Abstract
Fiber orientation in reinforced polymer parts can greatly affect the appearance and mechanical properties. The fiber orientation process during a confluent process of two or more strands of melt in a mold cavity is discussed. Different from common polymer melts with no reinforced material, a novel model describing the confluent process for fiber-reinforced melt is established. Through finite element simulation, fiber orientation and its accumulation state in different layers of plastic parts are obtained. 3D surface morphologies of the confluent region caused by fiber orientation and distribution are tested in the laboratory, and the relationships between the mold temperature and the appearance of the confluent region are presented as well. By using SEM to observe the fiber orientation induced in different mold temperatures, the effect of the fiber orientation in confluent region process on the impact strength of the resultant parts is discussed. Testing results prove that the established model is effective in explaining the outcome of the confluent process for fiber-reinforced materials.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Bay RS (1991) Fiber orientation in injection-molded composites: A comparison of theory and experiment. University of Illinois at Urbana-Champaign
Vincent M, Giroud T, Clarke A, Eberhardt C (2005) Description and modeling of fiber orientation in injection molding of fiber reinforced thermoplastics. Polymer 46(17):6719–6725
Li XP, Zhao GQ, Yang C (2014) Effect of mold temperature on motion behavior of short glass fibers in injection molding process. Int J Adv Manuf Technol 73(5–8):639–645
Wang J, Nguyen BN, Mathur R, Sharma B, Sangid MD, Costa F, Fifield LS (2015) Fiber orientation in injection molded long carbon fiber thermoplastic composites. Composites 6:8
Wang G, Zhao G, Wang X (2013) Experimental research on the effects of cavity surface temperature on surface appearance properties of the moulded part in rapid heat cycle moulding process. Int J Adv Manuf Technol 68(5–8):1293–1310
Kovács JG, Sikló B (2010) Experimental validation of simulated weld line formation in injection moulded parts. Polymer Test 29:910–914
Park K, Sohn DH, Cho KH (2010) Eliminating weldlines of an injection-molded part with the aid of high-frequency induction heating. J Mech Sci Tech 24:149–152
Chen SC, Jong WR, Chang JA (2006) Dynamic mold surface temperature control using induction heating and its effects on the surface appearance of weld line. J Appl Polym Sci 101:1174–1180
Chen CS, Chen TJ, Chien RD, Chen SC (2007) Investigation on the weldline strength of thin-wall injection molded abs parts. Int Commun Heat Mass Transfer 34:448–455
Kuo HC, Jeng MC (2010) Effects of part geometry and injection molding conditions on the tensile properties of ultra-high molecular weight polyethylene polymer. Mater Des 31:884–893
Tham NC (2004) Flow analysis of the weld line formation during injection mould filling of thermoplastics. Rheol Acta 43(3):240–245
Ozcelik B, Kuram E, Topal MM (2012) Investigation the effects of obstacle geometries and injection molding parameters on weld line strength using experimental and finite element methods in plastic injection molding. Int Comm Heat Mass Tran 39(2):275–281
Xie L, Zhu D, Ziegmann G, Steuernagel L (2016) Investigation on correlation between cold/hot weld line mechanical properties and micro injection molding processing parameters. une, 13: 15
Kagitci YC, Tarakcioglu N (2015) The effect of weld line on tensile strength in a polymer composite part. Int J Adv Manuf Technol:1–11
Selden R (1997) Effect of processing on weld line strength in five thermoplastics. Polym Eng Sci 37:205–218
Wang G, Zhao G, Wang X (2013) Effects of cavity surface temperature on reinforced plastic part surface appearance in rapid heat cycle moulding. Mater Des 44:509–520
Wang G, Zhao G, Wang X (2013) Effects of cavity surface temperature on mechanical properties of specimens with and without a weld line in rapid heat cycle molding. Mater Des 46:457–472
Kalus J, Jørgensen JK (2014) Measuring deformation and mechanical properties of weld lines in short fibre reinforced thermoplastics using digital image correlation. Polymer Test 36:44–53
Tzeng CJ, Yang YK, Lin YH, Tsai CH (2012) A study of optimization of injection molding process parameters for SGF and PTFE reinforced PC composites using neural network and response surface methodology. Int J Adv Manuf Technol 63(5–8):691–704
Karsli NG, Aytac A (2013) Tensile and thermomechanical properties of short carbon fiber reinforced polyamide 6 composites. Compos B Eng 51:270–275
Wang W, Zhao G, Guan Y, Wu X, Hui Y (2015) Effect of rapid heating cycle injection mold temperature on crystal structures, morphology of polypropylene and surface quality of plastic parts. J Polymer Res 22(5):1–11
Inoue A, Morita K, Tanaka T, Arao Y, Sawada Y (2015) Effect of screw design on fiber breakage and dispersion in injection-molded long glass-fiber-reinforced polypropylene. J Compos Mater 49(1):75–84
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Li, X., Gong, N., Gao, Z. et al. Fiber orientation in melt confluent process for reinforced injection molded part. Int J Adv Manuf Technol 90, 1457–1463 (2017). https://doi.org/10.1007/s00170-016-9333-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-9333-6