Abstract
Selective laser melting (SLM) process, an additive manufacturing (AM) technology, has had a rapid growth in the biomedical and aerospace markets because of the ability to manufacture complex designs directly from computer-aided design (CAD) using materials such as titanium and aluminum alloys. Although this technology allows designers to fabricate geometries not achievable with conventional manufacturing, it has some restrictions. The paper presents the technological problems and restrictions resulting in the production of structures in aluminum alloy by SLM. In particular, it analyzed the input file of the process, .STL file, and the dimensional limits of geometries with sharp edges as a simple parallelepiped with a square base since the understanding of the limitations can help the designer in the creation of new components. The creation of function-independent design rules, easily transferrable on individual part designs, could allow a wide industrial usage and a better knowledge of AM technologies. The results presented in this paper showed that the choice of parameters of conversion from the CAD model to .STL file could be a restriction for the software for preprocessing part but also affects the surface roughness. Moreover, if a SLM machine with a laser beam of 100 μm is used, it is not possible to produce geometries with sharp edges with size base below 0.8 mm in an aluminum alloy.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Byun HS, Lee K (2003) Design of a new test part for benchmarking the accuracy and surface finish of rapid prototyping processes, Computational science and its applications ICCSA 2003, In: V. Kumar, M. Gavrilova, C. Tan, and P. L’Ecuyer (eds), Springer Berlin / Heidelberg, 989–989
Kruth JP (1991) Material incress manufacturing by rapid prototyping techniques. CIRP Ann Manuf Technol 40(2):603–614. doi:10.1016/s00078506(07)61136-6
Childs THC, Juster NP (1994) Linear and geometric accuracies from layer manufacturing. CIRP Ann Manuf Technol 43(1):163–166. doi:10.1016/s0007-8506(07)62187-8
Jayaram D, Bagchi A, Jara-Almonte CC, O’Reilly S (1994) Benchmarking of rapid prototyping systems—beginning to set standards, Proceedings of the Solid Freeform Fabrication Symposium, 146–153
Xu F, Wong YS, Loh HT (2000) Toward generic models for comparative evaluation and process selection in rapid prototyping and manufacturing. J Manuf Syst 19(5):283–296
Campbell RI, Martorelli M, Lee HS (2002) Surface roughness visualization for rapid prototyping models. Comput Aided Des 34:717–725
Grimm T (2003) Rapid prototyping benchmark: 3D printers
Mahesh M, Wong Y, Fuh JYH, Loh HT (2004) Benchmarking for comparative evaluation of RP systems and processes. Rapid Prototyp J 10(2):123–135. doi:10.1108/13552540410526999
Kim GD, Oh YT (2008) A benchmark study on rapid prototyping processes and machines: quantitative comparisons of mechanical properties, accuracy, roughness, speed, and material cost. Proc Inst Mech Eng B J Eng Manuf 222(2):201–215. doi:10.1243/09544054JEM724
Brajlih T, Valentan B, Balic J, Drstvensek I (2011) Speed and accuracy evaluation of additive manufacturing machines. Rapid Prototyp J 17(1):64–75. doi:10.1108/13552541111098644
Richter J, Jacobs P (1992) Accuracy. In: Jacobs P. (ed) Rapid prototyping & manufacturing, Society of Manufacturing Engineers, 287–315
Moylan S, Slotwinski J, Cooke A, Jurrens K, Donmez MA (2014) An additive manufacturing test artifact. J Res Natl Inst Stand Technol 119:429–459
Kruth JP, Vandenbroucke B, Vaerenbergh JV, Mercelis P (2005) Benchmarking of different SLS/SLM processes as rapid manufacturing techniques. Int. Conf. Polymers & Moulds Innovations (PMI), Gent
Scaravetti D, Dubois P, Duchamp R (2008) Qualification of rapid prototyping tools: proposition of a procedure and a test part. Int J Adv Manuf Technol 38(7):683–690. doi:10.1007/s00170-007-1129-2
Daniel T (2009) The development of design rules for selective laser melting. PhD Thesis
Adam GAO, Zimmer D (2014) Design for additive manufacturing-element transitions and aggregated structures. CIRP J Manuf Sci Technol 7:20–28
Kranz J, Herzog D, Emmelmann C (2015) Design guidelines for laser additive manufacturing of lightweight structures in TiAl6V4. J Laser Appl 27:S14001
Wohlers T (2013) Additive manufacturing and 3D printing state of the industry: Wohlers report. Wohlers Associates Inc., Fort Collins
Calignano F (2014) Design optimization of supports for overhanging structures in aluminum and titanium alloys by selective laser melting. Mater Des 64:2013–2213
Calignano F, Manfredi D, Ambrosio EP, Iuliano L, Fino P (2013) Influence of process parameters on surface roughness of aluminum parts produced by DMLS. Int J Adv Manuf Technol 67:2743–2751
Ventola L, Robotti F, Dialameh M, Calignano F, Manfredi D, Chiavazzo E, Asinari P (2014) Rough surfaces with enhanced heat transfer for electronics cooling by direct metal laser sintering. Int J Heat Mass Transf 75:58–74
Song YA, Koenig W (1997) Experimental study of the basic process mechanism for direct selective laser sintering of low-melting metallic powder. CIRP Ann-Manuf Techn 46(1):127–130
Das S, Beaman JJ, Wohlert M, Bourell DL (1998) Direct laser freeform fabrication of high performance metal components. Rapid Prototyp J 4(3):112–117
Simchi A (2006) Direct laser sintering of metal powders: mechanism, kinetics and microstructural features. Mater Sci Eng A 428(1–2):148–158
Agarwala M, Bourell D, Beaman J, Marcus H, Barlow J (1995) Direct selective laser sintering of metals. Rapid Prototyp J 1(1):26–36
Wang XC, Laoui T, Bonse J, Kruth JP, Lauwers B, Froyen L (2002) Direct selective laser sintering of hard metal powders: experimental study and simulation. Int J Adv Manuf Technol 19(5):351–357
Manfredi D, Calignano F, Krishnan M, Canali R, Ambrosio EP, Atzeni E (2013) From powders to dense metal parts: characterization of a commercial AlSiMg alloy processed through direct metal laser sintering. Materials 6:856–869
Ning Y, Wong YS, Fuh JYH, Loh HT (2006) An approach to minimize build errors in direct metal laser sintering. IEEE Trans Autom Sci Eng 3(1):73–80
Ning Y, Wong YS, Fuh JYH (2005) Effect and control of hatch length on material properties in the direct metal laser sintering process. Proc Inst Mech Eng B J Eng Manuf 219(1):15–25
Zhao ZW, Laperriere L (2000) Adaptive direct slicing of the solid model for rapid prototyping. Int J Prod Res 38(1):69–83
Zhao J, Xia R, Liu W, Wang H (2009) A computing method for accurate slice contours based on an STL model. Virtual Phys Prototyping 4(1):29–37
Zhou MY, Xi JT, Yan JQ (2004) Adaptive direct slicing with non-uniform cusp heights for rapid prototyping. Int J Adv Manuf Technol 23(1–2):20–27
Jamieson R, Hacker H (1995) Direct slicing of CAD models for rapid prototyping. Rapid Prototyp J 1(2):4–12
Pandey PM, Reddy NV, Dhande SG (2003) Slicing procedures in layered manufacturing: a review. Rapid Prototyp J 9(5):274–288
Choi SH, Samavedam S (2002) Modelling and optimisation of rapid prototyping. Comput Ind 47(1):39–53
Masood SH, Rattanawong W (2002) A generic part orientation system based on volumetric error in rapid prototyping. Int J Adv Manuf Technol 19(3):209–216
Rattanawong W, Masood SH, Iovenitti P (2001) A volumetric approach to part-build orientations in rapid prototyping. J Mater Process Technol 119(1–3):348–353
Paul R, Anand S (2011) Optimal part orientation in rapid manufacturing process for achieving geometric tolerances. J Manuf Syst 30(4):214–222
Ollison T, Berisso K (2010) Three-dimensional printing build variables that impact cylindricity. J Ind Technol 26(1):1–10
Arni R, Gupta SK (2001) Manufacturability analysis of flatness tolerances in solid freeform fabrication. J Mech Des 123(1):148–156
Lynn-Charney C, Rosen DW (2000) Usage of accuracy models in stereolithography process planning. Rapid Prototyp J 6(2):77–86
Nagahanumaiah SK, Ravi B (2008) Computer aided rapid tooling process selection and manufacturability evaluation for injection mold development. Comput Ind 59(2–3):262–276
Evans AG, Hutchinson JW, Fleck NA, Ashby MF, Wadley HNG (2001) The topological design of multifunctional cellular metals. Prog Mater Sci 46:309–327
Wadley HNG, Fleck NA, Evans AG (2003) Fabrication and structural performance of periodic cellular metal sandwich structures. Comput Sci Technol 63:2331–2343
Gibson LJ, Ashby MF (1997) Cellular solids. Structure and properties. Cambridge University Press, Cambridge
Wong M, Tsopanos S, Sutcliffe CJ, Owen I (2007) Selective laser melting of heat transfer devices. Rapid Prototyp J 13(5):291–297
Tsopanos S, Sutcliffe CJ, Owen I (2005) The manufacture of micro cross-flow heat exchangers by selective laser melting. Proceedings of ECI: Fifth International Conference on Enhanced, Compact and Ultra Compact Heat Exchangers, 410–417
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Calignano, F., Lorusso, M., Pakkanen, J. et al. Investigation of accuracy and dimensional limits of part produced in aluminum alloy by selective laser melting. Int J Adv Manuf Technol 88, 451–458 (2017). https://doi.org/10.1007/s00170-016-8788-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-8788-9