Abstract
In order to identify radon-prone areas and evaluate radon risk level, a soil gas radon survey combined with gamma-ray spectrometry measurements was carried out in Shenzhen City, south China. Meanwhile, the statistical analysis was applied to evaluate the distribution of measured results. This paper presents the methodology of the radon risk assessment. A radon risk map was accomplished based on a combination of soil gas radon concentration (RC), soil air permeability (Perm.) and uranium (238U) concentration. The results showed that the distribution of soil gas RC and radon-prone areas were closely related to geologic distribution of uranium (238U) and local lithology.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Radon (222Rn half-time t 1/2 ≈ 3.82 days), a naturally occurring noble gas, is radioactive, colorless and odorless. It mainly originates from the 238U natural decay chain of rocks and soils in the earth’s crust. According to epidemiological studies, the existence of radioactive gaseous radon is considered to be the second leading cause of lung cancer after only smoking [1]. United Nations Scientific Committee on the Effects of Atomic Radiation released that 222Rn and its decay products accounts for 50 % of the total amount of individual background radiation dose (1.15 mSv/year per capita) [2].
There does not exist a consensus definition on a radon-prone area. Generically, ICRP defined it as an area where the radon concentration (RC) in building is likely to be higher than the national average. The objective of radon-prone area evaluations is to reduce public exposure to radon. Firstly, direct measurements of indoor radon are widely used to delineate radon-prone areas [3, 4]. Meanwhile, statistical analysis is often adopted to explore influential factors of indoor radon levels [5–11]. Secondly, gamma dose assessments based on the correlation of soil gas radon levels with 238U or 226Ra concentrations in soils and rocks have been adopted [12, 13]. Airborne gamma-ray spectrometry combined with geological information was also used to delineate radon-prone areas [14–17].
Soil gas radon, which is the predominant source of indoor radon, was regarded as a good predictor of radon potential (RP) [18–20]. Moreover, soil gas permeability (Perm.) is closely related to the migration of radon gas. Previous studies have revealed that the room-entry rate of radon increases with the rise of soil gas Perm. [3], which makes soil gas Perm. a primary criterion in radon mapping [20, 21]. RP mapping based on the measurements of soil gas radon and Perm. at a depth of 1 m beneath the ground has been accomplished in Czech Republic and Germany [22–25].
In China, although some regional surveys have attempted to delineate radon-prone areas [26], there is a lack of an accepted method of radon risk mapping. In 2013 the Radiation and Environment Laboratory at China University of Geosciences (Beijing) conducted a large scale radon survey in Shenzhen City, an area in southern China with a high radiation background. The main aim of this study is to present a detailed radon risk map based on soil gas radon, soil gas Perm. and uranium (238U) concentrations. A further objective is to evaluate the radon risk variation in different geological units with a spatial analysis. The accomplishment of a RP map in the study area will facilitate the radon risk assessment for human health and risk reduction.
Materials and methods
Study area
Shenzhen City is located on the south coast of Guangdong province, eastern Pearl River Delta Areas. It covers a total area of approximately 1953 km2. Shenzhen City is situated on the intersection of the west part of the north-east Lotus Hill fault and the middle part of the east–west Gaoyao–Huilai structural belt. This city is characterized by widely distributed deep faults, which would facilitate radon underground migration resulting in the increase of soil radon levels. Previous research has indicated that the average soil gas RC of Shenzhen City was 50.50 kBq/m3. The main lithology includes the Early-Cretaceous and the Late-Cretaceous biotite granite, Sinian metamorphic rocks, Devonian quartz sandstone and Jurassic quartz sandstone. In addition, Shenzhen City is located in the southern subtropical region with an average annual temperature of 23.0 °C and an average relative humidity of 74 %.
Field measurements
The soil gas RCs were measured by an RAD7 electronic radon detector (Durridge Co., Inc.). RAD7 mainly consists of a solid-state ion-implanted silicon semiconductor alpha detector and a 0.7 L hemispherical cavity with 2200 V potential relative to detector. The equipment was precisely calibrated at Durridge’s radon calibration facility [27], using radium (226Ra) source to provide controlled radon gas for calibration. According to the RAD7 user manual [28], the calibration uncertainty was 2 % (1-σ) based on counting statistics in the radon reference concentration (1.31 kBq/m3), and not including the uncertainty of the reference source which was evaluated to be within ±5 % (1-σ). In field measurements, a soil probe (a steel pipe with 8 mm inner diameter, 15 mm outer diameter and 110 cm length) was inserted down to a depth of 80 cm. The inlet port of RAD7 was connected to the sampling tube outlet using vinyl flexible tubes through a dust filter and a inlet filter (pore size 1 µm) which prevented dust particles and radon progeny from entering the chamber (Fig. 1). A small drying tube (CaSO4) was used to make sure the gas relative humidity was decreased to less than 10 %. Gas from soil interstices was pumped inside the RAD7 measuring chamber, where 222Rn was detected through α-decay of its daughter 218Po therein produced. The flow rate of pump was 1 L/min. The instrument was operated in “Sniff” mode with 3-min cycle and a single measurement at each sampling site took at least 30 min [29]. The final result was the average of stable readings in latter cycles. The equipment “Test Purge” is a necessary step before it moved to another measuring point. This survey covered an area of about 1900 km2 with 69 sampling sites distributed in different geological characteristics (Fig. 2). The geographic coordinates for all measurement sites were determined by a portable GPS.
Direct in situ soil gas Perm. measurements were performed before the soil gas radon measurements with Radon-Jok equipment using the same soil probe. The equipment works with air withdrawal by means of negative pressure. By using the facility, soil gas filled the packing element through the pressure difference, making the compressed packing element expand slowly. The less time the filling process took, the larger the soil gas Perm. was. The calculation of the gas Perm. was based on Darcy’s equation according to the equipment manual [30, 31].
Uranium (238U) concentration was measured using a portable gamma-ray spectrometer with a NaI(Tl) (Ø75 mm × 75 mm) scintillation detector (1024 channels). The energy resolution of spectrometer was 7.43 % at 662 keV. The spectrometer detector was well calibrated at China Radiometric Exploration Methodology Station of Nuclear Industry [32]. Five calibration pads were used to determine stripping ratios recommended by IAEA [33] for calculating 238U, 232Th and 40K activity concentrations in soils and rocks. The characteristic gamma-ray energy peaks are 1.46 MeV for 40K, 1.76 MeV for 214Bi and 2.26 MeV for 208Tl, respectively. Taking these three characteristic energy peaks as the positions of central peak, an inverse matrix solution spectral method was applied to acquire the conversion factors of this equipment by calculating the peak count rates of each energy range:
where I 1, I 2, and I 3 are the counting rates of three energy spectrum channels (40K, 214Bi, and 208Tl) after deduction of background rates, in cps, a 11, a 12, a 13,…,a 33 are the conversion factors, C K, C U and C Th are the mass concentrations of 40K, 238U and 232Th, in percent for 40K and mg/kg for 238U and 232Th. In field measurements, the portable spectrometer was placed on the leveling and uniform ground surface, which corresponded to the calibration condition. There were no high-large buildings interfering with the measurements. Counting time is 600 s at each measuring site. The measurement procedures were in accordance with Technique Regulation of Gamma-Ray Spectrometry on the Ground issued by The Ministry of Land and Resources of China [34]. The equivalent concentrations of 238U and 232Th and the concentration of 40K can be acquired after getting the conversion factors of spectrometer [Eq. (1)] and calculating the peak count rates of 214Bi, 208Tl and 40K.
Radon Index (RI) classification
In order to assess the radon risk of the study area, it is necessary to set up radon risk indexes. Previous research indicated a positive correlation between indoor RC and the local RI [35]. A conventional approach to quantify the RP is called the ‘Naznal RP’ [25], taking into consideration the soil gas RC and soil gas Perm. The second method to define the RP is the RI based on multivariate cross-tabulation [36]. The resulting RI is a categorical-ordinal quantity such as low, medium and high. In this study, the RI was defined based on the classification of soil gas radon, soil gas Perm. and 238U concentrations. Each of the three parameters was subdivided into three classes and scores were assigned to the input quantities. To be specific, soil gas radon concentration (RC for short) was classified to be 1, 2 or 3. If RC ≤30 kBq/m3, then grade is 1, if 30 < RC < 100 kBq/m3, then grade is 2, if RC ≥100 kBq/m3, then grade is 3 [22]. Soil gas permeability (Perm. for short) and 238U concentrations were also divided into three grades, respectively [13, 37] (Table 1). Finally, the result of RI for each measurement site was the sum of these three grades. The radon risk was determined following the order of high (RI = 8, 9), medium (RI = 6, 7) and low (RI = 3, 4, 5) categorization.
Results and discussion
Summary statistics and regression analysis
The summary statistics of soil gas RCs, soil gas Perm. and 238U concentrations of all measurement sites are shown in Table 2. The results showed that soil gas RC had a minimum of 14.63 kBq/m3, a maximum of 369.72 kBq/m3, a median of 58.47 kBq/m3 and an arithmetic average of 85.81 kBq/m3 with a standard deviation of 70.94 kBq/m3.
The measurement sites in Shenzhen City were mainly distributed in four lithological units including granite, quaternary, sandstone and backfill. The Kruskal–Wallis test showed that there was a statistically significant difference in the soil gas RCs (χ 2 = 30.81, p = 0.000 < 0.05) and 238U concentrations (χ 2 = 29.39, p = 0.000 < 0.05) among different lithological units (Table 3).
Medians of soil gas RC and soil gas Perm. (logarithmic scale) from four main lithological units were conducted a simple bivariate regression analysis, which showed a weak significant linear relationship (R 2 = 0.345) even if the outlier (the values in granite areas) was not considered (Fig. 3). However, the relationship between the soil gas RCs and 238U concentrations revealed a high positive linear correlation (R 2 = 0.715; Fig. 3), which could also be proved by the Pearson’s correlation analysis that included all measurement sites (r = 0.709, p = 0.000 < 0.05) [38].
Radon risk assessment within study area
As an overall result, soil gas RCs were higher in the western and southern parts of Shenzhen City (Fig. 2), especially in the Midwest areas. The regionalization of the radon risk map in Shenzhen City was realized by means of a grid-based and distance-weighted interpolation procedure using Software ArcGis10.2 (Fig. 4). Each grid element represented an area of 4 km × 4 km. For each raster element without measuring site, the three nearest measurement points in the same geological unit were allocated [39].
This study provided a general distribution of the radon risk on a large scale. High radon risk areas were widely distributed in the western part of Shenzhen City. Additionally, the radon risk evaluation based on the administrative areas showed that the central part of the Bao’an District, the northwest part of the Nanshan and Futian Districts were radon-prone areas in the study area. The distribution characteristics of the RP in Shenzhen City were closely related to the local lithology. The highest radon risk areas concentrated in the mid-western areas, where Yenshanian granite was widely distributed.
Conclusions
Soil gas radon distribution and radon risk assessment could be observed intuitively through the RP map of Shenzhen City. The research showed that:
-
(1)
The arithmetic average of soil gas RC in Shenzhen City was 85.81 kBq/m3, which was 12 times higher than that of the other 144 cities in China (7.3 kBq/m3).
-
(2)
Statistical analysis indicated that there were significant differences in the concentrations of soil gas radon and uranium (238U) among the different lithological units. There was a close correlation between radon-prone areas and geologic distribution of uranium (238U).
-
(3)
This survey demonstrated that the Nanshan District and the Bao’an District, which were covered with a large range of Yanshanian period granite rocks, were typical high radon risk areas.
The application of this methodology and the study of radon mapping in China is currently in progress. Further radon surveys may be extrapolated to a bigger range in China.
References
Darby S, Hill D, Auvinen A, Barros-Dios JM, Baysson H, Bochicchio F, Doll R (2005) Radon in homes and risk of lung cancer: collaborative analysis of individual data from 13 European case–control studies. Br Med J 330:223–227
UNSCEAR (United Nations Scientific Committee on the Effects of Atomic Radiation) (2008) Sources and effects of ionizing radiation. Report to General Assembly. United Nations, New York
Andersen CE (2001) Numerical modelling of radon-222 entry into houses: an outline of techniques and results. Sci Total Environ 272(1):33–42
Miles J (1998) Development of maps of radon-prone areas using radon measurements in houses. J Hazard Mater 61(1):53–58
Epstein L, Koch J, Riemer T, Orion I, Haquin G (2014) Radon concentrations in different types of dwellings in Israel. Radiat Prot Dosim. doi:10.1093/rpd/ncu346
Andersen CE, Ulbak K, Damkjær A, Kirkegaard P, Gravesen P (2001) Mapping indoor radon-222 in Denmark: design and test of the statistical model used in the second nationwide survey. Sci Total Environ 27(2):31–41
Cinti D, Poncia PP, Procesi M, Galli G, Quattrocchi F (2013) Geostatistical techniques application to dissolved radon hazard mapping: an example from the western sector of the Sabatini Volcanic District and the Tolfa Mountains (central Italy). Appl Geochem 35:312–324
Dubois G, Bossew P, Friedmann H (2007) A geostatistical autopsy of the Austrian indoor radon survey (1992–2002). Sci Total Environ. doi:10.1016/j.scitotenv.2007.02.012
Friedmann H, Gröller J (2010) An approach to improve the Austrian radon potential map by Bayesian statistics. J Environ Radioact. doi:10.1016/j.jenvrad.2009.11.008
Zhu HC, Charlet JM, Poffijn A (2001) Radon risk mapping in southern Belgium: an application of geostatistical and GIS techniques. Sci Total Environ 272(1):203–210
Appleton JD, Miles JCH (2010) A statistical evaluation of the geogenic controls on indoor radon concentrations and radon risk. J Environ Radioact 101(10):799–803
García-Talavera M, García-Pérez A, Rey C, Ramos L (2013) Mapping radon-prone areas using γ-radiation dose rate and geological information. J Radiol Prot. doi:10.1088/0952-4746/33/3/605
Ielsch G, Cushing ME, Combes P, Cuney M (2010) Mapping of the geogenic radon potential in France to improve radon risk management: methodology and first application to region Bourgogne. J Environ Radioact. doi:10.1016/j.jenvrad.2010.04.006
Appleton JD, Miles JCH, Young M (2011) Comparison of Northern Ireland radon maps based on indoor radon measurements and geology with maps derived by predictive modelling of airborne radiometric and ground permeability data. Sci Total Environ. doi:10.1016/j.scitotenv.2011.01.023
Ford KL, Savard M, Dessau JC, Pellerin E, Charbonneau BW, Shives BK (2001) The role of gamma-ray spectrometry in radon risk evaluation: a case history from Oka, Quebec. Geosci Can 28(2):59–64
Mik J, Barnet I (2002) Geological support to the National Radon Programme (Czech Republic). Bull Czech Geol Surv 77(1):13–22
Smethurst MA, Strand T, Sundal AV, Rudjord AL (2008) Large-scale radon hazard evaluation in the Oslofjord region of Norway utilizing indoor radon concentrations, airborne gamma ray spectrometry and geological mapping. Sci Total Environ. doi:10.1016/j.scitotenv.2008.09.024
Nazaroff WW, Nerojr AV (1988) Radon and its decay products in indoor air. Wiley, New York
Kardos R, Gregoric A, Jonas J, Vaupotic J, Kovacs T, Ishimori Y (2015) Dependence of radon emanation of soil on lithology. J Radioanal Nucl Chem 304:1321–1327
Mouse DG, Mushrush GW, Chrosniak CE (1992) Soil radon, permeability, and indoor radon prediction. Environ Geol Water Sci 19(2):91–96
Neznal M, Neznal M (2005) Permeability as an important parameter for radon risk classification of foundation soils. Ann Geophys Italy 48(1):175–180
Kemski J, Siehl A, Stegemann R, Valdivia-Manchego M (2001) Mapping the geogenic radon potential in Germany. Sci Total Environ 272(1):217–230
Barnet I, Miksova J, Prochazka J (1998) Radon database and radon risk map 1:500000 of the Czech Republic. Radon investigations in Czech Republic VII. Czech Geological Survey, Prague
Barnet I, Pacherová P, Neznal M (2008) Radon in geological environment—Czech experience. No. 19. Czech Geological Survey, Prague
Neznal M, Neznal M, Matolin M, Barnet I, Miksova J (2004) The new method for assessing the radon risk of building sites. Czech Geological Survey Special Paper, Prague
Wang NP, Xiao L, Li CP, Liu SM, Huang Y, Liu DL, Peng ML (2011) Distribution and characteristics of radon gas in soil from a high-background-radiation city in China. J Nucl Sci Technol 48(5):751–758
Xu BC, Buunett WC, Lane-Smith D, Yu ZG (2010) A simple laboratory-base radon calibration system. J Radioanal Nucl Chem. doi:10.1007/s10967-009-0427-6
RAD7 user manual. Durridge Company, Inc. http://www.durridge.com/documentation/RAD7%20Manual.pdf. Accessed 16 Dec 2015
Cinelli G, Tositti L, Capaccioni B, Brattich E, Mostacci D (2014) Soil gas radon assessment and development of a radon risk map in Bolsena, Central Italy. Environ Geochem Health. doi:10.1007/s10653-014-9649-9
Koorevaar P, Menelik G, Dirksen C (1983) Elements of soil physics. Elsevier, Amsterdam
Damkjaer A, Korsbech U (1992) A small-diameter probe for in situ measurements of gas permeability of soils. Radiat Prot Dosim 45:85–89
Li BC, Wang NP, Wan JH, Xiong SQ, Liu HT, Li SJ, Zhao R (2016) In-situ gamma-ray survey of rare-earth tailings dams—a case study in Baotou and Bayan Obo Districts, China. J Environ Radioact. doi:10.1016/j.jenvrad.2015.10.027
IAEA (1989) Construction and use of calibration facilities for radiometric field equipment. Technical Report No. 309. IAEA, Vienna
Wang NP, Xiao L, Li CP, Huang Y, Pei SY, Liu SM, Xie F, Cheng YX (2005) Determination of radioactivity level of 238U, 232Th and 40K in surface medium in Zhuhai City by in situ gamma-ray spectrometry. J Nucl Sci Technol 42(10):888–896
Barnet I, Pacherová P, Preusse W, Stec B (2010) Cross-border radon index map 1:100 000 Lausitz–Jizera–Karkonosze-region (northern part of the Bohemian Massif). J Environ Radioact. doi:10.1016/j.jenvrad.2009.11.009
Gruber V, Bossew P, De Cort M, Tollefsen T (2013) The European map of the geogenic radon potential. J Radiol Prot. doi:10.1088/0952-4746/33/1/51
Nazaroff WW (1982) Radon transport from soil to air. Rev Geophys 30(2):137–160
Garba N, Ramli A, Saleh M, Sanusi M, Gabdo H (2014) Assessment of terrestrial gamma radiation dose rate (TGRD) of Kelantan State, Malaysia: relationship between the geological formation and soil type to radiation dose rate. J Radioanal Nucl Chem. doi:10.1007/s10967-014-3209-8
Kemski J, Klingel R, Siehl A, Valdivia-Manchego M (2009) From radon hazard to risk prediction-based on geological maps, soil gas and indoor measurements in Germany. Environ Geol. doi:10.1007/s00254-008-1226-z
Acknowledgments
This work was financially supported by the National Natural Science Foundation of China (Nos. 41274133 and 41474107).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Liu, H., Wang, N., Chu, X. et al. Mapping radon hazard areas using 238U measurements and geological units: a study in a high background radiation city of China. J Radioanal Nucl Chem 309, 1209–1215 (2016). https://doi.org/10.1007/s10967-016-4717-5
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10967-016-4717-5