Abstract
The joint characteristics of thin-walled pipe friction-welded joint between AA6063 aluminum alloy (A6063) and AISI 304 stainless steel (SUS304) were investigated. The pipe had a thickness of 1.5 mm, and the joint was made with a friction speed of 27.5 rps and a friction pressure of 30 MPa. The joint, which was made by a continuous drive friction welding machine, had heavy deformation on the A6063 side during braking. To prevent deformation until rotation stop with braking, the joint was made by a technique in which the relative speed between both specimens instantly decreased to 0 when the setting friction time was finished, and consequently, the joining could be successfully achieved. The joint with a friction pressure of 30 MPa and a friction time of 0.4 s did not have the intermetallic compound (IMC) layer (interlayer) at the weld interface, although that with a friction time of 1.6 s had it. However, the joint with a forge pressure of 150 MPa had the A6063 side buckling. Moreover, the joint efficiency of the joint with flash was higher than that of the joint without flash because the inner flash of A6063 was stuck to the inner surface of the SUS304 side. Therefore, the joint should be made with the opportune friction time without the IMC interlayer and with the opportune forge pressure without buckling, and the accurate joint efficiency should be evaluated without flash.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Mitani K, Matsui S, Matsumura H, Hasegawa H, Tamura T, Kousaka S, Ishizaka Y, Sakimoto S (1992) Effect of high frequency preheating on plasma welding speed for SUS304 tube. Q J Jpn Weld Soc 10(2):223–228 (in Japanese)
Asai S (1999) Current trends of arc welding in plant piping. J Jpn Weld Soc 68(8):601–606 (in Japanese)
Inoue Y (1985) Diffusion bonding by HIP. J Jpn Weld Soc 54(1):50–55 (in Japanese)
Koizumi M (1987) Development and new application of HIP technique. J High Pres Inst Jpn 25(6):321–330 (in Japanese)
Somani MC, Birla NC, Tekin A (1998) Solid-state diffusion welding of wrought AISI 304 stainless steel to nimonic AP-1 superalloy powder by hot isostatic pressing. Weld J (supplement) 77(2):59s–65s
Wu Z, Mei J, Voice W, Beech S, Wu X (2011) Microstructure and properties of diffusion bonded Ti-6Al-4V parts using brazing-assisted hot isostatic pressing. Mater Sci Eng A 528(24):7388–7394
Zhao Y, Li C, Huang B, Liu S, Huang Q (2014) Verification of the effect of surface preparation on hot isostatic pressing diffusion bonding joints of CLAM steel. J Nucl Mater 455(1/3):486–490
Morii Y (1972) Joining stainless steel to aluminium—transition joints for cryogenic use. J Light Met Weld 10(114):266–270 (in Japanese)
Kakimoto E (2000) Joint material of aluminum and stainless steel for welding. J Light Met Weld Constr 38(1):15–21 (in Japanese)
Aritoshi M, Okita K (2002) Friction welding of dissimilar metals. J Jpn Weld Soc 71(6):432–436 (in Japanese)
American Welding Society (1982) Welding handbook, vol 4, 7th edn. American Welding Society, Miami, pp 537–538
Wang KK (1975) Friction welding. Weld Res Counc Bull 204:1–21
Maalekian M (2007) Friction welding—critical assessment of literature. Sci Technol Weld Join 12(8):738–759
Kawai G, Ogawa K, Tsujino R, Tokisue H (1999) Statistical strength characteristics of aluminum alloy pipe and carbon steel pipe friction weld joints. J Jpn Soc Str Fract Mats 33(1):1–10
Ohkubo Y, Iwamura S, Hatta H (2007) Thermal analysis on friction welding of carbon steel tube and AA5154 aluminum tube. Sumitomo Light Met Tech Rep 48(1):27–32 (in Japanese)
Eberhard BJ, Schaaf BW Jr, Wilson AD (1983) Friction weld ductility and toughness as influenced by inclusion morphology. Weld J (supplement) 62(7):171s–178s
Ogawa K, Nakayama H, Ohue Y, Hasui A (1988) Fatigue strength characteristics of S35C/S35C friction welded tubular butt joints. J Soc Mater Sci Jpn 37(421):1209–1215 (in Japanese)
Kumar MV, Balasubramanian V (2014) Microstructure and tensile properties of friction welded SUS 304HCu austenitic stainless steel tubes. Int J Pres Ves Pip 113:24–31
Kimura M, Ichihara A, Kusaka M, Kaizu K (2012) Joint properties and their improvement of AISI 310S austenitic stainless steel thin walled circular pipe friction welded joint. Mater Des 38:38–46
Kimura M, Saitoh Y, Kusaka M, Kaizu K, Fuji A (2011) Effect of friction welding condition and weld faying surface properties on tensile strength of friction welded joint between pure titanium and pure copper. J Solid Mech Mater Eng 5(12):849–865
Kimura M, Inui Y, Kusaka M, Kaizu K, Fuji A (2015) Joining phenomena and tensile strength of friction welded joint between pure aluminum and pure copper. Mech Eng J 2(1), No.14-00328
Japan Light Metal Association (2007) Aluminium handbook, 7th edn. Japan Light Metal Association, Tokyo, pp 1–23 (in Japanese)
Nelson TW, Steel RJ, Arbegast WJ (2003) In situ thermal studies and post-weld mechanical properties of friction stir welds in age hardenable aluminium alloys. Sci Technol Weld Join 8(4):283–288
Takaya K, Harada Y, Kumai S, Kitayama K (2012) Microstructure of joint interface and mechanical properties in high-speed solid-state welded 2024 aluminum alloy stud and 6N01 aluminum alloy plate. J Jpn Inst Light Met 62(10):376 (in Japanese)
Mizuno M, Takada T, Katoh S (1967) Weldability of high strength Al-Zn-Mg alloy (report 1)—aging characteristics of heat-affected zone. J Jpn Weld Soc 36(8):854–861 (in Japanese)
Mizuno M, Matsumura Y, Ogihara A (1970) Weldability of high strength Al-Zn-Mg alloy (report 2)—aging characteristics of pure Al-Zn-Mg ternary alloys. J Jpn Weld Soc 39(1):73–82 (in Japanese)
Katayama S, Ogawa K (2010) Laser weldability and aging characteristics of welds—laser weldability of commercially available A7N01 alloy (1). J Light Met Weld 48(12):463–474 (in Japanese)
Kimura M, Choji M, Kusaka M, Seo K, Fuji A (2005) Effect of friction welding conditions and aging treatment on mechanical properties of A7075-T6 aluminium alloy friction welds. Sci Technol Weld Join 10(4):406–412
Kimura M, Seo K, Kusaka M, Fuji A (2003) Observation of joining phenomena in friction stage and improving friction welding method. JSME Int J (Series A) 46(3):384–390
Fukumoto S, Tsubakino H, Okita K, Aritoshi M, Tomita T (1999) Friction welding process of 5052 aluminium alloy to 304 stainless steel. Mater Sci Technol 15:1080–1086
Reddy GM, Rao AS, Mohandas T (2008) Role of electroplated interlayer in continuous drive friction welding of AA6061 to AISI 304 dissimilar metals. Sci Technol Weld Join 13(7):619–628
Sahin M (2009) Joining of stainless-steel and aluminium materials by friction welding. Int J Adv Manuf Technol 41:487–497
Shubhavardhan RN, Surendran S (2012) Friction welding to join dissimilar metals. Int J Emerg Technol Adv Eng 2(7):200–210
Ashfaq M, Sajja N, Rafi HK, Rao P (2013) Improving strength of stainless steel/aluminum alloy friction welds by modifying faying surface design. J Mater Eng Perform 22(2):376–383
Bozzi S, Helbert-Etter AI, Baudin T, Criqui B, Kerbiguet JG (2010) Intermetallic compounds in Al 6061/IF-steel friction stir spot welds. Mater Sci Eng A 527(16/17):4505–4509
Qui R, Iwamoto C, Satonaka S (2009) Interfacial microstructure and strength of steel/aluminum alloy joints welded by resistance spot welding with cover plate. J Mater Process Technol 209(8):4186–4193
Wang N, Yamaguchi T, Nishio K (2013) Interfacial microstructure and strength of aluminum alloys/steel spot welded joints. J Jpn Inst Met Mater 77(7):259–267 (in Japanese)
Rathod M, Kutsuna M (2003) Laser roll bonding of A5052 aluminium alloy and SPCC steel. Q J Jpn Weld Soc 21(2):282–294 (in Japanese)
Sierra G, Peyre P, Deschaux-Beaume F, Stuart D, Fras G (2007) Steel to aluminium key-hole laser welding. Mater Sci Eng A 447(1/2):197–208
Su Y, Hua X, Wu Y (2013) Effect of input current modes on intermetallic layer and mechanical property of aluminum-steel lap joint obtained by gas metal arc welding. Mater Sci Eng A 578(20):340–345
Materials Science Society of Japan (1995) Principle of intermetallic compound. Shokabo Publishing, Tokyo, pp 118–120 (in Japanese)
Sahin M (2010) Joining of aluminium and copper materials with friction welding. Int J Adv Manuf Technol 49:527–534
Itoh Y, Shindo T, Saitoh M, Tezuka M (1998) Strength characteristics of copper/aluminum alloy friction welded joint. Trans Jpn Soc Mech Eng Ser A 64(624):2197–2202 (in Japanese)
Kimura M, Choji M, Kusaka M, Seo K, Fuji A (2006) Effect of friction welding conditions on mechanical properties of A5052 aluminium alloy friction welded joint. Sci Technol Weld Join 11(2):209–215
Kato K, Tokisue H (1994) Properties of friction welded joint of 6061 aluminium alloy. J Light Met Weld Constr 32(5):203–209 (in Japanese)
Lee WB, Yoen YM, Kim DU, Jung SB (2003) Effect of friction welding parameters on mechanical and metallurgical properties of aluminium alloy 5052-A36 steel joint. Mater Sci Technol 19:773–778
Kimura M, Seo K, Kusaka M, Fuji A (2005) Improving joint properties of friction welded joint of high tensile steel. JSME Int J (Series A) 48(4):399–405
Kimura M, Kusaka M, Seo K, Muramatsu Y (2006) Properties and improvement of super fine grained steel friction welded joint. Sci Technol Weld Join 11(4):448–454
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kimura, M., Kusaka, M., Kaizu, K. et al. Friction welding technique and joint properties of thin-walled pipe friction-welded joint between type 6063 aluminum alloy and AISI 304 austenitic stainless steel. Int J Adv Manuf Technol 82, 489–499 (2016). https://doi.org/10.1007/s00170-015-7384-8
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-7384-8