Abstract
Currently, electrical discharge machining (EDM) is the established manufacturing process for making holes through Ni superalloy turbine blades to facilitate blade cooling. Surface integrity of these sub-millimetre holes is of paramount importance since it directly influences the fatigue life of the component. In this paper, EDM is compared against laser and mechanical micro-hole drilling of Inconel 718 alloy. The motivation was to assess alternative manufacturing methods for raising the quality threshold of micro-drilled holes. Mechanical and metallurgical characterisation of surface and subsurface regions of the holes produced by the three processes was undertaken using backscatter electron (BSE) microscopy, electron backscatter diffraction (EBSD) and nano-indentation techniques to assess surface hardness, grain misorientation, plastic deformation and the heat-affected zone. The results suggest that mechanical micro-drilling offers improved mechanical, metallurgical and geometrical properties compared to both laser and EDM processes.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Bradbury SR, Huyanan T (2000) Challenges facing surface engineering technologies in the cutting tool industry. Vacuum 56(3):173–177
Stephen L, Kursad S, Lin L, Clive G-R, Martyn C (2009) Statistical analysis of recast formation in laser drilled acute blind holes in CMSX-4 nickel superalloy. Int J Adv Manuf Technol 43:1094–1105
Thao O, Joshi SS (2008) Analysis of heat affected zone in the micro-electric discharge machining. Int J Manuf Technol Manag 13(2/3/4):201–213
Newton TR, Melkote SN, Watkins TR, Trejo RM, Reister L (2009) Investigation of the effect of process parameters on the formation and characteristics of recast layer in wire-EDM of Inconel 718. Mater Sci Eng A 513–514:208–215
Aspinwall DK, Soo SL, Berrisford AE, Walder G (2008) Workpiece surface roughness and integrity after WEDM of Ti–6Al–4 V and Inconel 718 using minimum damage generator technology. CIRP Ann Manuf Technol 57:187–190
Bleys P, Kruth J-P, Lauwers B, Schacht B, Balasubramanian V, Froyen L, van Humbeeck J (2006) Surface and sub-surface quality of steel after EDM. Adv Eng Mater 8(1–2):15–25
Field M, Kahles JF, Koster WP (1966) The surface effects produced in nonconventional metal removal- comparison with conventional machining techniques. Met Eng Q Am Soc Met 6:32–45
Tolinski M (2006) Smaller holes-bigger challenges: holemaking in tough materials serves more demanding aircraft. Manuf Eng 136(3):95–108
Salkind M (1989) Aerospace materials research opportunities. Angewandte Chemie. Int Ed Engl 28(5):655–662
Serebryakov VA, Volkov MV, Zhang X (2005) Laser drilling of microholes in refractory alloys. J Opt Technol 72(3):241–244
Dubey AK, Yadava V (2008) Laser beam machining- a review. Int J Mach Tools Manuf 48:609–628
Bandyopadhyay S, Sarin Sundar JK, Sundararajan G, Joshi SV (2002) Geometrical features and metallurgical characteristics of Nd:YAG laser drilled holes in thick IN 718 and Ti-6Al-4 V sheets. J Mater Process Technol 127:83–95
Chien W-T, Hou S-C (2007) Investigation the recast layer formed during laser trepan drilling of Inconel 718 using Taguchi method. Inter J Adv Manuf Technol 33:308–316
Sezer HK, Li L, Schmidt M, Pinkerton AJ, Anderson B, Williams P (2006) Effect of beam angle on HAZ, recast and oxide layer characteristics in laser drilling of TBC nickel superalloys. Int J Mach Tools Manuf 46:1972–1982
Allan D, Almond H, Logan P (2000) A technical comparison of micro-electrodischarge machining, microdrilling and copper vapour laser machining for the fabrication of ink jet nozzles. Proc SPIE 4019:531–540
Ion JC (2005) Laser processing of engineering materials: principles, procedure and industrial application. Elsevier Butterworth-Heinemann
Zhang JH, Lee TC, Ai X, Lau WS (1996) Investigation of the surface integrity of laser cut ceramic. J Mater Process Technol 57:304–310
Feifer A (1989) Drilling micro-size deep holes. Tool Prod 55(7):1–2
Sharman ARC, Amarashighe A, Ridgway K (2008) Tool life and surface integrity aspects when drilling and hole making in Inconel 718. J Mater Process Technol 200(1):424–432
Kwong J, Axinte DA, Withers PJ (2009) The sensitivity of Ni-based superalloy to hole making operations: influence of process parameters on subsurface damage and residual stress. J Mater Process Technol 209(8):3968–3977
Rahim E, Sasahara H (2009) Application of minimum quantity lubrication when drilling nickel-based superalloy at high cutting speed. Key Eng Mater 407:612–615
Axinte DA, Andrews P (2007) Some considerations on tool wear and workpiece surface quality of holes finished by reaming or milling in a nickel base superalloy. Proc Inst Mech Eng B J Eng Manuf 221(4):591–603
Imran M, Mativenga PT, Gholinia A, Withers PJ (2010) Evaluation of the surface integrity in micro drilling process for nickel based superalloy. Int J Adv Manuf Technol. Published online on Dec. 23, 2010
Imran M, Mativenga PT, Gholinia A, Withers PJ (2014) Comparison of tool wear mechanisms and surface integrity for dry and wet micro-drilling of nickel base superalloys. Int J Mach Tools Manuf 76:49–60
Lee K, Dornfeld DA (2005) Micro-burr formation and minimization through process control. Precis Eng 29(2):246–252
Imran M, Mativenga PT, Kannan S (2010) An investigation into the effects of tool geometry in micro drilling process for nickel based superalloy. The 5th International Conference on Micro-Manufacturing ICOMM / 4 M, Madison, 85 - 93 April 5-8
Imran M (2010) Feasibility and process development of mechanical micro drilling for nickel based super alloys. PhD thesis, The University of Manchester, U.K
Masuzawa T (2000) State of the art of micromachining. CIRP Ann Manuf Technol 49(2):473–488
Jaffery SI, Khan M, Ali L, Mativenga PT (2014) Statistical analysis of process parameters in micromachining of Ti-6Al-4 V alloy. Proc IMechE B J Eng Manuf. doi:10.1177/0954405414564409
Okasha MM, Mativenga PT, Driver N, Li L (2010) Sequential laser and mechanical micro-drilling of Ni superalloy for aerospace application. CIRP Ann Manuf Technol 59(1):199–202
Kuppan P, Rajadurai A, Narayanan S (2008) Influence of EDM process parameters in deep hole drilling of Inconel 718. Int J Adv Manuf Technol 38:74–84
Imran M, Mativenga PT, Kannan S, Novovic D (2008) An experimental investigation of deep-hole microdrilling capability for a nickel-based superalloy. Proc Inst Mech Eng B J Eng Manuf 222(12):1589–1596
Imran M, Mativenga PT, Withers PJ (2012) Assessment of machining performance using wear map approach in micro-drilling. Int J Adv Manuf Technol 59(1–4):119–126
Mustafa A, Ulas C, Hascalik A (2013) Optimization of micro-EDM drilling of inconel 718. Int J Adv ManufTechnol 66:1015–1023
Imran M, Mativenga PT, Gholinia A, Withers PJ (2011) Evaluation of the surface integrity in micro drilling process for nickel based superalloy. Int J Adv Manuf Technol 55(5–8):465–476
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Imran, M., Mativenga, P.T., Gholinia, A. et al. Assessment of surface integrity of Ni superalloy after electrical-discharge, laser and mechanical micro-drilling processes. Int J Adv Manuf Technol 79, 1303–1311 (2015). https://doi.org/10.1007/s00170-015-6909-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-6909-5