Abstract
Using tailor-welded blanks (TWB) in automotive industry is on the rise. This is done due to advantages such as reduction in weight leading to more effective operational cost and lower energy consumption of vehicles. The main objective of this investigation was to study the effect of location change of weld zone and differences in thickness combination of TWB sheets on their tensile characteristics and forming capabilities. Quality evaluations of weld zone metallographic and tensile as well as ball punch tests have been conducted. Tension characteristics of welded samples have been determined by conducting a uni-axial tensile test perpendicular on the weld line in those samples. Forming capability of TWB samples were also studied by using sphere head chisel test. By moving weld line toward thick sheets direction and increasing thin sheets share of the weld in TWB, an increase in relative elongation in tensile test and in chisel test increase in cups height was observed. This indicates that forming capability of TWB samples by moving weld line toward thick sheet increases and weld zone does not have much effect on forming capability of TWB. By using the derived recommended relation induced from this study, it is conceivable to obtain the amount of increase in relative length of TWB from its base sheets. Results of this relation are confirmed with obtained results from tensile test. Also by reduction in thickness difference of TWB sheets, their formability increases.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Tusek J (2001) Welding of tailored blanks of different materials. J Mater Process Technol 119:180–184
Auto/Steel Partnership (1995) Tailor welded blank design and manufacturing manual, Technical Report
Dawes C (1992) Laser welding, a practical guide. Abington, Cambridge
Duley WW (1999) Laser welding. Wiley, New York
Panda SKD, Ravi Kumar D, Kumar H, Nath AK (2007) Characterization of tensile properties of tailor welded IF steel sheets and their formability in stretch forming. J Mater Process Technol 183:321–332
Baptista AJ, Rodrigues DM, Menezes LF (2006) Influence of the weld on the mechanical behavior of tailor welded blanks. Mater Sci 514–516:1493–1500
Abdullah K, Wild PM, Jeswiet JJ, Ghasempoor A (2001) Tensile testing for weld deformation properties in similar gage tailor welded blanks using the rule textures. J Mater Process Technol 112:91–97
Gaied S, Roelandt J, Pinard F, Schmit F, Balabane M (2009) Experimental and numerical assessment of tailor-welded blanks formability. J Mater Process Technol 210:387–395
Chan SM, Chan LC, Lee TC (2003) Tailor-welded blanks of different thickness ratios effects on forming limit diagrams. J Mater Process Technol 132:95–101
Cheng CH, Chan LC, Chow CL (2007) Weldment properties evaluation and formability study of tailor-welded blanks of different thickness combinations and welding orientations. J Mater Sci 42:5982–5990
Mustafa A, Ahmetoglu D, Brouwers L, Shulkin L, Taupin G, Kinzel L, Altan T (1995) Deep drawing of round cups from tailor-welded blanks. J Mater Process Technol 53:684–694
British Standard EN ISO 13919-2 (2001)
British Standard EN ISO 15614-11 (2002)
STM Standard E 8M (2001)
ASTM Standard E 643 (2001)
Shao H, Gould J, Albright CH (2007) Laser blank welding high-strength steels. Metall Mater Trans 38:321–331
Hosfort WH, Caddel RM (1978) Metal forming, mechanical and metallurgy. Cambridge University Press, Cambridge
Hiam J, Lee A (1978) Factors influencing the forming limit curves of sheet steel. Sheet Metal Ind J 55:631–643
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Riahi, M., Amini, A. Effect of different combinations of tailor-welded blank coupled with change in weld location on mechanical properties by laser welding. Int J Adv Manuf Technol 67, 1937–1945 (2013). https://doi.org/10.1007/s00170-012-4620-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-012-4620-3