Abstract
Predictions for multi-index constrained forming limits and forming limits of Ti-alloy thin-walled tubes have become key problems urgently in need of solutions in order to improve forming potential in their shear bending processes under differential temperature fields. To address this, a method for predicting this type of forming limits was presented by coupling a thermal-mechanical-coupled finite element model for simulating these bending processes, with an energy model for the tubes’ shear-enforced plastic wrinkling predictions and utilizing the response surface designs. Reliable multi-index response surface models corresponding to the wrinkling, the thinning, and the flattening were developed for these TA2 Ti-alloy tubes’ shear bending processes, and their multi-index constrained forming limits were predicted. This found that forming limits, i.e., the maximum moving die displacements depend on the over-thinning or over-flattening for the present conditions. The smaller the values of the outer corner radius, the smaller both the feasible region ranges of the bending die cavity radius and/or the mandrel diameter and these forming limits. When the value of the outer corner radius is a half of the mandrel diameter and the values of the inner corner radius are from 4 to 6 mm; their feasible region ranges are the maximum. The effects of the feasible region of the bending die cavity radius on these forming limits are larger than the mandrel diameter. The moving die displacements located in the vertexes of their feasible regions are the maximum.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Yang H, Li H, Zhang ZY, Zhan M, Liu J, Li GJ (2012) Advances and trends on tube bending forming technologies. Chin J Aeronaut 25:1–12. doi:10.1016/S1000-9361(11)60356-7
Li H, Yang H, Liu K (2013) Towards an integrated robust and loop tooling design for tube bending. Int J Adv Manuf Technol 9–12:1303–1318. doi:10.1007/s00170-012-4258-1
Lazarescu L (2013) Effect of internal fluid pressure on quality of aluminum alloy tube in rotary draw bending. Int J Adv Manuf Technol 64:85–91. doi:10.1007/s00170-012-3992-8
Zhang ZY, Yang H, Li H, Tao ZJ (2014) Thermo-mechanical coupled 3D-FEmodeling of heat rotary draw bending for large diameter thin-walled CP-Ti tube. Int J Adv Manuf Technol 72:1187–1203. doi:10.1007/s00170-014-5709-7
Yan J, Yang H, Zhan M, Li H (2010) Forming characteristics of Al-alloy large diameter thin-walled tubes in NC-bending under axial compressive loads. Chin J Aeronaut 23:461–469. doi:10.1016/S1000-9361(09)60242-9
Zeng YS, Li ZQ (2002) Experimental research on the tube push-bending process. J Mater Proc Technol 122:237–240. doi:10.1016/S0924-0136(02)00027-4
Li SH, He J, Cedric Z, Zeng D, Hou B (2014) Bifurcation analysis of forming limits for an orthotropic sheet metal. J Manuf Sci Eng, Trans ASME 135:1–10. doi:10.1115/1.4027757
Li HZ, Wu X, Li GY (2013) Prediction of forming limit diagrams for 22MnB5 in hot stamping process. J Mater Eng Perform 22:2131–2140. doi:10.1007/s11665-013-0491-5
Hashemi R, Madoliat R, Afshar A (2014) Prediction of forming limit diagrams using the modified M-K method in hydroforming of aluminum tubes. Int J Mater Form. doi:10.1007/s12289-014-1207-6
Eyckens P, Bael AV, Houtte PV (2009) Marciniak–Kuczynski type modelling of the effect of through-thickness shear on the forming limits of sheet metal. Int J Plast 25:2249–2268. doi:10.1016/j.ijplas.2009.02.002
Butuca MC, Gracioa JJ, Barata RA (2006) An experimental and theoretical analysis on the application of stress-based forming limit criterion. Int J Mech Sci 48:414–429. doi:10.1016/j.ijmecsci.2005.11.007
Sun ZC, Yang H (2007) Study on forming limit and feasibility of tube axial compressive process. J Mater Proc Technol 187–188:292–295. doi:10.1016/j.jmatprotec.2006.11.102
Yang H, Lin Y (2004) Wrinkling analysis for forming limit of tube bending processes. J Mater Process Technol 152:363–369. doi:10.1016/j.jmatprotec.2004.04.410
Liu G, Peng JY, Yuan SJ, Teng BG, Li K (2015) Analysis on critical conditions of sidewall wrinkling for hydroforming of thin-walled Tee-joint. Int J Machin Tools Manuf 97:42–49. doi:10.1016/j.ijmachtools.2015.06.004
Bagheriasl R, Worswick MJ (2015) Formability of AA3003 brazing sheet at elevated temperatures: limiting dome height experiments and determination of forming limit diagrams. Int J Mater Form 8:229–244. doi:10.1007/s12289-014-1162-2
Yang LF, Hu GL, Liu JW (2015) Investigation of forming limit diagram for tube hydroforming considering effect of changing strain path. Int J Adv Manuf Technol 79:793–803. doi:10.1007/s00170-015-6842-7
Sun T, Liang J, Guo X, Ren MD, Wang LZ (2015) Optical measurement of forming limit and formability of Cu/Al clad metals. J Mater Eng Perform 24:1426–1433. doi:10.1007/s11665-015-1435-z
Narayanasamy R, Loganathan C (2006) Study on wrinkling limit of commercially pure aluminium sheet metals of different grades when drawn through conical and tractrix dies. Mater Sci Eng A 419:249–261. doi:10.1016/j.msea.2005.12.026
Li FF, Fu MW, Lin JP, Wang XN (2014) Experimental and theoretical study on the hot forming limit of 22MnB5 steel. Int J Adv Manuf Technol 71:297–306. doi:10.1007/s00170-013-5468-x
Chu XR, Leotoing L, Guines D, Ragneau E (2015) Effect of material thermo-viscoplastic modeling on the prediction of forming limit curves of aluminum alloy 5086. J Mater Eng Perform 24:3459–3470. doi:10.1007/s11665-015-1643-6
Xiao YH, Liu YL, Yang H (2014) Prediction of forming limit based on cross-sectional distortion for rotary draw bending of H96 brass double-ridged rectangular tube. Int J Adv Manuf Technol 71:1445–1454. doi:10.1007/s00170-013-5552-2
Nguyen DT, Kim YS (2013) A numerical study on establishing the forming limit curve and indicating the formability of complex shape in incremental sheet forming process. Int J Precis Eng Manuf 14:2087–2093. doi:10.1007/s12541-013-0283-8
Lee JW, Kwon HC, Rhee MH, Irn YT (2003) Determination of forming limit of a structural aluminum tube in rubber pad bending. J Mater Process Technol 140:487–493. doi:10.1016/S0924-0136(03)00775-1
Yan J, Yang H, Zhan M, Li H (2010) Forming limits under multi-index constraints in NC bending of aluminum alloy thin-walled tubes with large diameters. Sci China Tech Sci 53:326–342. doi:10.1007/s11431-009-0331-x
Sivasankaran S, Narayanasamy R, Jeyapaul R, Loganathan C (2009) Modelling of wrinkling in deep drawing of different grades of annealed commercially pure aluminium sheets when drawn through a conical die using artificial neural network. Mater Des 30:3193–3205. doi:10.1016/j.matdes.2009.01.020
Zemin F, Jianhua M, Chen L, Chen W (2010) Using genetic algorithm-back propagation neural network prediction and finite-element model simulation to optimize the process of multiple-step incremental air-bending forming of sheet metal. Mater Des 30:267–277. doi:10.1016/j.matdes.2009.06.019
Wei DL, Zhen ZS, Chen J (2009) Optimization and tolerance prediction of sheet metal forming process using response surface model. Comput Mater Sci 42:228–233. doi:10.1016/j.commatsci.2007.07.014
Yan J (2016) Plastic wrinkling model and characteristics of shear enforced titanium alloy thin-walled tubes under combination die constraints and differential temperature fields. Chin J Aeronaut doi:10.1016/j.cja. 2016.06.019
Editor commitee of “China aeronautical materials handbook” (2001) China aeronautical materials handbook. China standard press Beijing, pp 10–20 (in Chinese)
Yan J, Wu W (2016) Identification method of shear stress constitutive parameters of Ti-alloy thin-walled tube. Acta Aeronautica Et Astronautica Sinica 37:2884–2894. doi:10.7527/S1000-6893.2015.0289
Zhao ZN (2002) Heat transfer. Higher education press, Beijing (in Chinese)
Li YQ, Lin ZR, Chen CK, Zhang ZY, Ying JL (1986) Ti-alloy sheet metal forming technology. Defense Industry Press, Beijing (in Chinese)
Hibbit K, Sorensen (2009) ABAQUS. Version 6.9. Hibbit Karlson and Sorensen Inc Washington
Ren LQ (2009) Regression design and its optimization. Science Press, Beijing (in Chinese)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yan, J., Wu, W. & Xu, B. Prediction for multi-index constrained forming limit in shear bending process of Ti-alloy thin-walled tube under differential temperature fields. Int J Adv Manuf Technol 91, 1117–1128 (2017). https://doi.org/10.1007/s00170-016-9791-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-9791-x