Abstract
Novel ultra-high-strength aluminum alloys provide enormous lightweighting potential for modern car body design. However, joining such alloys can be challenging. Refill friction stir spot welding is a solid-state joining process that provides fundamental advantages compared to conventional joining technologies when welding aluminum alloys. This work presents refill friction stir spot welding for joining 3-mm-thick Al-Mg-Si alloys. The welded joints have been optimized for shear load condition by the design of experiment and analysis of variance. The results show that it is possible to obtain welds of relatively thick Al-Mg-Si alloys with good mechanical properties. Microstructure analyses show that rotational speed and plunge depth play important roles in the bonded width and hook height, which affect the mechanical performance of the joint.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
T. Skszek, M. Zaluzec, J. Conklin, D. Wagner (2015) MMLV: project overview, SAE technical paper 2015–01-0407. doi: 10.4271/2015-01-0407.
C. A. Graf (2015) Automotive Circle Insight Edition @ Ford USA.
Schilling CDS, dos Santos JF (2004) Method and device for joining at least two adjoining work pieces by friction welding. GKSS Forschungszentrum Geesthacht Gmbh, United States Patent, US.
Amancio-Filho ST, Camillo APC, Bergmann L et al (2011) Preliminary investigation of the microstructure and mechanical behaviour of 2024 aluminium alloy friction spot welds. Mater Trans 52:985–991. doi:10.2320/matertrans.L-MZ201126
Shen Z, Yang X, Yang S, Zhang Z et al (2014) Microstructure and mechanical properties of friction spot welded 6061-T4 aluminum alloy. Mater Des 54(2014):766–778. doi:10.1016/j.matdes.2013.08.021
Rosendo T, Parra B, Tier MAD et al (2011) Mechanical and microstructural investigation of friction spot welded AA6181-T4 aluminium alloy. Mater Des 32:1094–1100. doi:10.1016/j.matdes.2010.11.017
Cao JY, Wang M, Kong L et al (2016) Hook formation and mechanical properties of friction spot welding in alloy 6061-T6. J Mater Process Technol 230:254–262. doi:10.1016/j.jmatprotec.2015.11.026
Zhao YQ, Liu HJ, Chen SX et al (2014) Effects of sleeve plunge depth on microstructures and mechanical properties of friction spot welded alclad 7B04-T74 aluminum alloy. Mater Des 62:40–46. doi:10.1016/j.jmatprotec.2015.11.026
Tier MD, Rosendo TS, dos Santos JF et al (2013) The influence of refill FSSW parameters on the microstructure and shear strength of 5042 aluminium welds. J Mater Process Technol 213:997–1005. doi:10.1016/j.jmatprotec.2012.12.009
Effertz PS, Infante V, Quintino L et al (2016) Fatigue life assessment of friction spot welded 7050-T76 aluminium alloy using Weibull distribution. Inter J Fatigue 87:381–390. doi:10.1016/j.ijfatigue.2016.02.030
Campanelli LC, Suhuddin UFH, dos Santos JF et al (2012) Preliminary investigation on friction spot welding of AZ31 magnesium alloy. Mater Sci Forum 706-709:3016–3021. doi:10.4028/www.scientific.net/MSF.706-709.3016
Plaine AH, Gonzalez AR, Suhuddin UFH et al (2015) The optimization of friction spot welding process parameters in AA6181-T4 and Ti6Al4V dissimilar joints. Mater Des 83:36–41. doi:10.1016/j.matdes.2015.05.082
Shen J, Suhuddin UFH, Cardillo MEB et al (2014) Eutectic structures in friction spot welding joint of aluminum alloy to copper. Appl Phys Lett 104:191901. doi:10.1063/1.4876238
Suhuddin U, Fischer V, Kroeff F et al (2014) Microstructure and mechanical properties of friction spot welds of dissimilar AA5754 Al and AZ31 Mg alloys. Mater Sci Eng A 590:384–389. doi:10.1016/j.msea.2013.10.057
Pieta G, dos Santos JF, Strohaecker TR et al (2014) Optimization of friction spot welding process parameters for AA2198-T8 sheets. Mater Manuf Process 29:934–940. doi:10.1080/10426914.2013.811727
Campanelli LC, Suhuddin UFH, Antonialli AÍS et al (2013) Metallurgy and mechanical performance of AZ31 magnesium alloy friction spot welds. J Mater Process Technol 213:515–521. doi:10.1016/j.jmatprotec.2012.11.002
Zhao Y, Liu H, Yang T et al (2016) Study of temperature and material flow during friction spot welding of 7B04-T74 aluminum alloy. Int J Adv Manuf Technol 83:1467–1475. doi:10.1007/s00170-015-7681-2
Plaine AH, Gonzalez AR, Suhuddin UFH et al (2016) Process parameter optimization in friction spot welding of AA5754 and Ti6Al4V dissimilar joints using response surface methodology. Int J Adv Manuf Technol 85:1575–1583. doi:10.1007/s00170-015-8055-5
Ji S, Wang Y, Zhang J et al (2017) Influence of rotating speed on microstructure and peel strength of friction spot welded 2024-T4 aluminum alloy. Int J Adv Manuf Technol 90:717–723. doi:10.1007/s00170-016-9398-2
Montgomery DC (2000) Design and analysis of experiments. Wiley, New York
Yin YH, Sun N, North TH et al (2010) Hook formation and mechanical properties in AZ31 friction stir spot welds. J Mater Process Technol 210:2062–2070. doi:10.1016/j.jmatprotec.2010.07.029
Author information
Authors and Affiliations
Corresponding author
Additional information
Highlights
• Friction spot welding of Al-Si-Mg alloy single-lap joints was demonstrated.
• The influence of joining parameters on joint mechanical performance was determined.
• A mathematical model for estimating lap shear strength was successfully established.
Rights and permissions
About this article
Cite this article
Santana, L.M., Suhuddin, U., Ölscher, M.H. et al. Process optimization and microstructure analysis in refill friction stir spot welding of 3-mm-thick Al-Mg-Si aluminum alloy. Int J Adv Manuf Technol 92, 4213–4220 (2017). https://doi.org/10.1007/s00170-017-0432-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0432-9