Abstract
Machining of metal matrix composite is a big challenge in industry for the high cutting tool cost and limited machining efficiency. In this study, blasting erosion arc machining (BEAM) was applied to improve the machining efficiency of SiC/Al composite. The performance of BEAM under negative and positive electrode machining conditions was investigated, and two sets of 3-factor, 2-level full factorial experiments were conducted to disclose the effects between the machining parameters. When the peak current was 500 A and the tool polarity was negative, the obtained MRR (material removal rate) was greater than 8270 mm3/min, and the TWR (tool wear ratio) was about 2 %. The competitive efficiency and economy of BEAM indicate the potential of electrical arcing in handling difficult-to-cut composite materials. The optimization of machining conditions can result in a high MRR which arrived to 10, 200 mm3/min, and the specific MRR was nearly three times of that of EDM. Furthermore, it was disclosed that the MRR in both negative and positive machining was sensitive to the peak current, pulse duration, and pulse interval while the TWR was appeared to be stable as the machining conditions varies within a certain range. The surface topography of the machined workpiece indicates that compared to the negative BEAM, positive BEAM creates a smoother surface under the same machining conditions. Furthermore, in order to study the influence of SiC particles on the machining performance, a complementary experiment was conducted to compare the craters formed on 20 vol.% SiC/Al and pure aluminum. Based on the comparison results, it can be deduced that the discharging condition is possibly influenced by the SiC particles and result in smaller craters. Finally, a workpiece was machined to demonstrate the advantages of BEAM for the machining of SiC/Al composites.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Song M (2009) Effects of volume fraction of SiC particles on mechanical properties of SiC/Al composites. Trans Nonferrous Metals Soc China 19:1400–1404. doi:10.1016/S1003-6326(09)60040-6
Karthikeyan R, Ganesan G, Nagarazan RS, Pai BC (2001) A critical study on machining of Al/SiC composites. Materials Manuf Process 16(1):47–60. doi:10.1081/AMP-100103696
Radhakrishnan R, Muthukrishnan N, Raju R (2011) Optimization of cutting parameters for turning Al-SiC(10p) MMC using ANOVA and grey relational analysis. Int J Precis Eng Manuf 12(4):651–656. doi:10.1007/s12541-011-0084-x
Mohana B, Rajadurai A, Satyanarayana KG (2004) Electric discharge machining of Al–SiC metal matrix composites using rotary tube electrode. J Mater Process Technol 153–154:978–985. doi:10.1016/j.jmatprotec.2004.04.347
Seo YW, Kim D, Ramulu M (2006) Electrical discharge machining of functionally graded 15–35Vol% SiC/Al composites. Mater Manuf Process 21:479–487. doi:10.1080/10426910500471482
Trimmer AL, Hayashi S, Lamphere M (2010) Advancement in high speed electro-erosion processes for machining tough metals. Proeeedings of the 16th International Sympo-sium on Electromachining. Shanghai
Ye J, Wu G, Wang F, Wu Q, Xu L, Luo G (2011) The orthogonal test and reach on the optimum parameters of the pulse power in NC high performance electrical-discharge milling. Electromachining Mould 2011(6):16–20
Wang F, Liu Y, Shen Y et al (2013) Machining performance of Inconel 718 using high current density electrical discharge milling. Mater Manuf Process 28:1147–1152. doi:10.1080/10426914.2013.822985
Zhao W, Gu L, Xu H et al (2013) A novel high efficiency electrical erosion process—blasting erosion arc machining. Procedia CIRP 6:621–625. doi:10.1016/j.procir.2013.03.057
Yuan R, Wei B, Luo Y et al (2010) High-speed electroerosion milling of superalloys. ISEM-16, Shanghai: 207–210
Wang F, Liu Y, Tang Z, Ji R, Zhang Y, Shen Y (2014) Ultra-high speed combined machining of electrical discharge machining and arc machining. Proc Inst Mech Eng B J Eng Manuf 228(5):663–672. doi:10.1177/0954405413506194
Wang F, Liu Y, Zhang Y (2014) Compound machining of titanium alloy by super high speed EDM milling and arc machining. J Mater Process Technol 214:531–538. doi:10.1016/j.jmatprotec.2013.10.015
Chengbo G, Shichun D, Dongbo W, Yunlong S, Xiang W (2015) Research on efficient electrical discharge milling of TC4 titanium alloy. Acta Armamentarii 36(11):2149–2156. doi:10.3969/j.issn.1000-1093.2015.11.020
Xu H, Gu L, Chen J et al (2015) Machining characteristics of nickel-based alloy with positive polarity blasting erosion arc machining. Int J Adv Manuf Technol 79(5–8):937–947. doi:10.1007/s00170-015-6891-y
Chen J, Gu L, Xu H, et al (2015) Study on blasting erosion arc machining of Ti–6Al–4V alloy[J]. Int J Adv Manuf Technol:1–11. doi:10.1007/s00170-015-8126-7
Xia H, Hashimoto H, Kunieda M et al (1996) Measurement of energy distribution in continuous EDM process. J JSPE 62(8):1141–1145. doi:10.2493/jjspe.62.1141
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Gu, L., Chen, J., Xu, H. et al. Blasting erosion arc machining of 20 vol.% SiC/Al metal matrix composites. Int J Adv Manuf Technol 87, 2775–2784 (2016). https://doi.org/10.1007/s00170-016-8676-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-8676-3