Abstract
Surface texturing has been an attracting interest in metal cutting fields because of their tribological improvement at the tool–chip interface. A novel symmetric conical micro-grooved texture (S-5) was proposed and manufactured on the tool rake face using laser texture technology. The improvement effect of surface texturing (S-5) on tool–chip friction property was tested with AISI 1045 steel cutting experiment for various cutting speeds (80 to 160 m/min) under flood lubrication condition. Meanwhile, cutting performance of S-5 were evaluated against parallel micro-grooved texture tools (P-0) for a better clarification of the interaction mechanism. Experimental results indicated that surface texturing (P-0, S-5) on tool rake face all successfully resulted in a reduced cutting force, tool–chip friction coefficient, and tool surface wear than conventional tools (C-0). Moreover, S-5 showed a more obvious advantage in the improvement of tool–chip interfacial friction property than P-0.When cutting speed was smaller than 120 m/min, the friction coefficient obtained with the conventional (C-0) and textured tools (P-0, S-5) all showed a downward trend, and a smallest friction coefficient was appeared for S-5. When the cutting speed was greater than 120 m/min, an upward trend of friction coefficient was obtained for the C-0 and P-0 tools. However, a downward trend of friction coefficient was still existed for S-5. Detailed research indicated that the symmetric conical micro-grooved texture on the tool rake face could accelerate the infiltration speed of cutting fluid at the tool–chip interface. More cutting fluid would be supplied and stored at the tool–chip interface. So, symmetric conical micro-grooved texture on the tool rake face had a best lubrication effect of cutting fluid than conventional (C-0) and parallel micro-grooved texture tools (P-0).
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Astakhov VP (2006) Tribology of metal cutting, 1th edn. Elsevier, London
Bailey JA (1975) Friction in metal machining - mechanical aspects. Wear 31:243–275
Ozlu E, Budak E, Molinari A (2009) Analytical and experimental investigation of rake contact and friction behavior in metal cutting. Int J Mach Tool Manu 49:865–875
Kim DY, Kim DM, Park HW (2018) Predictive cutting force model for a cryogenic machining process incorporating the phase transformation of Ti-6Al-4V. Int J Adv Manuf Technol 96(1–4):1293–1304
Hwang J (2014) Direct observation of fluid action at the chip-tool interface in machining. Int J Precis Eng Manuf 15:2041–2049
Gachot C, Rosenkranz A, Hsu SM, Costa HL (2017) A critical assessment of surface texture for friction and wear improvement. Wear 372-373:21–41
Krolczyk GM, Nieslony P, Maruda RW, Wojciechowski S (2017) Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production. J Clean Prod 142:3343–3354
Gariani S, Shyha I, Inam F, Huo D (2018) Experimental analysis of system parameters for minimum cutting fluid consumption when machining Ti-6Al-4V using a novel supply system. Int J Adv Manuf Technol 95(5–8):2795–2809
Evans CJ, Bryan JB (1999) “Structured”, “textured” or “engineered” surfaces. Ann CIRP 48(2):541–556
Ryk G, Etsion I (2006) Testing piston rings with partial laser surface texturing for friction reduction. Wear 261:792–796
Kovalchenko A, Ajayi O, Erdemir A, Fenske G (2011) Friction and wear behavior of laser textured surface under lubricated in initial point contact. Wear 271(9–10):1719–1725
Li JL, Xiong DS, Dai JH, Huang ZJ, Tyagi R (2010) Effect of surface laser texture on frictional properties of nickel-based composite. Tribol Int 143:1193–1199
Hiraoka N, Sasaki A (1997) Effect of discontinuous hard under-coating on the life of solid film lubricant under extreme contact pressure. Tribol Int 30:429–434
Rahmani R, Mirzaee I, Shirvani A, Shirvani H (2010) An analytical approach for analysis and optimization of slider bearings with infinite width parallel textures. Tribol Int 43:1551–1565
Wang XL, Kato K, Adachi K, Aizawa K (2003) Load carrying capacity map for the surface texture design of SiC thrust bearing sliding in water. Tribol Int 36:189–197
Sinanoglu C (2009) Investigation of load carriage capacity of journal bearings by surface texture. Ind Lubr Tribol 61:261–270
Arslan A, Masjuki HH, Kalam MA (2016) Surface texture manufacturing techniques and tribological effect of surface texture on cutting tool performance: a review. Crit Rev Solid State Mater Sci 0:1–35
Sharma V, Pandey PM (2016) Recent advances in turning with textured cutting tools: a review. J Clean Prod 137:701–715
Koshy P, Tovey J (2011) Performance of electrical discharge textured cutting tools. Int J Adv Manuf Technol 60:153–156
Enomoto T, Sugihara T (2011) Improvement of anti-adhesive properties of cutting tool by nano/micro textures and its mechanism. Procedia Eng 19:100–105
Enomoto T, Sugihara T (2010) Improving anti-adhesive properties of cutting tool surfaces by nano−/micro-textures. CIRP Ann Manuf Technol 59:597–600
Obikawa T, Kamio A, Takaoka H, Osada A (2011) Micro-texture at the coated tool face for high performance cutting. Int J Mach Tool Manuf 51:966–972
Zhang K, Deng JX, Xing YQ, Li S, Gao H (2015) Effect of microscale texture on cutting performance of WC/co-based TiAlN coated tools under different lubrication conditions. Appl Surf Sci 326:107–118
Michielsen S, Zhang JL, Du JM, Lee HJ (2011) Gibbs free energy of liquid drops on conical fibers. Langmuir 27:11867–11872
Liu JL, Xia R, Li BG, Feng XQ (2007) Directional motion of droplet in a conical tube or on a conical fiber. Chin Phys Lett 24:3210–3213
Radoslaw WM, Grzegorz MK, Mariusz M, Piotr N, Szymon W (2017) Structural and microhardness changes after turning of the AISI 1045 steel for minimum quantity cooling lubrication. J Mater Eng Perform 26(1):431–438
Lee EH, Shaffer BW (1951) The theory of plasticity applied to a problem of machining. J Appl Mech 18:405–413
Krolczyka GM, Marudab RW, Krolczyka JB, Nieslonya P, Wojciechowskic S, Legutko S (2018) Parametric and nonparametric description of the surface topography in the dry and MQCL cutting conditions. Measurement 121:225–239
Huang CH, Lee S, Sullivan JP, Chandrasekar S (2007) In situ measurement of fluid film thickness in machining. Tribol Lett 28(1):39–44
Wen SZ (2002) Principles of tribology, 2th edn. Tsinghua University Press, Beijing
Funding
This study was supported by the key scientific and technological project of Henan province (grant no. 162102210104).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Rights and permissions
About this article
Cite this article
Pang, M., Nie, Y. & Ma, L. Effect of symmetrical conical micro-grooved texture on tool–chip friction property of WC-TiC/Co cemented carbide tools. Int J Adv Manuf Technol 99, 737–746 (2018). https://doi.org/10.1007/s00170-018-2498-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2498-4