Abstract
This paper studies the three-dimensional finite element (FE) modeling for simulating the small-hole drilling process of AISI 1045 by using FE package Abaqus/Explicit. The large deformation of work and the chip formation in drilling process is realized by incorporating Johnson-Cook material constitutive model and material failure criterion. In order to verify the simulation model, the simulation and corresponding drilling tests are performed for the drilling process with 3-mm diameter solid carbide drills at several combination groups of rotational speeds and feed velocities. The estimated thrust force, torque and chip morphology from the simulation are in good agreement with those tested from experiments. The combination of both simulations and experiments not only reveals obvious varying pattern of thrust force, torque with the increasing of rotational speeds and feed velocities, which is consistent with the cutting theory, but also provides a more detailed and profound knowledge about the cutting mechanism including the contribution of chisel edge, drilling stage, and stress and strain distribution, which is assumed to be helpful for the optimization of the drill structure, geometry and drilling parameters.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Gaitonde VN, Karnik SR, Siddeswarappa B, Achyutha BT (2008) Integrating Box-Behnken design with genetic algorithm to determine the optimal parametric combination for minimizing burr size in drilling of AISI 316L stainless steel. Int J Adv Manuf Technol 37(3–4):230–240. doi:10.1007/s00170-007-0957-4
Ozel T, Altan T (2000) Determination of workpiece flow stress and friction at the chip–tool contact for high-speed cutting. Int J Mach Tool Manuf 40(1):133–152. doi:10.1016/S0890- 6955(99)00051-6
Tang L, Huang J, Xie L (2011) Finite element modeling and simulation in dry hard orthogonal cutting AISI D2 tool steel with CBN cutting tool. Int J Adv Manuf Technol 53:1167–1181. doi:10.1007/s00170-010-2901-2
Deng WJ, Xia W, Tang Y (2009) Finite element simulation for burr formation near the exit of orthogonal cutting. Int J Adv Manuf Technol 43:1035–1045. doi:10.1007/s00170-008-1784-y
Guu YH, Deng CS, Hou MT, Hsu CH, Tseng KS (2012) Optimization of machining parameters for stress concentration in microdrilling of titanium alloy. Mater Manuf Process 27(2):207–213. doi:10.1080/10426914.2011.566657
Davim JP, Maranhão C (2009) A study of plastic strain and plastic strain rate in machining of steel AISI 1045 using FEM analysis. Mater Des 30(1):160–165. doi:10.1016/j.mat-des.2008.04.029
Zhou L, Huang ST, Wang D, Yu XL (2011) Finite element and experimental studies of the cutting process of SiCp/Al composites with PCD tools. Int J Adv Manuf Technol 52:619–662. doi:10.1007/s00170-010-2776-2
Zhang YC, Mabrouki T, Nelias D, Gong YD (2011) Chip formation in orthogonal cutting considering interface limiting shear stress and damage evolution based on fracture energy approach. Finite Elem Anal Des 47(7):850–863. doi:10.1016/j.finel.2011.02.016
Özel T (2009) Computational modelling of 3D turning: influence of edge micro-geometry on forces, stresses, friction and tool wear in PcBN tooling. J Mater Process Technol 209(11):5167–5177. doi:10.1016/j.jmatprotec.2009.03.002
Maurel-Pantel A, Fontaine M, Thibaud S, Gelin JC (2012) 3D FEM simulations of shoulder milling operations on a 304L stainless steel. Simul Model Pract Theory 22:13–27. doi:10.1016/j.simpat.2011.10.009
Mao C, Zhou ZX, Ren YH, Zhang B (2010) Analysis and FEM simulation of temperature field in wet surface grinding. Mater Manuf Process 25(6):399–406. doi:10.1080/1042691-0903124811
Singh I, Bhatnagar N, Viswanath P (2008) Drilling of uni-directional glass fiber reinforced plastics: experimental and finite element study. Mater Des 29(2):546–553. doi:10.1016/j.matdes.2007.01.029
Isbilir O, Ghassemieh E (2012) Finite element analysis of drilling of carbon fibre reinforced composites. Appl Compos Mater 19(3–4):637–656. doi:10.1007/s10443-011-9224-9
Durão LMP, De Moura M, Marques AT (2008) Numerical prediction of delamination onset in carbon/epoxy composites drilling. Eng Fract Mech 75(9):2767–2778. doi:10.1016/j.engfrac-mech.2007.03.009
Phadnis VA, Makhdum F, Roy A, Silberschmidt VV (2013) Drilling in carbon/epoxy composites: experimental investigations and finite element implementation. Compos A:Appl Sci 47:41–51. doi:10.1016/j.compositesa.2012.11.020
Gök K, Türkes E, Neseli S, Saglam H, Gök A (2013) The validation as experimental and numerical of the values of thrust force and torque in drilling process. J Eng Sci Technol Rev 6(3):93–99
Guo YB, Dornfeld DA (2000) Finite element modeling of burr formation process in drilling 304 stainless steel. J Manuf Sci Eng 122(4):612–619. doi:10.1115/1.1285885
Muhammad R, Ahmed N, Shariff YM, Silberschmidt VV (2012) Finite-element analysis of forces in drilling of Ti-alloys at elevated temperature. Solid State Phenom 188:250–255. doi:10.4028/www.scientific.net/SSP.188.250
Wu HB, Jia ZX, Zhang XC, Liu G (2012) Study on simulation and experiment of drilling for titanium alloys. Mater Sci Forum 704:657–663. doi:10.4028/www. scientific.net/MSF.704-705.657
Isbilir O, Ghassemieh E (2011) Finite element analysis of drilling of titanium alloy. In: 11th International Conference on the Mechanical Behavior of Materials 10: 1877–1882. doi: 10.1016/j.proeng.2011.04.312
Endo H, Murahashi T, Marui E (2007) Accuracy estimation of drilled holes with small diameter and influence of drill parameter on the machining accuracy when drilling in mild steel sheet. Int J Mach Tool Manuf 47(1):175–181. doi:10.1016/j.ijmachtools.2006.02.001
Liu HT (2007) Hole drilling with abrasive fluidjets. Int J Adv Manuf Technol 32(9–10):942–957. doi:10.1007/s00170-005-0398-x
Zitoune R, Krishnaraj V, Collombet F (2010) Study of drilling of composite material and aluminium stack. Compos Struct 92(5):1246–1255. doi:10.1016/j.compstruct.2009.10.010
Tsao CC, Hocheng H (2004) Taguchi analysis of delamination associated with various drill bits in drilling of composite material. Int J Mach Tool Manuf 44(10):1085–1090. doi:10.1016/j.ijmachtools.2004.02.019
Johnson GR, Cook WH (1983) A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures. In: Proceedings of the seventh international symposium on ballistics, Hague, pp. 541–547
Iqbal SA, Mativenga PT, Sheikh MA (2007) Characterization of machining of AISI 1045 steel over a wide range of cutting speeds. Part 2: evaluation of flow stress models and interface friction distribution schemes. P I Mech Eng B J Eng 221(5):917–926. doi:10.1243/ 09544054JEM797
Rech J, Claudin C, D’Eramo E (2009) Identification of a friction model—application to the context of dry cutting of an AISI 1045 annealed steel with a TiN-coated carbide tool. Tribol Int 42(5):738–744. doi:10.1016/j.triboint.2008.10.007
Adibi-Sedeh AH, Vaziri M, Pednekar V, Madhavan V, Ivester RW (2005) Investigation of the effect of using different material models on finite element simulations of machining. In: Proceeding of the 8th CIRP International Workshop on Modeling of Machining Operations, Chemnitz, Germany, pp. 215–224
Jaspers S, Dautzenberg JH (2002) Material behaviour in conditions similar to metal cutting: flow stress in the primary shear zone. J Mater Process Tech 122(2):322–330. doi:10.1016/S0924-0136(01)01228-6
Abaqus 6.11 Documentation. Abaqus/CAE user’s manual, 2011
Duan CZ, Dou T, Cai YJ, Li YY (2009) Finite element simulation and experiment of chip formation process during high speed machining of AISI 1045 hardened steel. Int J Recent Trends Eng 1(5):46–50
Özel T (2006) The influence of friction models on finite element simulations of machining. Int J Mach Tool Manuf 46(5):518–530. doi:10.1016/j.ijmachtools.2005.07.001
Zorev NN (1963) Inter-relationship between shear processes occurring along tool face and shear plane in metal cutting. Int Res Prod Eng 42–49
Childs THC, Maekawa K (1990) Computer-aided simulation and experimental studies of chip flow and tool wear in the turning of low alloy steels by cemented carbide tools. Wear 139:235–250
Liu CR, Guo YB (2000) Finite element analysis of the effect of sequential cuts and tool–chip friction on residual stresses in a machined layer. Int J Mech Sci 42:1069–1086. doi:10.1016/S0020-7403(99)00042-9
Haglund AJ, Kishawy HA, Rogers RJ (2008) An exploration of friction models for the chip–tool interface using an Arbitrary Lagrangian–Eulerian finite element model. Wear 265(3):452–460. doi:10.1016/j.wear.2007.11.025
Grzesik W (2006) Determination of temperature distribution in the cutting zone using hybrid analytical–FEM technique. Int J Mach Tool Manuf 46(6):651–658. doi:10.1016/j.ijmach- tools.2005.07.009
Shaw MC (2004) Metal cutting principals. Oxford University Press, USA
Astakhov VP (2006) Tribology of metal cutting, 1st Ed. Elsevier Science Publishing Company
Barry J, Byrne G (2002) The mechanisms of chip formation in machining hardened steels. J Manuf Sci Eng Trans ASME 124:528–535. doi:10.1115/1.1455643
Sun J, Guo YB (2008) A new multi-view approach to characterize 3D chip morphology and properties in end milling titanium Ti-6Al-4 V. Int J Mach Tools Manuf 48:1486–1494. doi:10.1016/j.ijmachtools.2008.04.002
Farid AA, Sharif S, Idris MH (2011) Chip morphology study in high speed drilling of Al-Si alloy. Int J Adv Manuf Technol 57(5–8):555–564. doi:10.1007/s00170-011-3325-3
Trent EM, Wright PK (2000) Metal cutting, 4th edn. Butterworth–Heinemann, Massachusetts
Paul A, Kapoor SG, DeVor RE (2005) Chisel edge and cutting lip shape optimization for improved twist drill point design. Int J Mach Tool Manuf 45(4):421–431. doi:10.1016/ j.ijmachtools.2004.09.010
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Nan, X., Xie, L. & Zhao, W. On the application of 3D finite element modeling for small-diameter hole drilling of AISI 1045 steel . Int J Adv Manuf Technol 84, 1927–1939 (2016). https://doi.org/10.1007/s00170-015-7782-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-7782-y