Abstract
Exposure Controlled Projection Lithography (ECPL) is a stereolithography-based additive manufacturing process, curing photopolymer parts on a stationary substrate. To improve the process accuracy with a closed-loop control, an in situ interferometric curing monitoring and measurement (ICM&M) system was developed to infer the output of cured height. The authors have previously reported an ICM&M method which consists of a sensor model for the ICM&M system and online parameter estimation algorithms based on instantaneous frequency. In this paper, to validate the ICM&M method, an application program was created in MATLAB to integrate the ECPL and ICM&M systems and to acquire and analyze interferograms online. Given the limited computing power, the ECPL process interferograms were acquired real time and analyzed off-line. A series of experiments was performed curing square samples by varying exposure time and intensity. Results show that the ICM&M can provide a cost-effective measurement for cured heights with excellent accuracy and reliability, and possess decent capability of estimating lateral dimensions. The off-line ICM&M is a convincing demonstration and benchmark for the real-time ICM&M metrology, providing a comprehensive evaluation of the ICM&M system’s measurement characteristics as well as its utilities in modeling and control of the additive manufacturing process dynamics.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Measurement Science Roadmap for Metal-Based Additive Manufacturing (2013) National Institute of Standards and Technology (NIST)
Farshidianfar M, Khajepour A, Gerlich A (2016) Real-time control of microstructure in laser additive manufacturing. Int J Adv Manuf Technol 82(5–8):1173–1186. doi:10.1007/s00170-015-7423-5
Bikas H, Stavropoulos P, Chryssolouris G (2015) Additive manufacturing methods and modelling approaches: a critical review. Int J Adv Manuf Technol 83(1–4):389–405. doi:10.1007/s00170-015-7576-2
Jariwala AS (2013) Modeling and process planning for exposure controlled projection lithography. Ph.D. Dissertation, Georgia Institute of Technology, Atlanta, USA
Zhao X, Rosen DW (2016) Simulation study on evolutionary cycle to cycle time control of exposure controlled projection lithography. Rapid Prototyp J 22(3):456–464
Jones HH, Jariwala AS, Rosen DW (2014) Towards real time control of exposure controlled projection lithography. Proceedings of International Symposium on Flexible Automation
Jones HH, Kwatra A, Jariwala AS, Rosen DW (2013) Real-time selective monitoring of exposure controlled projection lithography. Proceedings of the 24th Solid Freeform Fabrication Symposium:55–65
Jariwala AS, Schwerzel RE, Rosen DW (2011) Real-time interferometric monitoring system for exposure controlled projection lithography. Proceedings of the 22nd Solid Freeform Fabrication Symposium:99–108
Zhao X, Rosen DW (2015) Parameter estimation based real-time metrology for exposure controlled projection lithography. Proceedings of the 26th Annual International Solid Freeform Fabrication Symposium:1294–1312
Zhao X, Rosen DW (2016) Real-time interferometric monitoring and measuring of photopolymerization based stereolithographic additive manufacturing process: sensor model and algorithm. Meas Sci Technol 28(1). doi:10.1088/0957-0233/28/1/015001
The LEXT OLS4000 3D laser measuring microscope. http://www.olympus-ims.com/en/metrology/ols4000/. Accessed 09–10-2016
Colonna de Lega X (1997) Processing of non-stationary interference patterns—adapted phase-shifting algorithms and wavelet analysis. Application to dynamic deformation measurements by holographic and speckle interferometry. Swiss Federal Institute of Technology, Zürich, Switzerland
Tang Y (2005) Stereolithography cure process modeling. Georgia Institute of Technology, Atlanta
Arimoto H, Watanabe W, Masaki K, Fukuda T (2012) Measurement of refractive index change induced by dark reaction of photopolymer with digital holographic quantitative phase microscopy. Opt Commun 285(24):4911–4917
Lee JH, Prud’homme RK, Aksay IA (2001) Cure depth in photopolymerization: experiments and theory. J Mater Res 16(21):3536–3544
Jacobs PF (1992) Rapid prototyping and manufacturing: fundamentals of stereoLithography. Society of Manufacturing Engineers, Michigan, United States
Korpelainen V (2014) Traceability for nanometre scale measurements—atomic force microscopes in dimensional nanometrology. University of Helsinki, Finland
Hadis MA, Tomlins PH, Shortall AC, Palin WM (2010) Dynamic monitoring of refractive index change through photoactive resins. Dent Mater 26(11):1106–1112
Tomlins PH, Palin WM, Shortall AC, Wang RK (2007) Time-resolved simultaneous measurement of group index and physical thickness during photopolymerization of resin-based dental composite. J Biomed Opt 12(1):014020
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhao, X., Rosen, D.W. Experimental validation and characterization of a real-time metrology system for photopolymerization-based stereolithographic additive manufacturing process. Int J Adv Manuf Technol 91, 1255–1273 (2017). https://doi.org/10.1007/s00170-016-9844-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-9844-1