Abstract
High cooling rates within the selective laser melting (SLM) process can generate large residual stresses within fabricated components. Understanding residual stress development in the process and devising methods for in-situ reduction continues to be a challenge for industrial users of this technology. Computationally efficient FEA models representative of the process dynamics (temperature evolution and associated solidification behaviour) are necessary for understanding the effect of SLM process parameters on the underlying phenomenon of residual stress build-up. The objective of this work is to present a new modelling approach to simulate the temperature distribution during SLM of Ti6Al4V, as well as the resulting melt-pool size, solidification process, associated cooling rates and temperature gradients leading to the residual stress build-up. This work details an isotropic enhanced thermal conductivity model with the SLM laser modelled as a penetrating volumetric heat source. An enhanced laser penetration approach is used to account for heat transfer in the melt-pool due to Marangoni convection. Results show that the developed model was capable of predicting the temperature distribution in the laser/powder interaction zone, solidification behaviour, the associated cooling rates, melt-pool width (with 14.5% error) and melt-pool depth (with 3% error) for SLM Ti6Al4V. The model was capable of predicting the differential solidification behaviour responsible for residual stress build-up in SLM components. The model-predicted trends in cooling rates and temperature gradients for varying SLM parameters correlated with experimentally measured residual stress trends. Thus, the model was capable of accurately predicting the trends in residual stress for varying SLM parameters. This is the first work based on the enhanced penetrating volumetric heat source, combined with an isotropic enhanced thermal conductivity approach. The developed model was validated by comparing FEA melt-pool dimensions with experimental melt-pool dimensions. Secondly, the model was validated by comparing the temperature evolution along the laser scan path with experimentally measured temperatures from published literature.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Burns M (1993) Automated fabrication: improving productivity in manufacturing. Prentice Hall, Englewood Cliffs
Gibson I, Rosen DW, Stucker B (2009) Additive manufacturing technologies: rapid prototyping to direct digital manufacturing. Springer. pp.1–14
Casavola C, Campanelli S.L., Pappalettere C (2008) Experimental analysis of residual stresses in the selective laser melting process. In Proceedings of the XIth International Congress and Exposition. Orlando, Florida, USA
Kruth J-P, Deckers J, Yasa E, Wauthlé R (2012) Assessing and comparing influencing factors of residual stresses in selective laser melting using a novel analysis method. Proc Inst Mech Eng B J Eng Manuf 226(6):980–991
Zaeh MF, Branner G (2010) Investigations on residual stresses and deformations in selective laser melting. Production Engineering : research and development in Germany 4(1)
Van Belle LV, Boyer G, Claude J (2013) Investigation of residual stresses induced during the selective laser melting process. Key Eng Mater 554-557:1828–1834
Tatsuaki Furumoto TU, Aziz MSA, Hosokawa A, Tanaka R (2010) Study on reduction of residual stress induced during rapid tooling process—influence of heating conditions on residual stress. Key Eng Mater 487-488:785–789
Roberts IA (2012) Investigation of residual stresses in the laser melting of metal powders in additive layer manufacturing, University of Wolverhampton. p. 246
Joe Elambasseril SF, Bringezu M, Brandt M (2012) Influence of process parameters on selective laser melting of Ti 6Al-4V components, RMIT University School of Aerospace, Mechanical and Manufacturing Engineering (SAMME)
Verhaeghe F, Craeghs T, Heulens J, Pandelaers L (2009) A pragmatic model for selective laser melting with evaporation. Acta Mater 57(20):6006–6012
Khairallah SA, Anderson A (2014) Mesoscopic simulation model of selective laser melting of stainless steel powder. J Mater Process Technol 214(11):2627–2636
Ali H, Ma L, Ghadbeigi H, Mumtaz K (2017) In-situ residual stress reduction, martensitic decomposition and mechanical properties enhancement through high temperature powder bed pre-heating of selective laser melted Ti6Al4V. Mater Sci Eng A 695:211–220
Chatterjee AN, Kumar S, Saha P, Mishra PK, Choudhury RA (2003) An experiment design approach to selective laser sintering of low carbon steel. J Mater Process Technol 136:151–157
Facchini L, Magalini E, Robotti P, Molinari A, Höges S, Wissenbach K (2010) Ductility of a Ti-6Al-4V alloy produced by selective laser melting of prealloyed powders. Rapid Prototyp J 16(6):450–459
Gusarov AV, Pavlov M, Smurov I (2011) Residual stresses at laser surface remelting and additive manufacturing. Phys Procedia 12:248–254
Hanzl P, Zetek M, Bakša T, Kroupa T (2015) The influence of processing parameters on the mechanical properties of SLM parts. Procedia Eng 100:1405–1413
Fu C, Guo Y (2014) 3-Dimensional finite element modeling of selective laser melting Ti-6Al-4V alloy. in Solid Freeform Fabrication Symposium 2014 Proceedings
Safdar S, Pinkerton AJ, Li L, Sheikh MA, Withers PJ (2013) An anisotropic enhanced thermal conductivity approach for modelling laser melt pools for Ni-base super alloys. Appl Math Model 37(3):1187–1195
Dai K, Li XX, Shaw LL (2004) Comparisons between thermal modeling and experiments: effects of substrate preheating. Rapid Prototyp J 10(1):24–34
Qian L, Mei J, Wu XH (2007) An experimental and modelling study of laser fabricated samples. Mater Sci Forum Trans Tech Publ 539-543:3637–3642
Shiomi M, Yoshidome A, Abe F, Osakada K (1999) Finite element analysis of melting and solidifying processes in laser rapid prototyping of metallic powders. Int J Mach Tools Manuf 39(2):237–252
Matsumoto M, Shiomi M, Osakada K, Abe F (2002) Finite element analysis of single layer forming on metallic powder bed in rapid prototyping by selective laser processing. Int J Mach Tools Manuf 42(1):61–67
Katzarov I, Malinov S, Sha W (2002) Finite element modeling of the morphology of β to α phase transformation in Ti-6Al-4V alloy. Metall Mater Trans A 33(4):1027–1040
Cheng B, Chou K (2015) Melt pool evolution study in selective laser melting. In 26th Annual International Solid Freeform Fabrication Symposium-An Additive Manufacturing Conference, Austin, TX, USA
Fischer P, Karapatis N, Romano V, Glardon R, Weber HP (2002) A model for the interaction of near-infrared laser pulses with metal powders in selective laser sintering. Appl Phys A 74(4):467–474
Gusarov AV, Smurov I (2010) Modeling the interaction of laser radiation with powder bed at selective laser melting. Phys Procedia 5:381–394
Antony K, Arivazhagan N, Senthilkumaran K (2014) Numerical and experimental investigations on laser melting of stainless steel 316L metal powders. J Manuf Process 16(3):345–355
Song B, Dong S, Liao H, Coddet C (2012) Process parameter selection for selective laser melting of Ti6Al4V based on temperature distribution simulation and experimental sintering. Int J Adv Manuf Technol 61(9):967–974
Polivnikova T (2015) Study and modelling of the melt pool dynamics during selective laser sintering and melting, EPFL
Dai K, Shaw L (2004) Thermal and mechanical finite element modeling of laser forming from metal and ceramic powders. Acta Mater 52(1):69–80
Papadakis L, Loizou A, Risse J, Bremen S (2013) A thermo-mechanical modeling reduction approach for calculating shape distortion in SLM manufacturing for aero engine components. Proceedings of the 6th International Conference on Advanced Research in Virtual and Rapid Prototyping, Leiria. pp. 1–5
Roberts IA, Wang CJ, Esterlein R, Stanford M, Mynors DJ (2009) A three-dimensional finite element analysis of the temperature field during laser melting of metal powders in additive layer manufacturing. Int J Mach Tools Manuf 49(12–13):916–923
Gusarov AV, Smurov I (2009) Two-dimensional numerical modelling of radiation transfer in powder beds at selective laser melting. Appl Surf Sci 255(10):5595–5599
Lopez-Botello O, Martinez-Hernandez U, Ramírez J, Pinna C, Mumtaz K (2017) Two-dimensional simulation of grain structure growth within selective laser melted AA-2024. Mater Des 113:369–376
Parry L, Ashcroft IA, Wildman RD (2016) Understanding the effect of laser scan strategy on residual stress in selective laser melting through thermo-mechanical simulation. Addit Manuf 12(Part A):1–15
Mills K et al (1998) Marangoni effects in welding. Philosophical Transactions-Royal Society of London Series A Mathematical Physical and Engineering Sciences, p. 911–926
Yuan P, Gu D (2015) Molten pool behaviour and its physical mechanism during selective laser melting of TiC/AlSi10Mg nanocomposites: simulation and experiments. J Phys D Appl Phys 48(3):035303
Cheng B, Shrestha S, Chou K (2016) Stress and deformation evaluations of scanning strategy effect in selective laser melting. Addit Manuf 12(Part B):240–251
Donachie MJ (2000) Titanium: a technical guide, 2nd Edition. ASM International
Shi Y, Shen H, Yao Z, Hu J (2007) Temperature gradient mechanism in laser forming of thin plates. Opt Laser Technol 39(4):858–863
Tolochko NK, Khlopkov YV, Mozzharov SE, Ignatiev MB, Laoui T, Titov VI (2000) Absorptance of powder materials suitable for laser sintering. Rapid Prototyp J 6(3):155–161
Vasinonta A, Beuth JL, Griffith M (2006) Process maps for predicting residual stress and melt pool size in the laser-based fabrication of thin-walled structures. J Manuf Sci Eng 129(1):101–109
Simchi A (2006) Direct laser sintering of metal powders: mechanism, kinetics and microstructural features. Mater Sci Eng A 428(1):148–158
Yadroitsev I, Krakhmalev P, Yadroitsava I (2014) Selective laser melting of Ti6Al4V alloy for biomedical applications: temperature monitoring and microstructural evolution. J Alloys Compd 583:404–409
Alimardani M, Toyserkani E, Huissoon JP, Paul CP (2009) On the delamination and crack formation in a thin wall fabricated using laser solid freeform fabrication process: an experimental–numerical investigation. Opt Lasers Eng 47(11):1160–1168
Manvatkar V, De A, DebRoy T (2015) Spatial variation of melt pool geometry, peak temperature and solidification parameters during laser assisted additive manufacturing process. Mater Sci Technol 31(8):924–930
Mercelis P (2007) Control of selective laser sintering and selective laser melting processes. KU Leuven, Leuven, Belgium
Shiomi M, Osakada K, Nakamura K, Yamashita T, Abe F (2004) Residual stress within metallic model made by selective laser melting process. CIRP Ann Manuf Technol 53(1):195–198
Vora P, Mumtaz K, Todd I, Hopkinson N (2015) AlSi12 in-situ alloy formation and residual stress reduction using anchorless selective laser melting. Addit Manuf 7:12–19
Vrancken B et al (2015) Influence of preheating and oxygen content on selective laser melting of Ti6Al4V. In Proceedings of the 16th RAPDASA Conference. RAPDASA, Annual International Conference on Rapid Product Development Association of South Africa 4–6 November 2015. Pretoria, South Africa
Sha W, Malinov S (2009) Titanium alloys: modelling of microstructure, properties and applications. Elsevier
Homporova P et al (2011) Dynamic phase evolution in titanium alloy Ti-6Al-4V. in Proc. 12th World Conference on Titanium
Acknowledgements
The author would like to thank TWI and the EPSRC Future Manufacturing Hub in Manufacture using Advanced Powder Processes (MAPP)(EP/P006566/1) for their support during this investigation.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Ali, H., Ghadbeigi, H. & Mumtaz, K. Residual stress development in selective laser-melted Ti6Al4V: a parametric thermal modelling approach. Int J Adv Manuf Technol 97, 2621–2633 (2018). https://doi.org/10.1007/s00170-018-2104-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2104-9