bubble formation and the polymer re-filling procedure, and the polymer viscosity and the trench aspect-ratio influence the duration of air elimination.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Lu J Q. 3-D hyperintegration and packaging technologies for micronano systems. P IEEE, 2009, 97: 18–30
Patti R S. Three-dimensional integrated circuits and the future of system-on-chip designs. P IEEE, 2006, 94: 1214–1224
Farooq M G, Iyer S S. 3D integration review. Sci China Inf Sci, 2011, 54: 1012–1025
Koester S J, Young A M, Yu R R, et al. Wafer-level 3D integration technology. IBM J Res Dev, 2008, 52: 583–597
Sunohara M, Tokunaga T, Kurihara T, et al. Silicon interposer with TSVs (through silicon vias) and fine multilayer wiring. Electronic Components and Technology Conference(ECTC), Lake Buena Vista, Florida, 2008: 847–852
Tu K N, Tian T. Metallurgical challenges in microelectronic 3D IC packaging technology for future consumer electronic products. Sci China Tech Sci, 2013, 56: 1740–1748
Knickerbocker J U, Andry P S, Dang B, et al. Three-dimensional silicon integration. IBM J Res Dev, 2008, 52: 553–569
Topol A W, Tulipe D L, Shi L, et al. Three-dimensional integrated circuits. IBM J Res Dev, 2006, 50: 491–506
Ranganathan N, Youhe L, Lo G Q, et al. Influence of Bosch etch process on electrical isolation of TSV structures. IEEE T Compon Pack, 2011, 1: 1497–1507
Archard D, Giles K, Price A, et al. Low temperature PECVD of dielectric films for TSV applications. Electronic Components and Technology Conference (ECTC), Las Vegas, Nevada, 2010: 764–768
Beica R, Siblerud P, Sharbono C, et al. Advanced metallization for 3D integration. Electronics Packaging Technology Conference (EPTC), Singapore, 2008: 212–218
Duval F F, Okoro C, Civale Y, et al. Polymer filling of silicon trenches for 3-D through silicon vias applications. IEEE T Compon Pack, 2011, 1: 825–832
Chausse P, Bouchoucha M, Henry D, et al. Polymer filling of medium density through silicon via for 3D-packaging. Electronics Packaging Technology Conference (EPTC), Singapore, 2009: 790–794
Coudrain P, Colonna J P, Aumont C, et al. Towards efficient and reliable 300 mm 3D technology for wide I/O interconnects. Electronics Packaging Technology Conference (EPTC), Singapore, 2012: 330–335
Duval F, Tezcan D S, Swinnen B, et al. Polymer deep trench filling for Through Silicon Via technology. 13th Meeting for the Symposium on Polymers for Microelectronics, Wilmington, Delaware, 2008
Wilke M, Wippermann F, Zoschke K, et al. Prospects and limits in wafer-level-packaging of image sensors. Electronic Components and Technology Conference (ECTC), Lake Buena Vista, Florida, 2011: 1901–1907
Truzzi C, Raynal F, Mevellec V. Wet-process deposition of TSV liner and metal films. IEEE 3D System Integration Conference, San Francisco, California, 2009
Tezcan D S, Duval F, Philipsen H, et al. Scalable through silicon via with polymer deep trench isolation for 3D wafer level packaging. Electronic Components and Technology Conference (ECTC), San Diego, California, 2009
Trichur R K, Fowler M, McCutcheon J W, et al. Filling and Planarizing Deep Trenches with Polymeric Material for Through-Silicon Via Technology. 43rd International Symposium on Microelectronics, Raleigh, North Carolina, 2010: 192–196.
Kotb H E M, Isoird K, Morancho F, et al. Filling of very deep, wide trenches by Benzocyclobutene polymer. Microsyst Tech, 2009, 15: 1395–1400
Chen Q, Huang C, Wang Z. Benzocyclobutene polymer filling of high aspect-ratio annular trenches for fabrication of through-iliconias (TSVs). Microelectron Reliab, 2012, 52: 2670–2676
Chen Q, Huang C, Tan Z, et al. Low capacitance through-silicon-vias with uniform benzocyclobutene insulation layers. IEEE T Compon Pack, 2013, 3: 724–731
Batchelor G K. An Introduction to Fluid Dynamics. Cambridge Univ Press, United Kingdom, 2000
Brackbill J U, Kothe D B, Zemach C. A continuum method for modeling surface tension. J Comput Phys, 1992, 100: 335–354
http://www.dow.com/cyclotene/prod/302235.htm (Processing Procedures for CYCLOTENE 3000 Series Dry Etch Resins) last accessed: June 5, 2013
Hirt C W, Nichols B D. Volume of fluid (VOF) method for the dynamics of free boundaries. J Comput Phys, 1981, 39: 201–225
Kulkarni A A, Joshi J B. Bubble formation and bubble rise velocity in gas-liquid systems: A review. Ind Eng Chem Res, 2005, 44: 5873–5931
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Ding, Y., Yan, Y., Chen, Q. et al. Investigation on mechanism of polymer filling in high-aspect-ratio trenches for through-silicon-via (TSV) application. Sci. China Technol. Sci. 57, 1616–1625 (2014). https://doi.org/10.1007/s11431-014-5551-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11431-014-5551-z