Abstract
Pulsed wave fibre lasers are becoming a popular industrial tool in microprocessing due to their many positive features, such as high beam quality, high reliability and high productivity, which are fundamental to machining small, precise features of industrial applications. However, the lasers’ use in the machining of ultraprecise features, such as small holes, is hindered by the fact that commercial pulsed wave fibre lasers commonly operate with pulse durations in the nanosecond regime. Such long pulse durations mean that the material is thermally removed, which results in the production of a melted layer and thermal damage in the bulk material. Consequently, the typical thermal defects of the melting regime, such as spattering of recast material around the hole, taper, heat-affected zone and poor hole circularity, are found in materials machined with these lasers. This paper proposes a design for an innovative nozzle that combines the high productivity of nanosecond fibre lasers with an improvement in the quality of the machined holes by reducing the spatter production in titanium laser percussion drilling. The innovative nozzle is based on the suction effect created by the Venturi principle that prevents the deposition of melted and vaporised material on the workpiece surface. The influence of the nozzle configuration and shielding gas on hole quality is investigated after the laser percussion drilling of 0.5-mm-thick titanium sheets, in which the process conditions that allow maximum productivity are used. The innovative nozzle produces a remarkable decrease in spatter on the entrance hole surface without affecting the other quality features, such as hole diameter, circularity and taper, while preserving the high productivity obtainable with a standard nozzle.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Chichkov BN, Momma C, Nolte S, Von Alvensleben F, Tünnermann A (1996) Short-pulse laser ablation of solid targets. Opt Commun 129(1–2):134–142
Pronko PP, Dutta SK, Squier J, Rudd JV, Du D, Mourou G (1995) Machining of sub-micron holes using a femtosecond laser at 800 nm. Opt Commun 114(1–2):106–110
Tam SC, Willams R, Yang LJ, Jana S, Lim LEN, Lau MWS (1995) A review of the laser processing of aircraft components. J Mater Process Tech 23:177–194
Dijk MHHV, Vlieger GD, Brouwer JE(1989) Laser precision hole drilling in aero-engine components. Proceedings of the sixth international conference on lasers in manufacturing, Springer, Berlin 237–247
Corfe AG (1983) Laser drilling of aero-engine components. Proceedings of the first international conference on lasers in manufacturing, Springer, Berlin 31–38
Naeem M, Chinn J (2008) Advancement in laser drilling for aerospace gas turbines. Proceedings of PICALEO 197–202
Hainsey RF, Hooper AE, Swenson EJ, Nashner MS (2006) Recent advances in laser micromachining for semiconductors and microfluidic applications. Proceedings of ICALEO203–212
Meijer J, Du K, Gilner A, Hoffmann D, Kovalenko VS, Masuzawa T, Ostendorf A, Poprawe R, Schulz W (2002) Laser machining by short and ultrashort pulses, state of the art and new opportunities in the age of the photons. CIRP Ann Manuf Technol 51(2):531–550
Bandyopadhyay S, Sundar JK, Sundararajan G, Joshi SV (2002) Geometrical features and metallurgical characteristics of Nd:Yag laser drilled holes in thick IN718 and Ti-6Al-4V sheets. J Mater Process Tech 127:83–95
Hallgren C, Reimers H, Chakarov D, Gold J, Wennerberg A (2003) An in vivo study of bone response to implants topographically modified by laser micromachining. Biomaterials 24:701–710
Low DKY, Li L, Byrd PJ (2003) Spatter prevention during the laser drilling of selected aerospace materials. J Mater Process Tech 139:71–76
Kudesia SS, Solana P, Rodden W, Hand DP, Jones J (2005) Appropriate regimes of laser drilling models containing melt eject mechanisms. J Laser Appl 14:159–164
Yilbas BS (1997) Parametric study to improve laser hole drilling process. J Mater Process Technol 70:264–273
Zhang Y, Faghri A (1999) Vaporization, melting and heat conduction in the laser drilling process. Int J Heat Mass Transf 42:1775–1790
Biffi CA, Previtali B (2008) Spatter reduction during titanium microdrilling using pulsed fiber laser. Proceedings of ICALEO 27–36
Biffi CA, Lecis N, Previtali B, Vedani M, Vimercati G (2010) Fiber laser microdrilling and its effect on material microstructure. Int J Adv Manuf Tech 983–994
Lei H, Yi Z, Chenglong M (2009) Technological study of laser cutting silicon steel controlled by rotating gas flow. Optic Laser Tech 41:328–333
Montgomery DC (2000) Design and analysis of experiments, 5th edn. Wiley, New York
Rodden WSO, Kudesia SS, Hand DP, Jones JDS (2001) Use of “assist” gas in the laser drilling of titanium. J Laser Appl 13(5):204–208
Ancona A, Röser F, Rademaker K, Limpert J, Nolte S, Tünnermann A (2008) High speed laser drilling of metals using a high repetition rate, high average power ultrafast fiber CPA system. Opt Express 16:8958–8968
Bandyopadhyay S, Gokhale H, Sarin Sundar JK, Sundararaian G, Joshi SV (2005) A statistical approach to determine process parameter impact in Nd:YAG laser drilling of IN718 and Ti-6Al-4V sheets. Opt Lasers Eng 43:163–182
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Biffi, C.A., Previtali, B. Spatter reduction in nanosecond fibre laser drilling using an innovative nozzle. Int J Adv Manuf Technol 66, 1231–1245 (2013). https://doi.org/10.1007/s00170-012-4402-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-012-4402-y