Abstract
Inconel 718 has high strength, which makes it difficult to cut using conventional cutting methods. In the present study, the laser inert gas cutting of Inconel 718 was simulated by finite element analysis software ANSYS. Finite element method was used to predict thermal stress and kerf width formation during the laser cutting process. ANSYS Parameter Design Language was used to model the Gaussian-distributed heat flux from the laser beam acting on the workpiece. The removal of melted material during laser cutting to form the kerf width was modeled by employing the element death methodology in ANSYS. In addition, laser cutting was simulated at continuous wave (CW) and the effects of laser power and cutting speed on kerf width were investigated. A series of experiments were carried out to verify the predictions. The temperature fields on the workpiece were measured using thermocouples. The kerf width size was measured using a profile projector, whereas the metallurgical and morphological changes at the cutting edge were examined using scanning electron microscopy. A good correlation was found between the simulation and experimental results.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Arif AFM, Yilbas BS (2008) Thermal stress developed during laser cutting process: consideration of different materials. Int J Adv Manuf Technol 37:698–704
Steen WM (1991) Laser material processing. Springer, London, pp 72–80
Prusa JM, Venkitachalam G, Molian PA (1999) Estimation of heat conduction losses in laser cutting. Int J Mach Tools Manuf 39:431–458
Zhong Ji, Shichun Wu (1998) FEM simulation of the temperature field during laser forming of sheet metal. J Mater Process Technol 74:89–95
Ho CY, Wen MY, Ho JE, Chen DY (2007) Temperature history for cutting ceramics preheated by a CO2 laser. J Mater Process Technol 192–193:525–531
Sheng PS, Joshi VS (1995) Analysis of heat-affected zone formation for laser cutting of stainless steel. J Mater Process Technol 53:879–892
Meung Jung Kim (2005) 3D finite element analysis of evaporative laser cutting. Appl Math Model 29:938–954
Akarapu R, Li BQ, Segall A (2004) A thermal stress and failure model for laser cutting and forming operations. J Fail Anal Prev 5:51–62
Chen M-F, Wang Y-H, Hsiao W-T (2009) Finite element analysis and verification of laser marking on eggshell. J Mater Process Technol 209:470–476
Sundar M, Mativenga PT, Li L, Crouse PL (2009) Laser removal of TiN from coated carbide substrate. Int J Adv Manuf Technol 45:1169–1178
Yilbas BS, Arif AFM (2008) Modelling of residual stresses during laser cutting of small-diameter holes. Proc Instn Mech Engrs Part B: J Eng Manuf 222(12):1577–1587
Yilbas BS, Arif AFM, Abdul Aleen BJ (2009) Laser cutting of large-aspect-ratio rectangular blanks in thick sheet metal: thermal stress analysis. Proc Instn Mech Engrs, Part B: J Eng Manuf 223(1):063–071
Arif AFM, Yilbas BS, Abdul Aleem BJ (2008) Laser cutting of thick sheet metals: residual stress analysis. Opt Laser Technol 41:224–232
Yilbas BS, Arif AFM, Abdul Aleen BJ (2009) Laser cutting of holes in thick sheet metals: development of stress field. Opt Laser Technol 47:909–916
Yilbas BS, Arif AFM, Abdul Aleen BJ (2010) Laser cutting of sharp edge: thermal stress analysis. Opt Laser Technol 48:10–19
Bahotre NB, Harimkar SP (2008) Laser fabrication and machining of materials. Springer, New York, pp. 51–52, 186–187
Ion JC (2005) Laser processing of engineering materials. Elsevier, Oxford, pp 168–169
Sainte-Catherine C, Jeandin M, Kechemair D, Ricaud J-P, Sabatier L (1991) Study of dynamic absorptivity at 10.6 μm (CO2) and 1.06 μm (Nd–YAG) wavelengths as a function of temperature. J De Physique IV C7:151–157
Radovanovic M (2006) Some possibilities for determining cutting data when using laser cutting. J Mech Eng 52:645–652
Theory reference for ANSYS, ANSYS Release 10.0, ANSYS, Inc., USA
Yilbas BS (2004) Laser cutting quality assessment and thermal efficiency analysis. J Mater Process Technol 155–156:2106–2115
Yilbas BS, Arif AFM, Abdul Aleem BJ (2010) Laser cutting of rectangular blanks in thick sheet metal: effect of cutting speed on thermal stresses. J Mater Eng Perform 19:177–184
Special metals [Online]. Available from http://www.specialmetals.com/documents/Inconelalloy718.pdf. Accessed 12th May 2009
Anderson M, Patwa R, Yung CS (2006) Laser-assisted machining of Inconel 718 with an economic analysis. Int J Mach Tools Manuf 46:1879–1891
Acknowledgments
The authors acknowledge the Universiti Sains Malaysia Science Fund project grant no. 6013362 provided by the Ministry of Science, Technology, and Innovation, Malaysia and USM-RU-PRGS project grant no. 8031011 from Universiti Sains Malaysia.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Nyon, K.Y., Nyeoh, C.Y., Mokhtar, M. et al. Finite element analysis of laser inert gas cutting on Inconel 718. Int J Adv Manuf Technol 60, 995–1007 (2012). https://doi.org/10.1007/s00170-011-3655-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-011-3655-1