Abstract
Nickel-based alloy Inconel718 is one kind of complex alloy with multiple components. There is complex cutting deformation (shear localization of material) in high-speed cutting process. The chip shows a serrated shape. Through analyzing the chip morphology, the change of microstructure and development of shear band is analyzed, and the formation mechanism of the shear band is revealed. Based on the formation mechanism of shear band, the coupled elastoplastic-damage constitutive model is proposed to describe the shear stress during the cutting process. The shear band width has been determined by micrographic observations and theoretical model calculation. The experimental and theoretical results show that the shear band width in chip formation decreases linearly with an increase in the cutting speed.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Zhu DH, Zhang XM, Ding H (2013) Tool wear characteristics in machining of nickel-based superalloys. Int J Mach Tool Manu 64:60–77
Fan YH, Hao ZP, Zheng ML, Sun FL, Yang SC (2013) Study of surface quality in machining nickel-based alloy Inconel 718. Int J Adv Manuf Technol 69:2659–2667
Venkatesan K, Ramanujam R, Kuppan P (2017) Investigation of machinability characteristics and chip morphology study in laser-assisted machining of Inconel 718. Int J Adv Manuf Technol 91:3807–3821
Costes JP, Guillet Y, Poulachon G, Dessoly M (2007) Tool-life and wear mechanisms of CBN tools in machining of Inconel 718. Int J Mach Tools Manuf 47(7–8):1081–1087
Gao D, Hao ZP, Han RD, Chang YL, Muguthu JN (2011) Study of cutting deformation in machining nickel-based alloy Inconel 718. Int J Mach Tool Manu 51(6):520–527
Komnaduri R, Schroeder T (1986) On hear instability in machining nickel-iron base superalloy. J Eng Ind 108:93–100
Hou ZB, Komanduri R (1997) Modeling of thermo mechanical shear instability in machining. Int J Mech Sci 39(11):1273–1314
Pawade RS, Sonawane HA, Joshi SS (2009) An analytical model to predict specific shear energy in high-speed turning of Inconel718. Int J Mach Tool Manu 49(12):979–990
Shockey DA, Simons JW, Brown CS, Kobayashi T (2007) Shear failure of Inconel 718 under dynamic loads. Exp Mech 47:723–732
Molinari A, Musquar C, Sutter G (2002) Adiabatic shear banding in high speed machining of Ti–6Al–4V: experiments and modeling. Int J Plast 18:443–459
Burns TJ, Davies MA (2002) On repeated adiabatic shear band formation during high-speed machining. Int J Plast 18:487–506
Perzyna P (1994) Instability phenomena and adiabatic shear band localization in thermoplastic flow processes. Acta Mech 106(3–4):173–205
Ye GG, Xue SF, Jiang MQ, Tong XH, Dai LH (2013) Modeling periodic adiabatic shear band evolution during high speed machining Ti-6Al-4V alloy. Int J Plast 40:39–55
Meyers MA, Nesterenko VF, LaSalvia JC, Xue Q (2001) Shear localization in dynamic deformation of materials: microstructural evolution and self-organization. Mater Sci Eng A 317(1–2):204–225
Xue Q, Meyers MA, Nesterenko VF (2002) Self-organization of shear bands in titanium and Ti-6Al-4V alloy. Acta Mater 50:575–596
Xue Q, Meyers MA, Nesterenko VF (2004) Self organization of shear bands in stainless steel. Mater Sci Eng A 384:35–46
Zhou F, Wright TW, Ramesh KT (2006) The formation of multiple adiabatic shear bands. J Mech Phys Solids 54:1376–1400
Hines JA, Vecchio KS, Ahzi S (1998) A model for microstructure evolution in adiabatic shear bands. Metall Mater Trans A 29(1):191–203
Li Q, Xu YB, Lai ZH, Shen LT, Bai YL (2000) Dynamic recrystallization induced by plastic deformation at high strain rate in a Monel alloy. Mater Sci Eng A 276:250–256
Wang XY, Huang CZ, Zou B, Liu HL, Zhu HT, Wang J (2013) Dynamic behavior and a modified Johnson-Cook constitutive model of Inconel718 at high strain rate and elevated temperature. Mater Sci Eng A 580:385–390
Liang X (2007) Damage accumulation and fracture initiation in uncracked ductile solids subject to triaxial loading. Int J Solids Struct 44:5163–5181
Erice B, Gálvez F (2014) A coupled elastoplastic-damage constitutive model with Lode angle dependent failure criterion. Int J Solids Struct 51:93–110
Gruben G, Fagerholt E, Hopperstad OS, Bovik T (2011) Fracture characteristics of a cold-rolled dual-phase steel. Eur J Mech A Solids 30:204–218
Yang QB, Liu ZQ, Shi ZY, Wang B (2014) Analytical modeling of adiabatic shear band spacing for serrated chip in high-speed machining. Int J Adv Manuf Technol 71(9–12):1901–1908
Funding
This work is supported by the National Natural Science Foundation of China: (51505038) and the Science and Technology project of Education Department of Jilin Province (JJKH20170564KJ, JJKH20170562KJ).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Hao, Z., Cui, R. & Fan, Y. Formation mechanism and characterization of shear band in high-speed cutting Inconel718. Int J Adv Manuf Technol 98, 2791–2799 (2018). https://doi.org/10.1007/s00170-018-2435-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2435-6