Abstract
Surface structuring on cutting tools is a modern application of surface structuring that has shown improvements in tribological phenomena at tool-chip interface. Literature suggests that this technique has been used mainly to structure the rake face of a cutting tool. This study reports on the performance of femtosecond laser-generated structures on both rake and flank faces of the cutting tool. The premise for fabricating structures on both faces of cutting tool was to have strong impact on tool wear and cutting forces so as to reduce power demands. Fabricated structures were in a form of conventional micro-grooves. Performance of structures was assessed in the machining of AISI/SAE 4140 over a conventional range of cutting speeds for the selected workpiece material. The orthogonal cutting tests to investigate the effects of structured tool on cutting forces, friction coefficient and flank land wear rate were performed. Results show that the structured tool is effective in delivering better machining performance as compared to unstructured tool in terms of reduced friction coefficient by 14 %, cutting forces by 10 %, feed forces by 23 %, and compression ratio by 10 %. Characterisation of sticking and sliding contact was evaluated.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Da Silva WM, Suarez MP, Machado AR, Costa HL (2013) Effect of laser surface modification on the micro-abrasive wear resistance of coated cemented carbide tools. Wear 302:1230–1240
Koshy P, Tovey J (2011) Performance of electrical discharge textured cutting tools. CIRP Ann Manuf Technol 60:153–156
Lei S, Devarajan S, Chang Z (2009) A study of micropool lubricated cutting tool in machining of mild steel. J Mater Process Technol 209:1612–1620
Jianxin D, Ze W, Yunsong L, Ting Q, Jie C (2012) Performance of carbide tools with textured rake-face filled with solid lubricants in dry cutting processes. Int J Refract Met Hard Mater 30:164–172
Xing Y, Deng J, Zhao J, Zhang G, Zhang K (2014) Cutting performance and wear mechanism of nanoscale and microscale textured Al2O3/TiC ceramic tools in dry cutting of hardened steel. Int J Refract Met Hard Mater 43:46–58
Kawasegi N, Sugimori H, Morimoto H, Morita N, Hori I (2009) Development of cutting tools with microscale and nanoscale textures to improve frictional behavior. Precis Eng 33:248–254
Obikawa T, Kamio A, Takaoka H, Osada A (2011) Micro-texture at the coated tool face for high performance cutting. Int J Mach Tools Manuf 51:966–972
Ze W, Jianxin D, Yang C, Youqiang X, Jun Z (2012) Performance of the self-lubricating textured tools in dry cutting of Ti-6Al-4 V. Int J Adv Manuf Technol 62:943–951
Enomoto T, Watanabe T, Aoki Y, Ohtake N (2007) Development of a cutting tool with micro structured surface. Trans Jpn Soc Mech Eng Ser C 73:1560–1565
Wen-long S, Jian-xin D, Zhi-junc W (2009) Machining performance of micro-pool tools. Tribology 02:002
Wu Z, Deng J, Su C, Luo C, and Xia D. Performance of the micro-texture self-lubricating and pulsating heat pipe self-cooling tools in dry cutting process. International Journal of Refractory Metals and Hard Materials. 2014
Xie J, Luo MJ, Wu KK, Yang LF, Li DH (2013) Experimental study on cutting temperature and cutting force in dry turning of titanium alloy using a non-coated micro-grooved tool. Int J Mach Tools Manuf 73:25–36
Lian Y, Deng J, Yan G, Cheng H, Zhao J (2013) Preparation of tungsten disulfide (WS2) soft-coated nano-textured self-lubricating tool and its cutting performance. Int J Adv Manuf Technol 68:2033–2042
Sugihara T, Enomoto T (2013) Crater and flank wear resistance of cutting tools having micro textured surfaces. Precis Eng 37:888–896
Xing Y, Deng J, Zhang K, Zhang G, Gao H (2014) Effect of femtosecond laser pretreatment on wear resistance of Al2O3/TiC ceramic tools in dry cutting. Int J Refract Met Hard Mater 43:291–301
Fatima A and Mativenga P. Performance of flank face structured cutting tools in machining of AISI/SAE 4140 over a range of cutting speeds. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture.(accepted). 2014.
Sugihara T, Enomoto T (2012) Improving anti-adhesion in aluminum alloy cutting by micro stripe texture. Precis Eng 36:229–237
Jianxin D, Wenlong S, Hui Z (2009) Design, fabrication and properties of a self-lubricated tool in dry cutting. Int J Mach Tools Manuf 49:66–72
Kawasegi N, Sugimori H, Morita N, and Hori I, “Development of small diameter drills with micro/nanometer scale textures,” presented at the International forum of micro manufacturing Japan, 2010
Ling T, Liu P, Xiong S, Grzina D, Cao J, Wang QJ, Xia ZC, Talwar R (2013) Surface texturing of drill bits for adhesion reduction and tool life enhancement. Tribol Lett 52:113–122
Chang W, Sun J, Luo X, Ritchie JM, Mack C (2011) Investigation of microstructured milling tool for deferring tool wear. Wear 271:2433–2437
Fatima A and Mativenga P. Assessment of tool rake surface structure geometry for enhanced contact phenomena. The International Journal of Advanced Manufacturing Technology. 2013;1–6
Fatima A, Whitehead DJ, Mativenga PT (2014) Femtosecond laser surface structuring of carbide tooling for modifying contact phenomena. Proc IME B J Eng Manufact 228:1325–1337
Fatima A, Mativenga PT (2013) A review of tool–chip contact length models in machining and future direction for improvement. Proc IME B J Eng Manufact 227:345–356
F. P. Bowden and Tabor D, The friction and lubrication of solids 2001: Oxford University Press.
Fang N, JAWAHIR IS (2003) Analytical prediction of the chip back-flow angle in machining with restricted contact grooved tools. J Manuf Sci Eng 125:210–219
Jawahir IS, Li PX, Gosh R, Exner EL (1995) A New parametric approach for the assessment of comprehensive tool wear in coated grooved tools. CIRP Ann Manuf Technol 44:49–54
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Fatima, A., Mativenga, P.T. A comparative study on cutting performance of rake-flank face structured cutting tool in orthogonal cutting of AISI/SAE 4140. Int J Adv Manuf Technol 78, 2097–2106 (2015). https://doi.org/10.1007/s00170-015-6799-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-6799-6