Abstract
An optimization study on the parameters of titanium nitride coating on aerospace Al7075-T6 alloy, using magnetron sputtering technique is presented. The effects of the temperature, DC bias voltage, rate of nitrogen, and DC power on the surface hardness, adhesion, surface roughness, and microstructure of the coated samples are investigated. Taguchi optimization method is used with the orthogonal array of L16 (44). However, to obtain the most optimum parameters for the best surface hardness, adhesion, and surface roughness, the signal to noise (S/N) response analysis method is implemented. Finally, the confirmation tests were carried out to show the improvement using the best parameters combination obtained from the optimization process. The improvement of 14 % in surface hardness, 4.15 % in adhesion, and 9.43 % in surface roughness are achieved.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Godja N, Kiss N, Löcker Ch, Schindel A, Gavrilovic A, Wosik J, Mann R, Wendrinsky J, Merstallinger A, Naure GE (2010) Preparation and characterization of spark-anodized Al-alloys: physical, chemical and tribological properties. Tribol Int 43:1253–1261
Sadeler R, Atasoy S, Arici A, Totic Y (2009) The fretting fatigue of commercial hard anodized aluminum alloys. J Mater Eng Perform 1282(18(9))
Majzoobi GH, Jaleh M (2007) Duplex surface treatment on AL7075-T6 alloy against fretting fatigue behavior by application of titanium coating plus nitriding. Mater Sci Eng, A 452–453:673–681
Arzamasow BN, Babich SG, Kirichenko LG, Knyazheva VM, Silaeva VI, Soloveva TV (1994) Properties of aluminum alloys with titanium nitride coating. Met Sci Heat Treat 36(6):308–312. doi:10.1007/BFO1401073
Efeoglu I, Celik A (2011) Mechanical and structural properties of AISI 8620 steel TiN coated, nitride and TiNcoated + nitride. Mater Charact 46:311–316
Subramanian B, Jayachandran M (2007) Characterization of reactive magnetron sputtered nanocrystalline titanium nitride (TiN) thin films with brush plated Ni interlayer. J Appl Electrochem 37:1069–1075
Hsieh JH, Liang C, Yu CH, Wu W (1998) Deposition and characterization of TiAlN and multi-layered TiN/TiAlN coatings using unbalanced magnetron sputtering. Surf Coat Technol 108–109:132–137
Huang JH, Lau KW, Yu GP (2005) Effect of nitrogen flow rate on structure and properties of nanocrystalline TiN thin films produced by unbalanced magnetron sputtering. Surf Coat Technol 191:17–24
Budinski KG (1988) Surface engineering for wear resistance. Prentice Hall, Englewood Cliffs, New Jersey
Mayrhofer PH, Kunc F, Musil J, Mitterer C (2002) A comparative study on reactive and non-reactive unbalanced magnetron sputter deposition of TiN coatings. Thin Solid Films 415:151–159
Diesselberg M, Stock HR, Mayr P (2004) Corrosion protection of magnetron sputtered TiNcoatings deposited on high strength aluminium alloys. Surf Coat Technol 177–178:399–403
Kelly PJ, Arnell RD (2000) Magnetron sputtering: a review of recent developments and applications. Vacuum 56:159–172
Tan CW, Miao J (2009) Optimization of sputtered Cr/Au thin film for diaphragm-based MEMS applications. Thin Solid Films 517:4921–4925
Li JF, Liao H, Normand B, Cordier C, Maurin G, Foct J, Coddet C (2003) Uniform design method for optimization of process parameters of plasma sprayed TiN coatings. Surf Coat Technol 176:1–13
Logothetidis S, Alexandrou I, Kokkou S (1996) Optimization of TiN thin film growth with in situ monitoring: the effect of bias voltage and nitrogen flow rate. Surf Coat Technol 80:66–71
Farooq M, Lee ZH (2002) Optimization of the sputtering process for depositing composite thin films. J Korean Phys Soc 40(3):511–515
Mayrhofer PH, Mitterer C, Musil J (2003) Structure–property relationship in single- and dual-phase nanocrystalline hard coatings. Surf Coat Technol 174–175:725–731
Ghani JA, Choudhury IA, Hassan HH (2004) Application of Taguchi method in the optimization of end milling parameters. J Mater Process Technol 145:84–92
Chunyan Y, Linhai T, Yinghui W, Shebin W, Tianbao L, Bingshe X (2009) The effect of substrate bias voltages on impact resistance of CrAlN coatings deposited by modified ion beam enhanced magnetron sputtering. Surf Sci 255:4033–4038
Mubarak A, Hamzah E, Toff MRM (2006) Influence of nitrogen gas flow rate on the Microstructural and mechanical properties of TiN deposited carbon steel synthesized by CAE Pvd technique. AJSTD 23(4):239–251
Panich N, Wangyao P, Hannongbua S, Sricharoenchai P, Sun Y (2007) Effect of argon-nitrogen mixing gas during magnetron sputtering on titanium interlayer deposition with TiB2 coatings on high speed steel. Rev Adv Mater Sci 16:80–87
Gangopadhyay S, Acharya R, Chattopadhyay AK, Paul S (2010) Effect of substrate bias voltage on structural and mechanical properties of pulsed DC magnetron sputtered TiN–MoSx composite coatings. Vacuum 84:843–850
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zalnezhad, E., Sarhan, A.A.D. & Hamdi, M. Optimizing the PVD TiN thin film coating’s parameters on aerospace AL7075-T6 alloy for higher coating hardness and adhesion with better tribological properties of the coating surface. Int J Adv Manuf Technol 64, 281–290 (2013). https://doi.org/10.1007/s00170-012-4022-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-012-4022-6