Abstract
A Nitinol hydraulic bellows actuator for the application in minimally invasive surgeries (MIS) has been designed and manufactured. Such application required the actuator to be elastically deformable. This paper explains how the actuator geometry is optimized for large deformations and shows the feasibility of an actuator manufactured by selective laser melting (SLM). Four different shapes were virtually tested using finite element analyses (FEA). Furthermore, multiple samples of the bellows actuator with a U-shaped deformation zone were simulated and manufactured. A test rig was developed to measure deformation and achievable force. Physical tests showed a sufficient performance of the actuator for typical applications in minimal invasive surgery. Technical challenges and potential solutions on the current state of development are discussed.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Westebring-van der Putten EP, van den Dobbelsteen JJ, Goossens RHM, Jakimowicz JJ, Dankelman J (2009) Effect of laparoscopic grasper force transmission ratio on grasp control. Surg Endosc 23(4):818–824. https://doi.org/10.1007/s00464-008-0107-6
Cuntz T (2015) Untersuchungen zur Eignung mikrohydraulischer Antriebe für die minimal invasive Chirurgie. Dissertation
Carus T (2014) Operationsatlas Laparoskopische Chirurgie. Springer
de Volder M, Reynaerts D (2010) Pneumatic and hydraulic microactuators: a review. J Micromech Microeng 20(4):43001. https://doi.org/10.1088/0960-1317/20/4/043001
Ikuta K, Ichikawa H, Suzuki K et al (2006) Multi-degree of freedom hydraulic pressure driven safety active catheter. In: ICRA ‘06: Proceedings of the 2006 IEEE International Conference on Robotics and Automation, pp 4161–4166
Kang H-W, Lee IH, Cho D-W (2006) Development of a micro-bellows actuator using micro-stereolithography technology. Microelectron Eng 83:1201–1204
Spindler C, Kaltenbacher D, Schächtele J (2013) Powerful micro-actuators for (flexible) surgical instrument tips. BMT
Haberland C (2012) Additive Verarbeitung von NiTi-Formgedächtniswerkstoffen mittels selective laser melting. Dissertation
Van Humbeeck J (2001) Shape memory alloys: a material and a technology. Adv Eng Mater 3:837–850
Krishna BV, Bose S, Bandyopadhyay A (2009) Fabrication of porous NiTi shape memory alloy structures using laser engineered net shaping. J Biomed Mater Res 89((2):481–490. https://doi.org/10.1002/jbm.b.31238
Krone L (2005) Metal-injection-moulding (MIM) von NiTi Bauteilen mit Formgedächtniseigenschaften. Dissertation
Bormann T, Schumacher R, Müller B, Mertmann M, de Wild M (2012) Tailoring selective laser melting process parameters for NiTi implants. J Mater Eng Perform
Acknowledgements
The authors acknowledge the Fraunhofer Institute for Laser Technology (ILT) for the SLM fabrication of the actuator prototypes used in the present study.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Spindler, C., Juhre, D. Development of a shape memory alloy actuator using generative manufacturing. Int J Adv Manuf Technol 97, 4157–4166 (2018). https://doi.org/10.1007/s00170-018-2153-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2153-0