Abstract
Elemental composition of airborne dust samples retained by internal filters of air condition units (ACUs) was determined at 12 locations of Doha city, state of Qatar. Twenty-four elements: Al, Ca, Mg, Fe, Na, K, Ti, Zn, P, Sr, Mn, Ba, Cu, Cr, Ni, Pb, V, Mo, Li, Co, Sb, As, Cd, Be, were analysed by ICP-OES technique after acid digestion of the samples. The analysed components reflect 20.6% of the total sample mass. Similar or lower concentration values have been found for As, Cd, Cr, Cu, Mn, Ni, Pb, V, Zn, Al, and Fe compared to the international context of upper crust concentrations, NIST SRM (urban dust), published local dust information of outdoor, and surface terrestrial deposit (STD) counted for 7.2, 0.7, 91.8, 192.8, 369.7, 68.6, 65.3, 52.1, 824.3, 19,791, 20,508 mg/kg, respectively. The coefficient of correlation (p ≤ 0.05) showed significant association of ACUs dust elemental compositions with the main components of the local earth crust and surface deposits, ranging from the lowest 0.77 (Mg–Fe) to the highest 0.98 (Al–Fe), while Ni and V, typical anthropogenic pollutants, are also strongly correlated (0.86). These strong correlation relationships can be interpreted as the contribution of outdoor particulate to the indoor dust. Dendrogram of metal/Al ratios, based on Euclidean distance calculation and average linkage clustering method, distinguished three typical groups. Studying the enrichment factors of the three groups indicated elevated levels of Zn (131), Pb (49), Cu (32), Cd (8) and Ni (5) found indoors compared to the background composition of STD especially at locations in the industrial zone. The major elemental composition of the samples reflects the typical mineral composition of the local dust, while the trace composition demonstrates the influence of indoor sources. The collected ACU filter dust samples show significant contribution of outdoor mineral particles, non-exhaust traffic emission, industrial sources, as well as the influence of indoor activity such as smoking.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
The focus on heavy metal pollution in household dust has increased recently, as metallic elements can have a significant effect on human health and the ecosystem. Heavy metals can be toxic, persistent, bioaccumulative, and have the ability for biomagnification (Shi et al. 2011). These elements adsorbed by dust particles can easily be inhaled, ingested or absorbed via dermal contact (Glorennec et al. 2012; Sah et al. 2018; Sharma et al. 2018). Their accumulation within the tissue and internal organs (Zheng et al. 2010) can affect the central nervous system and may lead to the promotion of other diseases (Faiz et al. 2009). For instance, Li et al. (2001) demonstrated that low level lead (Pb) exposure can be detrimental to enzymic systems, as well as brain and blood production within the human body, whereas long-term exposure may affect mental development in children (Li et al. 2001; Sezgin et al. 2004) .
In hot, arid environments people tend to spend most of the time indoors (either at the workplace or at home) (Habil et al. 2016). Thus, the quality of the indoor air can have a direct impact on their health. The quality of air in Qatar, particularly in its major urban centres, has been declining for the last decades due to country’s ever-increasing industries, constructions, and vehicle numbers (Ferwati et al. 2017; Saraga et al. 2017). Elevated indoor heavy metals concentrations can be attributed to outdoor sources such as heavily traffic roads (Cao et al. 2018; Li et al. 2001) and proximity to industrial sites (Parveen et al. 2018). Moreover, natural sources of air pollution are also crucial in the country based on its desert climate, where dust storms can significantly affect air quality. A recent report released in 2013 by the Qatar Ministry of Development, Planning and Statistics (MDPS) highlighted that the pollution levels in Qatar frequently exceed the WHO recommendations as well as Qatar’s air quality targets (MDPS 2014).
Air condition units (ACUs) are used extensively in residential and commercial buildings almost all the year round in Qatar. The analysis of the dust, accumulated on their filters, can provide valuable information about the indoor air quality. Thus, researching the heavy metal content of indoor dust becomes essential and will help to understand possible changes of urban environmental quality, caused by intensive anthropogenic activities (Han and Lu 2017) in the Gulf region.
In this research, we aim to evaluate the metal content of retained dust particles and their influence on indoor air quality in Doha. Dust samples were collected from ACUs filters, and the elemental composition of the particulate matter (PM) was determined by ICP-OES analysis. Dust samples were collected at different key locations within the city, representing traffic influenced and background locations as well as industrial sites.
Materials and methods
Sample collection
Indoor house dust samples (n = 12) accumulated on air condition filters were collected from residential and commercial buildings, representing different environmental conditions, within Doha (Fig. 1). Each sampling location was carefully selected to reflect differences in the influences of local traffic, construction and industrial activity, or rural residency along the eastern coast of Doha, where most of the country’s population reside. Geographical coordinates and description of the sampling sites are given in Table 1.
The sampling period was predefined to obtain maximum loadings of the PM during the dry summer season of 2015. The ACUs filter samples were exposed for 2–3 months before sampling. Operation of the ACUs creates a low-pressure area, similar to a vacuum, attracting particles from the entire room and forming a homogenised dust that can represent the actual contamination level (Tan et al. 2007). The deposited particles were extracted from the filter tissues by gently shaking, and the falling out particles were collected on a polycarbonate sheet. The dust samples were transferred into acid-rinsed glass jars and kept at low temperature (− 4.0 °C) before digestion and analysis.
Sample preparation
Collected samples were dried in an air oven set to 105 °C for 12 h. The dried samples were then homogenised and stored in an airtight desiccator till digestion.
0.25 g of each sample was carefully weighed into a Teflon tube, and 9 ml of SuporaPure® nitric acid (6 M) was added to each tube. The tubes were placed into a HotBloc® digestion block set to 95 °C; the set temperature was maintained for 30 min after which 3 ml of SupraPure® hydrofluoric acid (16 M) was added to each vessel. After a further 30 min at 95 °C, the temperature was ramped to 135 °C and held for 60 min after which another temperature increase was applied (150 °C) until the sample dehydrated.
A 3 ml aliquot of nitric acid was added to each dry sample and diluted with 40 ml of double deionised water (DDW). The solution was allowed to boil until it was clear. The sample was then allowed to cool and further diluted to 100 ml using DDW. The samples were then filtered through a 0.22 µM syringe filter before injection and analysis via ICP/OES.
Quality assurance
A certified marine sediment reference material (CRM) PACS3 for trace metals and other constituents, originated from National Research Council Canada (NRCC), was used for the elemental analysis. Quality Control was conducted using reagent blanks, duplicate samples, spiked samples, and PACS-3 CRM at every ten samples. These CRMs were verified within 5% of their expected values for all elements. Table 2 shows the recovery detected (96–99%) for some selected heavy metals.
In almost all cases, the average measured values were within the 95% confidence limits of the certified values, and thus the accuracy determined from this approach was comparable to or better than the precision. Procedural blanks were prepared using the same analytical procedure and reagents, but without adding a sample in the digestion vials. All samples analyses were carried out triplicate and analysed in ESC ISO 17,025 accredited laboratories. The limit of detection was defined as three times of the standard deviation of the blank readings.
Environmental indexing
The enrichment factor (EF) is one of the most common environmental indices applied to distinguish the anthropogenic and natural sources of the elements in the sample based on their ratio to the primary component in the background soil composition. It is used on a broad field of environmental studies such as sediment and water sciences, and air quality research as an indicator of pollution (Gomes and Gillette 1993; Sutherland 2000; Adamo et al. 2005; Abrahim and Parker 2008; Rushdi et al. 2013; Shelley et al. 2014).
In this work, we calculated the EF for metals (Me) using aluminium as a reference due to its terrestrial origin and dominance in the earth’s crust composition within Qatar (Yigiterhan et al. 2018).
where \(\left( {\frac{{{\text{Me}}}}{{{\text{Al}}}}} \right)_{{{\text{ACU}}\,{\text{dust}}}}\) is the concentration ratio of Me and Al in the AC dust sample, and \(\left( {\frac{{{\text{Me}}}}{{{\text{Al}}}}} \right)_{\text{bcgk}}\) is their concentration ratio in the background soil.
EF value higher than 10 (EF >10) indicates the anthropogenic origin of the element, while EF<10 is attributed to natural composition (Biegalski et al. 1998; Nazir et al. 2011). The detailed classification of EF was given in Shaari et al. (2015).
Results and discussion
Elemental composition of the indoor dust
The chemical analysis of ACUs filter dust samples was conducted for 24 elements by ICP-OES technique; the detailed results of the analysis are summarised in “Appendix 1” section. The average elemental compositions of the samples are presented in Table 3. The compositions of indoor dust were compared to upper continental crustal concentrations (UCC) given by Rudnick and Gao (2003), and other local dust samples such as outdoor dust (OD), road dust (Rd) and terrestrial surface deposit (STD) collected at urban and background locations of Qatar (Yigiterhan et al. 2018) in order to determine the enrichment relative to the background composition. For a wider reference, mass concentrations of the same concerned elements in the 1648a standard reference material (SRM, urban dust) by the National Institute of Standards and Technology (NIST) are also included. The last row of the table shows the average total mass percentages of the analysed elements.
It is noted from the table that the analysed elements refer about 23.3–24.6% of the total mass of OD, Rd and STD samples, while 20.6% of the ACUs samples. The missing mass of the samples can be attributed to the unidentified major components of the minerals such as carbon and oxygen, as well as silica that could not be measured due to the analytical circumstances. Also, the organic components of the samples (Mahfouz et al. 2018) could have a significant contribution in the total sample mass. Supposing that the mineral composition of the ACUs filter is similar to the outdoor samples, the lower total mass percentage could refer to higher organic content due to especially indoor sources. The analytical results demonstrate the particular nature of the local airborne dust compared to typical urban air pollution, which reflected by the urban dust SRM. The local dust contains Ca and Mg at higher, while Al and Fe at lower concentrations than the SRM. Also, the traffic emission-related elements (Cu, Zn, Pb) are more enriched in the SRM. The total mass of the analysed elements is 16.5% in the SRM due to its different mineralogical composition (more silicate less calcite) and the higher percentage of organic compounds.
Eleven common elements were found in different publications about ACUs filter samples from the wider region of Asia, which are compared with Qatari indoor dust, presented in Table 4 (Abbasi and Tufail 2013; Al-hemoud et al. 2017; Huang et al. 2014; Siddique 2011). Our findings were within the range of the published values, except Al (1.9%), Fe (2.0%), V (52.1 ppm) and As (7.2 ppm) which were lower than literature average. In this study, average Zn concentration was found at 824 ppm, which is almost equal to the highest literature value given by Tufail et al. (2013). High Zn concentration can be attributed to outdoor anthropogenic activities such as industrial emissions and non-exhaust traffic emissions like tire debris, brake pads and road surface wear (Grigoratos and Martini 2015), but also indoor sources (Tunno et al. 2016). Similar to Zn, significant enrichment of Cu, Mo and Ni is more associated with traffic-related dust rather than local origin or transported dust (Thorpe and Harrison 2008).
In order to compare the elemental distributions between different locations, Pearson correlation coefficients were calculated at 10 locations. The two samples from the industrial zone (S13 and S14) were kept out from the correlation analysis due to their outlying high concentration values that would bias the correlation. The correlation coefficients are presented in Table 5 at a significance level of p ≤ 0.05 and showed strong correlation between 8 elements (Al, Mg, Fe, Mn, Ni, V, Li and Be) with correlation coefficients ranging from the lowest 0.77 (Mg–Fe) to the highest 0.98 (Al–Fe). Moreover, Mg and V are strongly correlated with Ba (0.84 and 0.81), V–Ni (0.86), while Mn and Li with As (0.81 and 0.71). Al, Mg, Fe, Mn are the main components of the local earth crust and surface deposits (Yigiterhan et al. 2018), while Ni and V are typical anthropogenic pollutants originated from oil combustion (Visschedijk et al. 2012). The strong correlation of these elements can be interpreted as the contribution of outdoor dust for the indoor dust samples.
Calcium, the major component of the local earth crust, shows a strong correlation with Sr (0.95), Ba (0.74), Cr (0.83) and weak correlation with Mg (0.52) and Ti (0.52). The other elements are not correlated with Ca that suggests that these elements are associated with silicates (Al2SiO5) rather than the calcium carbonate (CaCO3) fraction. On the other hand, Ca is a major element of construction materials (cement, lime, gypsum) and extensively can be found everywhere in the built environment. Since the indoor dust is a mixture of the internally generated particles and those intruded from outside, the actual indoor level of Ca depends on the relative contribution of indoor and outdoor sources that can have a high variation among the locations.
Noted however, no correlation was found for Na, Cu (except with Pb), Mo, Sb and Cd with any elements that indicate that there might be individual (indoor or outdoor) sources for these elements.
Comparison of indoor dust composition with other local samples
As the correlation analysis of the elements indicated in the previous section, the compositions of the retained indoor dust samples are determined by different—indoor and outdoor—sources. The relative concentrations of the elements can refer to their origin. Metal-to-aluminium ratio (Me/Al) is a widely applied indicator for enrichments or depletions of elements relative to the background composition (Yiǧiterhan and Murray 2008; Yigiterhan et al. 2011) due to the more or less homogeneous geographical distribution of Al in the earth crust. Also, Al is supposed not to be influenced by anthropogenic emissions. Consequently, Al has been ubiquitously used as a reference element in many studies including aerosol composition investigations (Abrahim and Parker 2008; Rushdi et al. 2013, Gomes and Gillette 1993; Shelley et al. 2014).
The Me/Al ratios for ten selected elements at the 12 sampling locations are presented in Fig. 2 together with the Me/Al ratios of other local samples such as OD, Rd and STD. Also, the ratios were compared to the UCC as well. Me/Al ratios of these four reference samples were presented as horizontal lines in the figure.
All the presented metals show pronounced enrichment compared to the outdoor samples (OD and Rd) as well as the background compositions (STD, UCC). As it was expected from the correlation analysis Fe/Al, Mn/Al and V/Al ratios show homogeneous distribution among the sampling locations except for the S13 and S14 locations where iron and manganese are more enriched than at other locations. The other metals have significant variation among the sampling locations.
These findings support the idea that indoor dust is primarily transported from outdoor (Bavec et al. 2016; Zheng et al. 2018) and aggravated by indoor sources (Shraim et al. 2016; Tong 1998). The contribution of indoor sources explains the significant spatial variation of the composition even in neighbours’ locations such as S8–S9 or S10–S11.
Pollution evaluation
For a better understanding of the indoor air pollution composition, enrichment factors (EFs) were calculated using Eq. 1. This environmental index can give a clue for differentiating between anthropogenic and natural sources (Alghamdi et al. 2015; Li et al. 2017). Enrichment factors around 1 indicate the dominance crustal origin, while values higher than ten may indicate anthropogenic contribution (Kamaruzzaman et al. 2009). The higher the EF values, the more severe the anthropogenic influence.
In this study, EFs were used for the characterisation of the degree of elemental enrichments concerning the local surface terrestrial deposits (STD) considered as a background composition. The STD samples were collected from various land surface locations that reflect different proportions of typical Qatari geological formations such as rawdha, sabkha, lithosol, and sandy soils. Soils in Qatar contain small amounts of organic material and are generally calcareous and agriculturally unproductive and have very similar Me/Al ratios as the Qatari aeolian dust for most elements. Qatari STD is composed of two end-members: (1) a calcium carbonate (CaCO3) fraction that is relatively depleted in most other elements and (2) an aluminosilicate (Al2SiO5) fraction with a composition similar to UCC. More details of the STD samples can be found in Yigiterhan et al. (2018).
The indoor air pollution of the different locations was compared based on similarity analysis using multivariate statistical hierarchical clustering (Idris 2008; Souissi et al. 2001). In this method, each sampling location is represented as a point in the space of 23 dimensions (according to the 23 Me/Al variables). The distances between the points were calculated by the Euclidean distance formula. The two points with the smallest distance were linked, and their average Me/Al ratios were calculated. In the next step, a new distance matrix was calculated within the two linked points which were replaced by their average values (average linkage clustering method). The associated dendrogram that refers to the Euclidean distances between the data points was created using Minitab Software Version 18 (Fig. 3).
In figure, three typical groups can be distinguished. At most of the samples, the Me/Al ratios are close to each other, below the distance of 1.5. This group involves locations of S3, S4, S5, S6, S7, S8, S10 and S12. Locations S9 and S11 form a distinct group with a distance of 2.6. The distance of this group from the previous one is 2.7. The two industrial zone samples form the third group with a distance of 2.8. This group falls far from the previous group averages with a distance of 5.1.
Based on the previous classification of the samples, the EF group averages were calculated. Table 6 summarises the EFs for the three typical indoor environments (from ID1 to ID3) compared to OD and Rd enrichment factors. None of the locations shows enrichments concerning the elements of Ca, Mg, Na, K and Sr, which are the major components of the local earth crust.
The Rd sample shows significant enrichment of Zn (EF = 16.2) and Cu (EF = 14.3), which are two main tracers of the non-combustion traffic emission. Zinc is a component of the rubber tire. Thus, tire debris particles are enriched in Zn, while Cu is emitted to the atmosphere by the ware of brake pads (Apeagyei et al. 2011). The outdoor sample is also enriched by Zn and Cu that indicates the traffic influence on the urban outdoor dust. The EFs are lower compared to the road dust, which is directly affected by the traffic emission. All the indoor samples have significantly higher Zn, Cu and Ni enrichment factors (ranging from 20.7 to 131, 12.9 to 38.8 and 2.54 to 5.38, respectively) than the outdoor sample as a clear sign of the contribution of indoor sources. Rasmussen et al. (2001) studied elemental composition 22 indoor dust and soil samples from one city. They found that Cu, Zn and Ni concentrations were 9, 7 and three times higher in indoor dust than in outdoor soil. Tunno et al. (2016) have reviewed and summarised elemental compositions from different indoor sources. They concluded that the composition of indoor pollution could be attributed to two main source types: (1) combustion sources such as cooking, smoking and candle burning that generating Al-, Cd-, Fe-, Pb-, Mn-, and Zn-rich particles, and (2) other sources such as soil resuspension due to personal activity, hygiene and personal care products, as well as chemical cleaning agents, which are releasing Al-, Cd-, Cu-, Fe-, Pb-, V-, and Zn-rich particles.
Regarding the industrial zone samples (ID3), extremely high Zn enrichment factor was found (EF = 131). Since both offices at the industrial zone were affected by smoking, this high EF can be attributed to cigarette smoke or a workshop emission in the proximity.
Pb and Mo are also enriched in the road dust and outdoor sample due to traffic activity. Regarding the indoor samples, Pb is more enriched than outdoor, especially in the ID2 and ID3 sample groups. In the case of Mo, ID2 group is slightly more enriched than the Rd sample, while ID1 group shows depletion compared to the outdoor samples without considering the S12 sample which has extreme high Mo value (EF = 76.6) that exceeds even the EF from the industrial zone (EF = 18.2). The outlying Mo value of S12 was discharged from the group average and presented separately in the table (i.e. in the split cells of ID1).
Cd shows pronounced enrichment in all indoor samples, especially in ID2 and ID3 sample groups. The Cd EF is the lowest the ID1 group except for S7, where extremely high Cd EF was found (EF = 16.1). The outlying Cd value was discharged from the group average and presented separately in the split cell. The ID3 sample group, which contains samples from the industrial zone, is enriched by Fe, Mn, Ba, Cr, Co, and As. These elements are slightly or not enriched in the other indoor and outdoor samples; thus, we can attribute them to the industrial activity nearby the sampling locations.
Conclusions
In this study, the elemental composition of indoor dust samples retained by ACUs filters at various locations of Doha city has been analysed. The elemental composition of ACUs dust has been compared to the local outdoor dust deposit, road dust sample and the terrestrial surface composition. The analysed elements cover 20.6% of the total sample mass that is lower than in the case of outdoor samples. Supposing similar mineralogical composition of the particles, the lower mass percentage can be due to higher contribution from organic material originating from indoor sources.
In order to characterise the indoor samples, enrichment factors of the elements were calculated using aluminium as a reference element and STD as a reference composition. Zn, Cu and Ni significantly enriched the indoor ACUs dust samples than the outdoor samples. Also, pronounced enrichment of Pb and Cd was found. The higher enrichment factors compared to the outdoor samples might indicate contributions of indoor emissions.
The collected ACUs filter dust samples show the contribution of outdoor mineral particles, non-exhaust traffic emission, industrial sources, as well as the influence of indoor activity such as smoking.
References
Abbasi, M. N., & Tufail, M. (2013). Health risks assessment for heavy elements suspended in dusty air along Murree Highway, Pakistan. American-Eurasian Journal of Agricultural and Environmental Sciences,13(3), 372–377. https://doi.org/10.5829/idosi.aejaes.2013.13.03.232.
Abrahim, G. M. S., & Parker, R. J. (2008). Assessment of heavy metal enrichment factors and the degree of contamination in marine sediments from Tamaki Estuary, Auckland, New Zealand. Environmental Monitoring and Assessment,136(1–3), 227–238. https://doi.org/10.1007/s10661-007-9678-2.
Adamo, P., Arienzo, M., Imperato, M., Naimo, D., Nardi, G., & Stanzione, D. (2005). Distribution and partition of heavy metals in surface and sub-surface sediments of Naples city port. Chemosphere, 61(6), 800–809. https://doi.org/10.1016/j.chemosphere.2005.04.001.
Alghamdi, M. A., Almazroui, M., Shamy, M., Redal, M. A., Alkhalaf, A. K., Hussein, M. A., et al. (2015). Characterization and elemental composition of atmospheric aerosol loads during springtime dust storm in western Saudi Arabia. Aerosol and Air Quality Research,15(2), 440–453. https://doi.org/10.4209/aaqr.2014.06.0110.
Al-hemoud, A., Al-awadi, L., Al-rashidi, M., Abdul, K., Al-khayat, A., & Behbehani, W. (2017). Comparison of indoor air quality in schools: Urban vs. industrial ‘oil and gas’ zones in Kuwait. Building and Environment,122, 50–60. https://doi.org/10.1016/j.buildenv.2017.06.001.
Apeagyei, E., Bank, M., & Spengler, J. D. (2011). Distribution of heavy metals in road dust along an urban–rural gradient in Massachusetts. Atmospheric Environment,45, 2310. https://doi.org/10.1016/j.atmosenv.2010.11.015.
Bavec, S., Gosar, M., Miler, M., & Biester, H. (2016). Geochemical investigation of potentially harmful elements in household dust from a mercury-contaminated site, the town of Idrija (Slovenia). Environmental Geochemistry and Health,39, 443. https://doi.org/10.1007/s10653-016-9819-z.
Biegalski, S. R., Landsberger, S., & Hoff, R. M. (1998). Source-receptor modeling using trace metals in aerosols collected at three rural Canadian Great Lakes sampling stations. Journal of the Air and Waste Management Association,48, 227–237. https://doi.org/10.1080/10473289.1998.10463680.
Cao, Z., Chen, Q., Wang, X., Zhang, Y., Wang, S., Wang, M., et al. (2018). Contamination characteristics of trace metals in dust from different levels of roads of a heavily air-polluted city in North China. Environmental Geochemistry and Health,40(6), 2441–2452. https://doi.org/10.1007/s10653-018-0110-3.
Faiz, Y., Tufail, M., Javed, M. T., Chaudhry, M. M., & Naila-Siddique, (2009). Road dust pollution of Cd, Cu, Ni, Pb and Zn along Islamabad Expressway, Pakistan. Microchemical Journal,92(2), 186–192. https://doi.org/10.1016/j.microc.2009.03.009.
Ferwati, S., Skelhorn, C., Shandasb, V., Voelkelb, J., Shawisha, A., & Ghanim, M. (2017). Urban climate analysis of urban heat in a corridor environment—The case of Doha, Qatar. Urban Climate. https://doi.org/10.1016/j.uclim.2017.08.008.
Glorennec, P., Lucas, J. P., Mandin, C., & Le Bot, B. (2012). French children’s exposure to metals via ingestion of indoor dust, outdoor playground dust and soil: Contamination data. Environment International,45(1), 129–134. https://doi.org/10.1016/j.envint.2012.04.010.
Gomes, L., & Gillette, D. A. (1993). A comparison of characteristics of aerosol from dust storms in Central Asia with soil-derived dust from other regions. Atmospheric Environment Part A, General Topics, 27(16), 2539–2544. https://doi.org/10.1016/0960-1686(93)90027-V.
Grigoratos, T., & Martini, G. (2015). Brake wear particle emissions: A review. Environmental Science and Pollution Research,22(4), 2491–2504. https://doi.org/10.1007/s11356-014-3696-8.
Habil, M., Massey, D. D., & Taneja, A. (2016). Particles in different indoor microenvironments-its implications on occupants. Building and Environment,106, 237–244. https://doi.org/10.1016/j.buildenv.2016.06.036.
Han, X., & Lu, X. (2017). Spatial distribution, environmental risk and source of heavy metals in street dust from an industrial city in semi-arid area of China. Archives of Environmental Protection,43(2), 10–19. https://doi.org/10.1515/aep-2017-0013.
Huang, M., Wang, W., Yu, C., Chung, K., Bong, Y., Wang, X., et al. (2014). Science of the total environment contamination and risk assessment (based on bioaccessibility via ingestion and inhalation) of metal (loid) s in outdoor and indoor particles from urban centers of Guangzhou, China. Science of the Total Environment,479–480, 117–124. https://doi.org/10.1016/j.scitotenv.2014.01.115.
Idris, A. (2008). Combining multivariate analysis and geochemical approaches for assessing heavy metal level in sediments from Sudanese harbors along the Red Sea Coast. Microchemical Journal,90, 159. https://doi.org/10.1016/j.microc.2008.05.004.
Kamaruzzaman, B. Y., Hasrizal, B. S., Mohd Nizam, B. I., Ong, M. C., Jalal, K. C. A., & Shahbuddin, S. (2009). Geochemical proxy of sediment cores from Terengganu coastal water, Malaysia. Oriental Journal of Chemistry,25(1), 9–14.
Li, X., Poon, C., & Liu, P. S. (2001). Heavy metal concentration of urban soils and street dusts in Hong Kong. Applied Geochemistry,16, 1361–1368. https://doi.org/10.1016/S0883-2927(01)00045-2.
Li, Y., Zhang, Z., Zhou, H., Fan, Z., Wu, D., & Xia, B. (2017). Characteristics, sources and health risk assessment of toxic heavy metals in PM2.5 at a megacity of southwest China. Environmental Geochemistry and Health,38(2), 353–362. https://doi.org/10.1007/s10653-015-9722-z.
Mahfouz, M. M, Hassan, H. M., Yigiterhan, O., Elobaid, E. A., & Alfoldy, B. Z. (2018). PAH concentrations and exposure assessment from house dust retained in air-conditioning filters collected from Greater Doha, Qatar. Environmental Geochemistry and Health. https://doi.org/10.1007/s10653-019-00271-0.
Ministry of Development Planning and Statistics. (2014). Environment statistics annual report.
Nazir, R., Shaheen, N., & Shah, M. H. (2011). Indoor/outdoor relationship of trace metals in the atmospheric particulate matter of an industrial area. Atmospheric Research,101(3), 765–772. https://doi.org/10.1016/j.atmosres.2011.05.003.
Parveen, R., Saini, R., & Taneja, A. (2018). Chemical characterization and health risk assessment of soil and airborne particulates metals and metalloids in populated semiarid region, Agra, India. Environmental Geochemistry and Health,40(5), 2021–2035. https://doi.org/10.1007/s10653-016-9822-4.
Rasmussen, P. E. U., Subramanian, K. S., & Jessiman, B. J. (2001). A multi-element profile of housedust in relation to exterior dust and soils in the city of Ottawa, Canada. The Science of the Total Environment,267, 125–140.
Rudnick, R. L., & Gao, S. (2003). Composition of the continental crust. Treatise on Geochemistry, 3, 1–64. https://doi.org/10.1016/B0-08-043751-6/03016-4.
Rushdi, A. I., Al-Mutlaq, K. F., Al-Otaibi, M., El-Mubarak, A. H., & Simoneit, B. R. T. (2013). Air quality and elemental enrichment factors of aerosol particulate matter in Riyadh City, Saudi Arabia. Arabian Journal of Geosciences,6(2), 585–599. https://doi.org/10.1007/s12517-011-0357-9.
Sah, D., Verma, P. K., Kumari, K. M., & Lakhani, A. (2018). Chemical fractionation of heavy metals in fine particulate matter and their health risk assessment through inhalation exposure pathway. Environmental Geochemistry and Health. https://doi.org/10.1007/s10653-018-0223-8.
Saraga, D., Maggos, T., Sadoun, E., Fthenou, E., Hassan, H., Tsiouri, V., et al. (2017). Chemical characterization of indoor and outdoor particulate matter (PM2.5, PM10) in Doha, Qatar. Aerosol and Air Quality Research,17(5), 1156–1168. https://doi.org/10.4209/aaqr.2016.05.0198.
Sezgin, N., Ozcan, H. K., Demir, G., Nemlioglu, S., & Bayat, C. (2004). Determination of heavy metal concentrations in street dusts in Istanbul E-5 highway. Environment International,29(7), 979–985. https://doi.org/10.1016/S0160-4120(03)00075-8.
Shaari, H., Azmi, S. N. H. M., Sultan, K., Bidai, J., & Mohamad, Y. (2015). Spatial Distribution of Selected Heavy Metals in Surface Sediments of the EEZ of the East Coast of Peninsular Malaysia. International Journal of Oceanography. https://doi.org/10.1155/2015/618074.
Sharma, A., Massey, D. D., & Taneja, A. (2018). A study of horizontal distribution pattern of particulate and gaseous pollutants based on ambient monitoring near a busy highway Urban Climate. Urban Climate,24, 643–656. https://doi.org/10.1016/j.uclim.2017.08.003.
Shelley, R., Morton, P., & Landing, W. (2014). Elemental ratios and enrichment factors in aerosols from the US-GEOTRACES North Atlantic transects. Deep Sea Research Part II Topical Studies in Oceanography. https://doi.org/10.1016/j.dsr2.2014.12.005.
Shi, G., Chen, Z., Bi, C., Wang, L., Teng, J., Li, Y., et al. (2011). A comparative study of health risk of potentially toxic metals in urban and suburban road dust in the most populated city of China. Atmospheric Environment,45(3), 764–771. https://doi.org/10.1016/j.atmosenv.2010.08.039.
Shraim, A. M., Alenazi, D. A., & Kumar, P. (2016). Loading rates of dust and metals in residential houses of arid and dry climatic regions. Aerosol and Air Quality Research,16, 2462–2473. https://doi.org/10.4209/aaqr.2015.10.0611.
Siddique, N., Majid, A., & Tufail, M. (2011). Elemental analysis of dust trapped in air conditioner filters for the assessment of Lahore city’s air quality. Journal of Radioanalytical and Nuclear Chemistry,290, 691–699. https://doi.org/10.1007/s10967-011-1350-1.
Souissi, S., Ibanez, F., Hamadou, R. Ben, Boucher, J., Cathelineau, A. C., Blanchard, F., et al. (2001). A new multivariate mapping method for studying species assemblages and their habitats: Example using bottom trawl surveys in the Bay of Biscay (France). Sarsia,86(6), 527–542. https://doi.org/10.1080/00364827.2001.10420491.
Sutherland, R. A. (2000). Bed sediment-associated trace metals in an urban stream, Oahu, Hawaii. Environmental Geology, 39(6), 611–627. https://doi.org/10.1007/s002540050473.
Tan, J., Cheng, S. M., Loganath, A., Chong, Y. S., & Obbard, J. P. (2007). Polybrominated diphenyl ethers in house dust in Singapore. Chemosphere,66(6), 985–992. https://doi.org/10.1016/j.chemosphere.2006.07.052.
Thorpe, A., & Harrison, R. M. (2008). Sources and properties of non-exhaust particulate matter from road traffic: A review. Science of the Total Environment,400(1–3), 270–282. https://doi.org/10.1016/j.scitotenv.2008.06.007.
Tong, S. T. Y. (1998). Indoor and outdoor household dust contamination in Cincinnati, Ohio, USA. Environmental Geochemistry and Health,20(3), 123–133. https://doi.org/10.1023/A:1006561832381.
Tunno, B. J., Dalton, R., Cambal, L., Holguin, F., Lioy, P., & Clougherty, J. E. (2016). Indoor source apportionment in urban communities near industrial sites. Atmospheric Environment,139, 30–36. https://doi.org/10.1016/j.atmosenv.2016.04.039.
Visschedijk, A. J. H., Denier van der Gon, H., Hulskotte, J., & Quass, U. (2012). Anthropogenic Vanadium emissions to air and ambient air concentrations in North-West Europe. In E3S web of conferences (Vol. 1). https://doi.org/10.1051/e3sconf/20130103004.
Yigiterhan, O., Alfoldy, B. Z., Giamberini, M., Turner, J. C., Al-Ansari, E. S., Abdel-Moati, M. A., et al. (2018). Geochemical composition of Aeolian dust and surface deposits from the Qatar Peninsula. Chemical Geology,476(2018), 24–45. https://doi.org/10.1016/j.chemgeo.2017.10.030.
Yiǧiterhan, O., & Murray, J. W. (2008). Trace metal composition of particulate matter of the Danube River and Turkish rivers draining into the Black Sea. Marine Chemistry,111(1–2), 63–76. https://doi.org/10.1016/j.marchem.2007.06.019.
Yigiterhan, O., Murray, J. W., & Tugrul, S. (2011). Trace metal composition of suspended particulate matter in the water column of the Black Sea. Marine Chemistry,126(1–4), 207–228. https://doi.org/10.1016/j.marchem.2011.05.006.
Zheng, Na, Liu, J., Wang, Q., & Liang, Z. (2010). Science of the total environment health risk assessment of heavy metal exposure to street dust in the zinc smelting district, Northeast of China. Science of the Total Environment,408(4), 726–733. https://doi.org/10.1016/j.scitotenv.2009.10.075.
Zheng, N., Yu, Y., Hou, S., Xu, S., Tang, L., & Ji, X. (2018). Contamination assessment and health risk of arsenic exposure to stairway dust in the zinc smelting district. Northeast China: Environmental Geochemistry and Health. https://doi.org/10.1007/s10653-018-0166-0.
Acknowledgements
Open Access funding provided by the Qatar National Library. This publication was made possible by the NPRP award (NPRP 8-202-3-043) from the Qatar National Research Fund (QNRF), a member of Qatar Foundation. The statements made herein are solely the responsibility of the authors. Thanks are also due to Prof. Jeffery Obbard for his continual support during preparing of the article, the Director of the ESC Prof. Hamad S. Al Kawari, the technical manger Mrs. Hajer Al-Niami, and all the technical staff of the ESC.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Appendix 1: The detailed chemical analysis results of the ACUs filter dust samples
Appendix 1: The detailed chemical analysis results of the ACUs filter dust samples
Sample | Al | Ca | Mg | Fe | Na | K | Ti | Zn | P | Sr | Mn | Ba |
---|---|---|---|---|---|---|---|---|---|---|---|---|
% | % | % | % | % | % | % | ppm | ppm | ppm | ppm | ppm | |
S3 | 2.39 | 11.76 | 3.06 | 1.69 | 1.11 | 0.73 | 0.18 | 306 | 647 | 466 | 289 | 349 |
S4 | 2.08 | 17.23 | 2.69 | 1.68 | 1.19 | 0.80 | 0.19 | 368 | 458 | 584 | 297 | 313 |
S5 | 2.27 | 10.38 | 2.27 | 1.69 | 1.52 | 0.93 | 0.14 | 257 | 659 | 414 | 297 | 243 |
S6 | 3.23 | 10.39 | 2.64 | 2.39 | 0.33 | 0.85 | 0.23 | 404 | 815 | 349 | 330 | 292 |
S7 | 1.43 | 8.11 | 1.73 | 1.08 | 1.22 | 0.89 | 0.10 | 315 | 589 | 283 | 192 | 184 |
S8 | 1.71 | 14.93 | 2.27 | 1.29 | 1.24 | 0.76 | 0.16 | 636 | 738 | 523 | 208 | 271 |
S9 | 1.52 | 13.53 | 2.03 | 1.30 | 1.23 | 0.70 | 0.37 | 908 | 643 | 427 | 209 | 276 |
S10 | 1.94 | 9.16 | 2.11 | 1.36 | 1.06 | 0.78 | 0.11 | 337 | 465 | 347 | 234 | 207 |
S11 | 0.85 | 6.79 | 1.42 | 0.74 | 0.83 | 0.45 | 0.09 | 457 | 415 | 238 | 132 | 177 |
S12 | 1.98 | 9.75 | 2.59 | 1.42 | 1.07 | 0.71 | 0.14 | 656 | 800 | 390 | 258 | 220 |
S13 | 1.67 | 14.30 | 2.91 | 4.60 | 1.34 | 0.66 | 0.16 | 2824 | 565 | 528 | 716 | 566 |
S14 | 2.68 | 14.87 | 3.30 | 5.37 | 1.35 | 0.89 | 0.21 | 2423 | 700 | 585 | 1275 | 682 |
Mean | 1.98 | 11.77 | 2.42 | 2.05 | 1.12 | 0.76 | 0.17 | 824.25 | 624.50 | 427.83 | 369.75 | 315.00 |
SD | 0.62 | 3.19 | 0.55 | 1.44 | 0.30 | 0.13 | 0.08 | 865.11 | 131.28 | 113.23 | 320.38 | 155.19 |
CV (%) | 31.50 | 27.10 | 22.80 | 70.06 | 27.05 | 17.05 | 43.48 | 104.96 | 21.02 | 26.47 | 86.65 | 49.27 |
Range | 2.38 | 10.44 | 1.88 | 4.63 | 1.19 | 0.48 | 0.28 | 2567.00 | 400.00 | 347.00 | 1143.00 | 505.00 |
Sample | Cu | Cr | Ni | Pb | V | Mo | Li | Co | Sb | As | Cd | Be |
---|---|---|---|---|---|---|---|---|---|---|---|---|
ppm | ppm | ppm | ppm | ppm | ppm | ppm | ppm | ppm | ppm | ppm | ppm | |
S3 | 145 | 71.4 | 66.9 | 30.8 | 68.2 | 3.2 | 14.1 | 10.0 | 10.2 | 4.98 | 0.53 | 0.48 |
S4 | 153 | 89.8 | 57.6 | 36.5 | 56.8 | 4.0 | 13.7 | 9.8 | 12.2 | 7.01 | 0.62 | 0.49 |
S5 | 109 | 72.5 | 65.9 | 20.6 | 55.2 | 3.2 | 14.6 | 9.8 | 9.8 | 8.08 | 0.65 | 0.62 |
S6 | 131 | 92.2 | 79.9 | 38.4 | 72.0 | 3.5 | 18.4 | 12.8 | 10.1 | 5.17 | 0.63 | 0.88 |
S7 | 98.0 | 53.6 | 46.2 | 26.4 | 37.9 | 2.8 | 9.0 | 6.6 | 10.1 | 3.12 | 1.26 | 0.39 |
S8 | 149 | 108 | 43.6 | 37.6 | 43.7 | 8.7 | 9.2 | 7.9 | 11.7 | 4.03 | 0.59 | 0.39 |
S9 | 177 | 102 | 53.1 | 49.1 | 47.3 | 6.8 | 8.9 | 15.0 | 14.3 | 3.14 | 0.84 | 0.33 |
S10 | 99.1 | 60.9 | 57.6 | 19.6 | 45.9 | 4.0 | 11.1 | 8.2 | 11.2 | 4.19 | 0.33 | 0.47 |
S11 | 234 | 35.7 | 48.4 | 42.9 | 25.7 | 2.6 | 5.0 | 4.9 | 12.2 | 1.97 | 0.59 | 0.14 |
S12 | 190 | 62.9 | 56.1 | 30.0 | 49.3 | 96.1 | 13.7 | 8.4 | 7.7 | 3.88 | 0.55 | 0.51 |
S13 | 374 | 158 | 116.4 | 158.3 | 47.6 | 24.7 | 13.8 | 25.6 | 21.5 | 13.1 | 0.89 | 0.33 |
S14 | 455 | 195 | 132.1 | 292.9 | 75.6 | 22.1 | 19.7 | 29.0 | 23.1 | 27.2 | 0.99 | 0.69 |
Mean | 192.84 | 91.83 | 68.65 | 65.26 | 52.10 | 15.14 | 12.60 | 12.33 | 12.84 | 7.16 | 0.71 | 0.48 |
SD | 111.98 | 45.32 | 28.01 | 80.66 | 14.45 | 26.60 | 4.18 | 7.51 | 4.72 | 6.98 | 0.25 | 0.19 |
CV (%) | 58.07 | 49.35 | 40.80 | 123.61 | 27.74 | 175.68 | 33.19 | 60.86 | 36.74 | 97.48 | 35.21 | 40.08 |
Range | 357.00 | 159.30 | 88.50 | 273.30 | 49.90 | 93.50 | 14.70 | 24.10 | 15.40 | 25.23 | 0.93 | 0.74 |
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Mahfouz, M.M., Yigiterhan, O., Elnaiem, A.E. et al. Elemental compositions of particulate matter retained on air condition unit’s filters at Greater Doha, Qatar. Environ Geochem Health 41, 2533–2548 (2019). https://doi.org/10.1007/s10653-019-00304-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10653-019-00304-8