Abstract
Since the microchannels have a vital role in microelectromechanical systems (MEMS), microfluidic and lab-on-a-chip devices, the surface quality, material removal rate (MRR), and geometrical accuracy of microchannels should be controlled well. The electrolyte nature is one of the dominant and important factors that affect the accuracy and performance of electrochemical discharge machining (ECDM). In this contribution, two alkaline electrolytes, NaOH and KOH, were mixed in equal proportion. It was observed that using NaOH + KOH mixed electrolyte at 15 and 25 wt% concentrations provides more electrical conductivity than KOH and NaOH separately at the same concentrations. It results in the fabrication of deeper microchannel with sharper sidewalls compared to KOH and NaOH, while its surface quality is preserved as well. Also, using 25, 30, and 35 wt% mixed electrolyte, due to higher viscosity compared to KOH, improved the surface quality of channels up to 35, 42, and 36%, respectively. Analyzing the waveform of the current response of various electrolytes showed that the microchannel with poor MRR and surface quality will be fabricated in the presence of salt electrolytes due to the generation of very low energy and unstable electrochemical sparks. In another part of the experiments, scanning electron microscopy (SEM) images and energy-dispersive X-ray (EDX) analysis of the tungsten carbide (WC) tool used in different electrolytes showed that the tools used in NaOH and NaNO3 had more severe wear compared to KOH and mixed electrolyte. Also, at the applied voltages of 50 V, the tool erosion was more serious compared to tool erosion at 35 V.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Wüthrich R, Hof L, Lal A, Fujisaki K, Bleuler H, Mandin P, Picard G (2005) Physical principles and miniaturization of spark assisted chemical engraving (SACE). J Micromech Microeng 15(10):S268
Liu J, Yue T, Guo Z (2010) An analysis of the discharge mechanism in electrochemical discharge machining of particulate reinforced metal matrix composites. Int J Mach Tools Manuf 50(1):86–96
Kurafuji H (1968) Electrical discharge drilling of glass I. Ann CIRP 16:415–419
Esashi M, Matsumoto Y, Shoji S (1990) Absolute pressure sensors by air-tight electrical feedthrough structure. Sensors Actuators A Phys 23(1–3):1048–1052
Basak I, Ghosh A (1997) Mechanism of material removal in electrochemical discharge machining: a theoretical model and experimental verification. J Mater Process Technol 71(3):350–359
Jain V, Dixit P, Pandey P (1999) On the analysis of the electrochemical spark machining process. Int J Mach Tools Manuf 39(1):165–186
Yang C, Ho S, Yan BH (2001) Micro hole machining of borosilicate glass through electrochemical discharge machining (ECDM). In: Key Engineering Materials. Trans Tech Publ, pp 149–166
Fascio V, Wüthrich R, Bleuler H (2004) Spark assisted chemical engraving in the light of electrochemistry. Electrochim Acta 49(22):3997–4003
Wüthrich R, Fascio V (2005) Machining of non-conducting materials using electrochemical discharge phenomenon—an overview. Int J Mach Tools Manuf 45(9):1095–1108
Wüthrich R, Spaelter U, Bleuler H (2006) The current signal in spark-assisted chemical engraving (SACE): what does it tell us? J Micromech Microeng 16(4):779
Didar TF, Dolatabadi A, Wüthrich R (2008) Characterization and modeling of 2D-glass micro-machining by spark-assisted chemical engraving (SACE) with constant velocity. J Micromech Microeng 18(6):065016
Cheng C-P, K-L W, Mai C-C, Yang C-K, Hsu Y-S, Yan B-H (2010) Study of gas film quality in electrochemical discharge machining. Int J Mach Tools Manuf 50(8):689–697
Ziki JDA, Didar TF, Wüthrich R (2012) Micro-texturing channel surfaces on glass with spark assisted chemical engraving. Int J Mach Tools Manuf 57:66–72
Zheng Z-P, Cheng W-H, Huang F-Y, Yan B-H (2007) 3D microstructuring of Pyrex glass using the electrochemical discharge machining process. J Micromech Microeng 17(5):960
Han M-S, Min B-K, Lee SJ (2007) Improvement of surface integrity of electro-chemical discharge machining process using powder-mixed electrolyte. J Mater Process Technol 191(1):224–227
Cheng C-P, K-L W, Mai C-C, Hsu Y-S, Yan B-H (2010) Magnetic field-assisted electrochemical discharge machining. J Micromech Microeng 20(7):075019
Han M-S, Min B-K, Lee SJ (2009) Geometric improvement of electrochemical discharge micro-drilling using an ultrasonic-vibrated electrolyte. J Micromech Microeng 19(6):065004
Salonitis K, Stournaras A, Stavropoulos P, Chryssolouris G (2009) Thermal modeling of the material removal rate and surface roughness for die-sinking EDM. Int J Adv Manuf Technol 40(3):316–323
Yang C-K, Cheng C-P, Mai C-C, Wang AC, Hung J-C, Yan B-H (2010) Effect of surface roughness of tool electrode materials in ECDM performance. Int J Mach Tools Manuf 50(12):1088–1096
Kim D-J, Ahn Y, Lee S-H, Kim Y-K (2006) Voltage pulse frequency and duty ratio effects in an electrochemical discharge microdrilling process of Pyrex glass. Int J Mach Tools Manuf 46(10):1064–1067
Ziki JDA, Wüthrich R (2012) Tool wear and tool thermal expansion during micro-machining by spark assisted chemical engraving. Int J Adv Manuf Technol 61(5–8):481–486
Behroozfar A, Razfar MR (2016) Experimental study of the tool wear during the electrochemical discharge machining. Mater Manuf Process 31(5):574–580
Wüthrich R, Hof L (2006) The gas film in spark assisted chemical engraving (SACE)—a key element for micro-machining applications. Int J Mach Tools Manuf 46(7):828–835
Bansal NP, Doremus RH (2013) Handbook of glass properties. Elsevier
Ribeiro AB, Mateus EP, Couto N Electrokinetics across disciplines and continents. Springer
Sivasankar B (2008) Engineering chemistry. Tata McGraw-Hill, New Delhi
Arthur D. Little I (1962) Electrical conductivity, compressibility, and viscosity of aqueous electrolytic solutions. Defense documentation center of scientific and technical information. Cameron station. Alexandra, Virginia
Allagui A (2011) On the electrochemical discharges for nanoparticles synthesis. (Doctoral dissertation, Concordia University)
Wüthrich R (2009) Micromachining using electrochemical discharge phenomenon: fundamentals and applications of spark assisted chemical engraving. William Andrew
Mousa M, Allagui A, Ng H, Wüthrich R (2008) The effect of thermal conductivity of the tool electrode in spark-assisted chemical engraving gravity-feed micro-drilling. J Micromech Microeng 19(1):015010
Goud M, Sharma AK, Jawalkar C (2016) A review on material removal mechanism in electrochemical discharge machining (ECDM) and possibilities to enhance the material removal rate. Precis Eng 45:1–17
Alexandrov AA (2005) The equations for thermophysical properties of aqueous solutions of sodium hydroxide. In: Nakahara M, Matubayasi N, Ueno M, Yasuoka K, Watanabe K (eds) Proceedings of the 14th international conference on the properties of water and steam, pp 86–90
Jiang B, Lan S, Ni J, Zhang Z (2014) Experimental investigation of spark generation in electrochemical discharge machining of non-conducting materials. J Mater Process Technol 214(4):892–898
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Sabahi, N., Razfar, M.R. Investigating the effect of mixed alkaline electrolyte (NaOH + KOH) on the improvement of machining efficiency in 2D electrochemical discharge machining (ECDM). Int J Adv Manuf Technol 95, 643–657 (2018). https://doi.org/10.1007/s00170-017-1210-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-1210-4