Abstract
Variable polarity plasma arc-gas metal arc welding (VPPA-GMAW) is a superior technology for welding thick plates of high-strength aluminum alloys. It integrates the advantages of energy focusing and high penetration depth in VPPA welding, and those of high welding efficiency and wide range of technological parameters in GMAW process. In this work, we investigated the droplet momentum in paraxial VPPA-GMAW hybrid welding of 7A52 aluminum alloys, and the technological parameters of welding process was also optimized. The images of droplet transfer were captured by high-speed camera, while the droplet speeds and sizes were statistically analyzed by t tests of independent samples. The results showed that the speeds of droplet arriving at the weld pool were significantly between GMAW and VPPA-GMAW processes, and the droplet speed increases with increasing plasma currents within a certain range. Meanwhile, the droplet momentum in VPPA-GMAW process is larger than that in conventional GMAW process. We also found that as the droplet momentum increased, the depression of weld pool grew more obvious and greatly facilitated the deep-penetration welding. In VPPA-GMAW process, it became more and more easier for the droplet to fall off the wire when the electromagnetic force gradually increased during pulse period. Droplet movement through the arc zone was further accelerated since the central pressure of arc column increased during base period. This research can provide some theoretical support for thick plate welding of high-strength aluminum alloys and help for deeper understanding of the hybrid arc coupling mechanism.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Thomsen JS (2006) Control of pulsed gas metal arc welding. Int J Model Identif Control 1(2):115–125
Wang XW, Huang Y, Zhang YM (2013) Droplet transfer model for laser-enhanced GMAW. Int J Adv Manuf Technol 64(1-4):207–217
Mao YQ, Ke LM, Liu FC, Huang CP, Chen YH, Liu Q (2015) Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of 2060 aluminum lithium alloy. Int J Adv Manuf Technol 81(5-8):1419–1431
Balasubramanian V, Ravisankar V, Reddy GM (2008) Effect of pulsed current welding on mechanical properties of high strength aluminum alloy. Int J Adv Manuf Technol 36(3-4):254–262
Essers WG, Liefkens AC (1972) Plasma-MIG welding developed by Philips. Mach Prod Eng 1(11):632–633
Ono K, Liu ZJ, Era T, Uezono T, Ueyama T, Tanaka M, Nakata K (2009) Development of a plasma MIG welding system for aluminium. Weld Int 23(11):805–809
Sevim I, Hayat F, Kaya Y, Kahraman N, Sahin S (2013) The study of MIG weldability of heat-treated aluminum alloys. Int J Adv Manuf Technol 66(9-12):1825–1834
Yang T, Gao HM, Zhang SH, Wu L (2013) Interface behavior of copper and steel by plasma-MIG hybrid arc welding. Acta Metall Sin (Engl Lett) 26(3):328–332
Hertel M, Fussel U, Schnick M (2014) Numerical simulation of the plasma-MIG process–interactions of the arcs, droplet detachment and weld pool formation. Weld World 58(1):85–92
Bai Y, Gao HM, Lu H, Shi L (2006) Analysis of plasma-MIG arc signal based on LABVIEW. Trans China Weld Inst 27(8):59–62
Bai Y, Gao HM, Qiu L (2010) Droplet transition for plasma-MIG welding on aluminium alloys. Trans Nonferrous Met Soc China 20(12):2234–2239
Ton H (1975) Physical properties of the plasma-MIG welding arc. J Phys D: Appl Phys 8(8):922–933
Terasaki H, Simpson SW (2005) Modelling of the GMAW system in free flight and short circuiting transfer. Sci Technol Weld Joining 10(1):120–124
Essers WG, Walter R (1981) Heat transfer and penetration mechanisms with GMA and plasma-GMA welding. Weld J 60(2):37–42
Resende AA, Ferraresi VA, Scotti A, Dutra JC (2011) Influence of welding current in plasma-MIG weld process on the bead weld geometry and wire fusion rate. Weld Int 25(12):910–916
Chen SJ, Jiang F, Zhang JL, Huang N, Zhang YM (2013) Principle of weld formation in variable polarity keyhole plasma arc transverse welding of aluminum alloy. Trans China Weld Inst 34(4):1–6
Zhang QL, Fan CL, Lin SB, Yang CL (2014) Novel soft variable polarity plasma arc and its influence on keyhole in horizontal welding of aluminium alloys. Sci Technol Weld Joining 19(6):493–499
Woodward NJ, Richardson IM, Thomas A (2000) Variable polarity plasma arc welding of 6.35 mm aluminium alloys: parameter development and preliminary analysis. Sci Technol Weld Joining 5(1):21–25
Han YQ, Zhao P, Du MH, Yao QH (2012) Numerical simulation of aluminum alloys variable polarity plasma arc welding temperature field. Chin J Mech Eng 48(24):33–37
Han YQ, Hong HT, Guo L, Yao QH (2013) Vertical welding of aluminum alloy during variable polarity plasma arc welding process with AC-DC mixing output current. Trans China Weld Inst 34(9):59–62
Zhang W, Hua XM, Liao W, Li F, Wang M (2014) Behavior of the plasma characteristic and droplet transfer in CO2 laser-GMAW-P hybrid welding. Int J Adv Manuf Technol 72(5–8):935–942
Scotti A, Rodrigues CEAL (2009) Determination of momentum as a mean of quantifying the mechanical energy delivered by droplets during MIG/MAG welding. Eur Phys J Appl Phys 45(1):1–8
Waszink JH, Piena MJ (1986) Experimental investigation of drop detachment and drop velocity in GMAW. Weld J 65(11):289–298
Reis RP, Souza D, Scotti A (2011) Models to describe plasma jet, arc trajectory and arc blow formation in arc welding. Weld World 55(3–4):24–32
Lancaster JF (1986) The physics of welding. Pergamon Press, Oxford
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Hong, H., Han, Y., Du, M. et al. Investigation on droplet momentum in VPPA-GMAW hybrid welding of aluminum alloys. Int J Adv Manuf Technol 86, 2301–2308 (2016). https://doi.org/10.1007/s00170-016-8381-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-016-8381-2