The paper studies Ti-6Al-4V alloy specimens obtained by wire-based electron-beam additive manufacturing (EBAM) and characterized by the structure with a defective region produced by uncontrolled wire fluctuations during 3D printing. Metallographic analysis and tensile strength tests and microhardness measurements are conducted to determine the defect influence on the structure and properties of the alloy. It is shown that the defective region represents the primary β-phase grains that are finer than those of the EBAM specimens commonly exhibiting a columnar structure. The specimen microhardness both in the defective and defect-free regions, is identical. The deformation behavior of the alloy is mostly subject to the influence of such defects, since the plasticity and ultimate tensile strength of the defective region are respectively higher and lower than that of the defect-free region.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
T. D. Ngo, A. Kashani, G. Imbalzano, et al., Compos. Part B-Eng., 143, 172–196 (2018).
E. O. Olakanmi, R. F. Cochrane, and K. W. Dalgarno, Progr. Mater. Sci., 74, 401–477 (2015).
D. Herzog, V. Seyda, E. Wycisk, and C. Emmelmann, Acta Mater., 117, 371–392 (2016).
W. S.W. Harun, M. S. I. N. Kamariah, N. Muhamad, et al., Powder Technol., 327, 128–151 (2018).
B. Wysocki, P. Maj, R. Sitek, et al., Appl. Sci., 7, 657 (2017).
B. Wu, Z. Pan, D. Ding, et al., J. Mater. Process. Technol., 258, 97–105 (2018).
L. Cordova, M. Campos, and T. Tinga, JOM, 71, 1062–1072 (2019).
J. Fuchs, C. Schneider, and N. Enzinger, Weld. World, 62, 267–275 (2018).
S. Yu. Tarasov, A. V. Filippov, N. N. Shamarin, et al., J. Alloys Compd., 803, 364–370 (2019).
S.-H. Sun, Y. Koizumi, T. Saito, et al., Addit. Manuf., 23, 457–470 (2018).
E. Brandl, A. Schoberth, and C. Leyens, Mat. Sci. Eng. A-Struct., 532, 295–307 (2012).
J. Gockel, J. Beuth, and K. Taminger, Addit. Manuf., 1–4, 119–126 (2014).
A. A. Shapiro, J. P. Borgonia, Q. N. Chen, et al., J. Spacecr. Rockets, 53, 952–959 (2016).
P. Wanjara, K. Watanabe, C. Formanoir, de, et al., Adv. Mater. Sci. Eng., 2019, 3979471 (2019).
K. S. Osipovich, A. V. Chumaevskii, A. A. Eliseev, et al., Russ. Phys. J., 62, No. 8, 1486–1494 (2019).
Q. Wu, J. Lu, C. Liu, et al., Mater. Manuf. Process., 32, 1881–1886 (2017).
F. Lia, J. Z. Park, J. S. Keist, et al., Mat. Sci. Eng. A-Struct., 717, 1–10 (2018).
M. J. Bermingham, L. Nicastro, D. Kent, et al., J. Alloys Compd., 753, 247–255 (2018).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 6, pp. 57–62, June, 2020.
Rights and permissions
About this article
Cite this article
Kalashnikov, K.N., Chumaevskii, A.V., Kalashnikova, T.A. et al. Defect Formation in Titanium Alloy during Non-stationary Process of Local Metallurgy. Russ Phys J 63, 962–967 (2020). https://doi.org/10.1007/s11182-020-02124-1
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11182-020-02124-1