Abstract
Four tools with taper (TA), triangular (TB), three-grooves (TC), and square (TD) pin-tip profiles were designed to friction stir weld (FSW) thick AA7075-T6 alloy plates aiming at improving the local and overall mechanical properties of the joints. The microstructure evolution, hardness, and mechanical properties of the FSW joints were studied by scanning election microscope (SEM), X-ray diffractometer (XRD), and transmission electron microscope (TEM). The results show that equiaxed grains in the bottom nugget zone (BNZ) obtained by using TC are noticeably refined compared to in the case of other tools. Also, finer and more dispersive precipitates are distributed in this BNZ, and higher contents of η phase and dislocations are observed. A similar trend is found in the middle of weld. The bottom slices welded by employing TC show superior strength and ductility with a highest ultimate tensile strength of 388 MPa, yield strength of 315 MPa, and elongation of 7.9 %, which are in agreement with the hardness profiles. This is owing to ultrafine grains, more high-angle grain boundaries, more dispersive and higher contents of precipitates, and optimum hardness distribution. Accordingly, the global mechanical properties of the overall joints prepared by using TC significantly improve.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Sharma C, Dwivedi DK, Kumar P (2013) Effect of post weld heat treatments on microstructure and mechanical properties of friction stir welded joints of Al-Zn-Mg alloy AA7039. Mater Des 43:134–143
Su JQ, Nelson TW, Mishra R, Mahoney M (2003) Microstructural investigation of friction stir welded 7050-T651 aluminium. Acta Mater 51:713–729
Bahemmat P, Haghpanahi M, BesharatiGivi M, Reshad Seighalani K (2012) Study on dissimilar friction stir butt welding of AA7075-O and AA2024-t4 considering the manufacturing limitation. Int J Adv Manuf Technol 59(9–12):939–953
Fu RD, Sun ZQ, Sun RC, Li Y, Liu HJ, Liu L (2011) Improvement of weld temperature distribution and mechanical properties of 7050 aluminum alloy butt joints by submerged friction stir welding. Mater Des 32:4825–4831
Fuller CB, Mahoney MW, Calabrese M, Micona L (2010) Evolution of microstructure and mechanical properties in naturally aged 7050 And 7075 Al friction stir welds. Mater Sci Eng A 527:2233–2240
Balasubramanian V, Ravisankar V, Madhusudhan RG (2008) Effect of postweld aging treatment on fatigue behavior of pulsed current welded AA7075 aluminum alloy joints. J Mater Eng Perform 7:224–233
Feng AH, Chen DL, Ma ZY (2010) Microstructure and cyclic deformation behavior of a friction-stir- welded 7075 Al alloy. Metall Mater Trans A 41:957–971
Singh R, Sharma C, Dwivedi D, Mehta N, Kumar P (2011) The microstructure and mechanical properties of friction stir welded Al–Zn–Mg alloy in as welded and heat treated conditions. Mater Des 32(2):682–687
Sivaraj P, Kanagarajan D, Balasubramanian V (2014) Effect of post-weld heat treatment on tensile properties and microstructure characteristics of friction stir welded armour grade AA7075-T651 aluminium alloy. Def Technol Bus 10(1):1–8
Mao YQ, Ke LM, Liu FC, Huang CP, Chen YH, Liu Q (2015) Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of 2060 aluminum lithium alloy. Int J Adv Manuf Technol 81(5):1419–1431
Mironov S, Masaki K, Sato YS, Kokawa H (2012) Relation between material flow and abnormal grain growth in friction-stir welds. Scr Mater 67:983–986
Krishnan KN (2002) On the formation of onion rings in friction stir welds. Mater Sci Eng A 327:246–251
Scialpi A, De Filippis LAC, Cavaliere P (2007) Influence of shoulder geometry on microstructure and mechanical properties of friction stir welded 6082 aluminum alloy. Mater Des 28:1124–1129
Fujii H, Cui L, Maeda M, Nogi K (2006) Effect of tool shape on mechanical properties and microstructure of friction stir welded aluminum alloys. Mater Sci Eng A 419:25–31
Zhou CZ, Yang XQ (2006) Effect of kissing bond on fatigue behavior of friction stir welds on Al 5083 alloy. J Mater Sci 41:2771–2777
Paglia CS, Buchheit RG (2008) A look in the corrosion of aluminum alloy friction stir welds. Scr Mater 58:383–387
Avettand Fenoel M, Taillard R (2015) Heterogeneity of the nugget microstructure in a thick 2050 Al friction-stirred weld. Metall Mater Trans A 46A:300–314
Canaday Clinton T, Moore Matthew A, Tang W, Reynolds AP (2013) Through thickness property variations in a thick plate AA7050 friction stir welded joint. Mater Sci Eng A 559:678–682
Srinivasa Rao T, Madhusudhan Reddy G, Koteswara Rao SR (2015) Microstructure and mechanical properties of friction stir welded AA7075T651 aluminum alloy thick plates. Trans Nonferrous Metals Soc China 25:1770–1778
Xu WF, Liu JH, Luan GH, Dong CL (2009) Temperature evolution, microstructure and mechanical properties of friction stir welded thick 2219-O aluminum alloy joints. Mater Des 30:1886–1893
Mishra RS, Ma ZY (2005) Friction stir welding and processing. Mater Sci Eng R 50:1–78
Nandan R, Deb Roy T, Bhadeshia HKDH (2008) Recent advances in friction stir welding-process, weldment structure and properties. Prog Mater Sci 53:980–1023
Liu H, Chen Y, Feng J (2006) Effect of zigzag line on the mechanical properties of friction stir welded joints of an Al-Cu alloy. Scr Mater 55:231–234
Thomas WM, Nicolash ED, Smith SD (2001) Friction stir welding-Tool developments. In: Das SK, Kaufman JG, Lienert TJ, editors. Aluminium 2001 proceedings of the TMS 2001 aluminum automotive and joining session, TMS; 213–224.
Zhang YN, Cao X, Larose S, Wanjara P (2012) Review of tools for friction stir welding and processing. Can Metall Q 51(3):250–261
Thomas WM, Nicholas ED (1997) Friction stir welding for the transportation industries. Mater Des 18:269–273
Elangovan K, Balasubramanian V (2008) Influences of tool pin profile and tool shoulder diameter on the formation of friction stir processing zone in AA6061 aluminum alloy. Mater Des 29:362–373
Dawood HI, Mohammed KS, Rahmat A, Uday MB (2015) Effect of small tool pin profiles on microstructures and mechanical properties of 6061 aluminum alloy by friction stir welding. Trans Nonferrous Metals Soc China 25:2856–2865
Khodaverdizadeh H, Heidarzadeh A, Saeid T (2013) Effect of tool pin profile on microstructure and mechanical properties of friction stir welded pure copper joints. Mater Des 45:265–270
Heidarzadeh A, Kazemi-Choobi K, Hanifian H, Asadi P (2014) Microstructural evolution. In: Givi MKB, Asadi P (eds) Advances in friction-stir welding and processing. Woodhead Publishing, Cambridge, pp 65–140. doi:10.1533/9780857094551.65
Mao YQ, Ke LM, Liu FC, Liu Q, Huang CP, Xing L (2014) Effect of tool pin eccentricity on microstructure and mechanical properties in friction stir welded 7075 aluminum alloy thick plate. Mater Des 62:334–343
McNelley TR, Swaminathan S, Su JQ (2008) Recrystallization mechanisms during friction stir welding/processing of aluminum alloys. Scr Mater 58(5):349–354
Zhao YH, Zhu YT, Lavernia EJ (2010) Preparation of nanostructured materials having improved ductility. Adv Eng Mater 12:769–788
Chinh NQ, Szommer P, Horita Z, Langdon TG (2006) Experimental evidence for grain-boundary sliding in ultrafine-grained aluminum processed by severe plastic deformation. Adv Mater 18:34–39
Mao YQ, Ke LM, Liu FC, Chen YH, Xing L (2015) Investigations on temperature distribution, microstructure evolution and property variations along thickness in friction stir welded joints for thick AA7075-T6 plates. Int J Adv Manuf Technol. doi:10.1007/s00170-015-8182-z
Feng ZQ, Yang YQ, Huang B, Han M, Luo X, Ru JG (2010) Precipitation process along dislocations in Al–Cu–Mg alloy during artificial aging. Mater Sci Eng A 528:706–714
Feng AH, Chen DL, Ma ZY (2010) Microstructure and low-cycle fatigue of a friction-stir-welded 6061 aluminum alloy. Metall Mater Trans A 41:2626–2641
Mironov S, Masaki K, Sato YS, Kokawa H (2012) Relationship between material flow and abnormal grain growth in friction-stir welds. Scr Mater 67(12):983–986
Starink MJ, Deschamps A, Wang SC (2008) The strength of friction stir welded and friction stir processed aluminium alloys. Scr Mater 58:377–382
Hu ZL, Wang XS, Yuan SJ (2012) Quantitative investigation of the tensile plastic deformation characteristic and microstructure for friction stir welded 2024 aluminum alloy. Mater Charact 73:114–123
Sato YS, Urata M, Kokawa H, Ikeda K (2003) Hall–Petch relationship in friction stir welds of equal channel angular-pressed aluminium alloys. Mater Sci Eng A 354:298–305
Sharma C, Dwivedi DK, Kumar P (2013) Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of AA7039 aluminum alloy. Mater Des 36:379–390
Mahoney MW, Rhodes CG, Flintoff JG, Spurling RA, Bingel WH (1998) Properties of friction stir welded 7075 T651 aluminum. Metall Mater Trans A 29A:1955–1964
Nielsen KL, Pardoen T, Tvergaard V, de Meester B, Simar A (2010) Modelling of plastic flow localisation and damage development in friction stir welded 6005A aluminium alloy using physics based strain hardening law. Int J Solids Struct 47(18–19):2359–2370
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Mao, Y., Ke, L., Chen, Y. et al. Improving local and global mechanical properties of friction stir welded thick AA7075-T6 joints by optimizing pin-tip profile. Int J Adv Manuf Technol 88, 1863–1875 (2017). https://doi.org/10.1007/s00170-016-8886-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-8886-8