Abstract
The paper studies the post-grinding temperature distribution on the inner ring of ball bearing 7008C. A grinding model was proposed to calculate the temperature distribution using the finite element method. The grinding process was simplified based on abrasive grain grinding motion. Our calculation takes account of the non-linear variation in physical properties of the bearing material as the temperature changes and the effects of convective heat transfer in the surrounding environment. A rectangular heat source and cyclic loading method were used to simulate the energy input during grinding, and the grinding temperature fields under different processing parameters were obtained. The calculated temperature fields are in good agreement with experimental results. The proposed model was then utilized to analyze the influence of different processing parameters on the temperature distribution, providing a basis for predicting the phase change and analyzing the post-grinding residual stress. Through processing parameter adjustments, the optimal parameter combinations that do not lead to material phase changes were identified. We hope this analysis will shed some light on the optimization of the bearing grinding process.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Liu SX, Lu YF (2001) Life test and failure analysis on site for super precision high speed spindle bearing. Bearing 6:36–37. https://doi.org/10.3969/j.issn.1000-3762.2001.06.019
Wang Y (2009) Failure of rolling bearing in industrial motors. Electric Mach Control Appl 36(9):38–43. https://doi.org/10.3969/j.issn.1673-6540.2009.09.010
Wang X, Yu T, Sun X, Shi Y, Wang WS (2016) Study of 3D grinding temperature field based on finite difference method: considering machining parameters and energy partition. Int J Adv Manuf Technol 84(5–8):1–13. https://doi.org/10.1007/s00170-015-7757-z
Li BK, Li CH, Zhang YB, Wang YG, Yang M, Jia DZ, Zhang NQ, Wu QD, Ding WF (2017) Numerical and experimental research on the grinding temperature of minimum quantity lubrication cooling of different workpiece materials using vegetable oil-based nanofluids. Int J Adv Manuf Technol 93(5–8):1971–1988. https://doi.org/10.1007/s00170-017-0643-0
Mamalis AG, Kundrák J, Manolakos DE, Gyani K, Markopoulos A, Horvath M (2003) Effect of the workpiece material on the heat affected zones during grinding: a numerical simulation. Int J Adv Manuf Technol 22(11–12):761–767. https://doi.org/10.1007/s00170-003-1685-z
Zhou L, Huang ST, Zhang CY (2013) Numerical and experimental studies on the temperature field in precision grinding of SiCp/Al composites. Int J Adv Manuf Technol 67(5–8):1007–1014. https://doi.org/10.1007/s00170-012-4543-z
Hu NS, Wang QY, Lin L, Tao Y (1992) Prediction of fatigue short crack growth rate in compressive residual stress field. J Xi'an Jiaotong Univ 3:93–98 (in Chinese)
He JW, Hu NS, Zhang DQ (1992) Effect of residual stress on high cycle fatigue performance. J Xi'an Jiaotong Univ 3:25–32 (in Chinese)
Choi Y, Liu CR (2006) Rolling contact fatigue life of finish hard machined surfaces: part 1 model development. Wear 261(5):485–491
Choi Y (2009) A study on the effects of machining-induced residual stress on rolling contact fatigue. Int J Fatigue 31(10):1517–1523
Zhou LQ, Li YP, Chen ZG (2009) Thermal deformation simulation for an internal grinding cirque by finite element method. Mod Mach 43(5–6):455
Jaeger JC (1942) Moving sources of heat and the temperature of sliding contacts. J Procroysoc NSW 76:203–224
Bei JY (1964) Analysis and study of grinding temperature. J Shanghai Jiaotong Univ 3:57–73 (in Chinese)
Rowe WB, Black SCE, Mills B, Morgan MN, Qi HS (1997) Grinding temperatures and energy partitioning. Proc Math Phys Eng Sci 453(1960):1083–1104
Rowe WB, Morgan MN, Black SCE, Mills B (1996) A simplified approach to control of thermal damage in grinding. CIRP Ann Manuf Technol 45(1):299–302
Rowe WB, Black SCE, Mills B (1996) Analysis of grinding temperatures by energy partitioning. Proc Inst Mech Eng B J Eng Manuf 210(62):579–588
Cai GQ, Zheng HW (1985) Some experimental studies on the grinding temperature of steel bille. J Northeast Univ Nat Sci 4:77–82 (in Chinese)
Zhao HH, Feng BF, Jin T, Cai GQ (2003) Three analytical heat models for high efficiency deep grinding. Diamond Abras Eng 2:18–20. https://doi.org/10.3969/j.issn.1006-852X.2003.02.005
Zhang L (2006) Theoretical analysis and experimental study on single plane grinding hardening technology. Dissertation, Shandong University (in Chinese)
Mao C (2008) Study of temperature field and thermal damage in plane grinding. Dissertation, Hunan University (in Chinese)
Wang DX (2015) Study on residual stress of roller bearing inner ring raceway grinding. Dissertation, Shandong University (in Chinese)
Salonitis K (2017) A hybrid cellular automata-finite element model for the simulation of the grind-hardening process. Int J Adv Manuf Technol 93(1):1–7. https://doi.org/10.1007/s00170-017-0829-5
Chen X, Rowe WB, Mccormack DF (2000) Analysis of the transitional temperature for tensile residual stress in grinding. J Mater Process Technol 107(1):216–221. https://doi.org/10.1016/S0924-0136(00)00692-0
Tong XF (2007) Finite element analysis and simulation of temperature field in grinding zone. Dissertation, Wuhan University of Technology (in Chinese)
Hahn RS (1962) On the nature of the grinding process. In: Proceeding of the 3rd International Machine Tool Design and Research Conference. pp 129–154
Shen NF, Zhang DJ, Li ZD (2003) New handbook of metallic materials. Science Publishing Company, China (in Chinese)
Rowe WB, Black SCE, Mills B, Qi HS, Morgan MN (1995) Experimental investigation of heat transfer in grinding. CIRP Ann Manuf Technol 44(1):329–332
Mao C, Zhou ZX, Ren YH, Zhang B (2010) Analysis and FEM simulation of temperature field in wet surface grinding. Adv Manuf Process 25(6):399–406. https://doi.org/10.1080/10426910903124811
Parente MPL, Vieira AA, Baptista AM (2012) Experimental and numerical study of the temperature field during creep feed grinding. Int J Adv Manuf Technol 61(1–4):127–134
Jin T, Stephenson DJ, Rowe WB (2003) Estimation of the convection heat transfer coefficient of coolant within the grinding zone. Proc Inst Mech Eng B J Eng Manuf 217(3):397–407
Jiang JL (2014) Study on surface topography and metamorphic layer of rolling bearing raceway grinding. Dissertation, Shandong University (in Chinese)
Anon (1980) Technological test for grinding surface deterioration layer of bearing ring. Bearing 03:38–46 (in Chinese)
Gui LF, Tang RJ, Xi BM, Bao WH (1984) Research on grinding steel metamorphic layer of bearing steel. J Mech Eng 20(1):39–50
Lu MJ (2004) Handbook of practical mechanical engineering materials. Liaoning Science and Technology Press, China (in Chinese)
Fergani O, Shao Y, Lazoglu I, Liang SY (2014) Temperature effects on grinding residual stress. Proc CIRP 14:2–6. https://doi.org/10.1016/j.procir.2014.03.100
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yu, G., Wang, Q., Song, Z. et al. Toward the temperature distribution on ball bearing inner rings during single-grit grinding. Int J Adv Manuf Technol 102, 957–968 (2019). https://doi.org/10.1007/s00170-018-03238-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-03238-0