Abstract
Stick-slip friction is a major cause of drill-string failure. This paper addresses the problem of suppressing stick-slip induced oscillations in oil well drill strings using a control design technique known as μ-synthesis. This technique allows for the inclusion of modeling errors in the control design process in terms of uncertainty weights. The dynamic model of the drill string with stick-slip friction is highly nonlinear and has to be linearized around an operating point in order to use μ-synthesis. The difference between the linear and nonlinear models is characterized in terms of uncertainty weights and included in the control design process. The designed controllers are robust to uncertainty in the dynamic model, spillover, actuator uncertainty, and noise. Two controllers were designed using μ-synthesis and the simulation results are presented and discussed here. The first controller assumes no measurement delay; however, the second controller includes a sensor time delay in the measurements. Both controllers are robust and performed well.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Abdulgalil, F., Siguerdidjane, H.: Backstepping design for controlling rotary drilling system. In: Proceedings of 2005 IEEE Conference on Control Applications, pp. 120–124 (2005)
Abdulgalil, F., Siguerdidjane, H.: PID based on sliding mode control for rotary drilling system. In: Proceedings of EUROCON 2005 Conference, pp. 262–265 (2005)
Al-Hiddabi, S.A., Samanta, B., Seibi, A.: Nonlinear control of torsional and bending vibrations of oil well drill strings. J. Sound Vib. 265, 401–415 (2003)
Balas, G.J., Doyle, J.C., Glover, K., Packard, A., Smith, R.: μ Analysis and Synthesis Toolbox. MUSYN and the Mathworks Inc. (1995)
Brett, J.F.: The genesis of torsional drill string vibrations. In: SPE Drilling Engineering, pp. 168–174 (1992)
Canudas-de-Wit, C., Corchero, M.A., Rubio, F.R., Navarro-Lopez, E.: D-OSKIL: a new mechanism for suppressing stick-slip in oil well drill strings. In: 44th IEEE Conference on Decision and Control and 2005 European Control Conference, CDC-ECC ’05, pp. 8260–8265 (2005)
Chevallier, A.: Nonlinear stochastic drilling vibrations. PhD Thesis, Rice University, Department of Mechanical Engineering and Material Science, Houston, Texas (2000)
Christoforou, A.P., Yigit, A.S.: Fully coupled vibrations of actively controlled drilstrings. J. Sound Vib. 267, 1029–1045 (2003)
Doyle, J.C.: Analysis of feedback systems with structured uncertainties. Proc. IEEE, D 129, 242–250 (1982)
Hernandez-Suarez, R., Puebla, H., Aguilar-Lopez, R., Hernandez-Martinez, E.: An integral high-order sliding mode control approach for stick-slip. J. Petroleum Sci. Technol. 27, 788–800 (2009)
Jansen, J.D., van den Steen, L.: Active damping of self-excited torsional vibrations in oil well drill strings. J. Sound Vib. 179(4), 647–668 (1995)
Karkoub, M.A.: Robust control of a flexible slider-crank mechanism using μ-synthesis. Mechatronics J. 10(6), 649–668 (2000)
Leine, R.I., van Campen, D.H., Keultjes, W.J.G.: Stick-slip whirl interaction in drill string dynamics. J. Vib. Acoust. 124, 209–220 (2002)
Mihajlovic, N., Van Veggel, A.A., Van de Wouw, N., Nijmeijer, H.: Analysis of friction-induced limit cycling in an experimental drill-string system. ASME J. Dyn. Syst. Meas. Control 126, 709–720 (2004)
Mihajlovic, N., Van de Wouw, N., Rosielle, P.C.J.N., Nijmeijer, H.: Interaction between torsional and lateral vibrations in flexible rotor systems with discontinuous friction. Non. Dyn., author pre-print (2007)
Navarro-Lopez, E.M., Suarez, R.: Practical approach to modeling and controlling stick-slip oscillations in oil well drill strings. In: Proceedings of the 2004 IEEE International Conference on Control Applications, vol. 2, pp. 1454–1460 (2004)
Pavone, D.R., Desplans, J.P.: Application of high sampling rate downhole measurements for analysis and cure of stick-slip in drilling, SPE 28324. Paper presented at the SPE 69th Annual Technical Conference and Exhibition held in New Orleans, 25–28 September 1994
Placido, J.C.R., Santos, H.M.R., Galeano, Y.D.: Drill string vibration and wellbore instability. J. Energy Resour. Technol. 124 (2002)
Serrarens, A.F.A.: H ∞ control as applied to torsional drill-string dynamics. MSc. thesis, Eidhoven University of Technology, The Netherlands (2002)
Smit, A.T.: Using of optimal control techniques to dampen torsional drill strings vibrations. PhD thesis, University of Twente (1999)
Spanos, P.D., Chevallier, A.M., Politis, N.P., Payne, M.L.: Oil and gas well drilling: a vibrations perspective. The Shock Vib. Dig. 35, 85–103 (2003)
Tucker, R.W., Wang, C.: On the effective control of torsional vibrations in drilling systems. J. Sound Vib. 224(1), 101–122 (1999)
Van den Steen, L.: Suppressing stick-slip-induced drill string oscillations: a hyperstability approach. Ph.D. Thesis, University of Twente, Faculty of Electrical Enginiering and Applied Physics (1997)
Vinnecombe, G.: Measuring robustness of feedback systems. PhD dissertation, Department of Engineering, Cambridge (1993)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Karkoub, M., Zribi, M., Elchaar, L. et al. Robust μ-synthesis controllers for suppressing stick-slip induced vibrations in oil well drill strings. Multibody Syst Dyn 23, 191–207 (2010). https://doi.org/10.1007/s11044-009-9179-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11044-009-9179-x