Abstract
The paper reports the latest outcomes of using design-based reverse engineering on turbine blades. For a long time, the focus of the reverse engineering methods has been the trend toward higher accuracies and faster measurements. Authors introduce a different viewpoint which focuses on design intent of a part. How to reverse engineer a complex shape like a turbine blade is the subject of current research. The attempt toward taking advantage of the construction geometry behind a sample heavy duty turbine blade is thoroughly discussed in three phases. First phase consists of 2D analysis of the reference sections. Then, the stacking axis is introduced as an important non-tangible feature which has the main role to connect the sections in 3D in lean and tilt directions. The third phase uses the concept of blade twist to provide a constraint to define rotational position of the sections with respect to neighbor sections. All the three phases have been applied to different types of original and non-original products which are available in the gas turbine market. The presented comparisons show clearly that the new method of reverse engineering incorporating construction geometry and design intent of the part is quite useful and recognizes many features behind the external geometry which is impossible to follow by the previous conventional methods. The turbine blade 3D model resulted from this new method will have a smooth arc-based surface, straight stacking line passing through turbine axis with maximum section tilt of 0.2 mm and maximum section lean of 0.3 mm to original equipment manufacturer parts and linearly increasing stagger angle from hub to tip which are some of considerable improvements compared to conventional method.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Varady T, Martin RR, Cox J (1997) Editorial special issue: reverse engineering of geometric models. Comput Aided Des 29(4):253–254
Langbein FC (2003) Beautification of reverse engineered geometric models. PhD Thesis. Dept. of Computer Science, Cardiff University
Wolovich W, Albakri H, Yalcin H (2002) The precise measurement of freeform surfaces. Trans of ASME: J Manuf Sci Eng 124:326–332
Huang J, Menq CH (2001) Automatic data segmentation for geometric feature extraction from unorganized 3-D coordinate points. IEEE Trans on Robotics and Automation, V17, No. 3:268–279
Chen LC, Lin GCI (2000) Reverse engineering in the design of turbine blades – a case study in applying the MAMDP. Robot Cim-Int Manuf 16:161–167
Tai CC, Huang MC (2000) The processing of data points basing on design intent in reverse engineering. Int J Mach Tool Manuf 40:1913–1927
Thompson WB, Owen JC (1999) Feature-based reverse engineering of mechanical parts. IEEE T Robotic Autom 15(1):120–125
Mills BI, Langbein FC, Marshall AD, Martin RR (2001) Estimate of frequencies of geometric regularities for use in reverse engineering of simple mechanical components. Internal Technical Report GVG 2001–1, Computational Geometry and Computer Vision Group, Dept. of Computer Science, Cardiff University, http://ralph.cs.cf.ac.uk/papers/Geometry/survey.pdf
Huang J, Menq CH (2002) Combinatorial manifold mesh reconstruction and optimization from unorganized points with arbitrary topology. Comput Aided Des 34:149–165
Li Y, Huang X, Gong C, Wang K (2004) An engineering rules based parameterization approach for turbine blade reverse engineering. Geom Model Process 2004:311
Werghi N, Fisher R (1999) Object reconstruction by incorporating geometric constraints in reverse engineering. Comput Aided Des 31:363–399
Benko P, Varady T (2002) Constrained fitting in reverse engineering. Comput Aided Geom Des 19:173–205
Fisher RB (2004) Applying knowledge to reverse engineering problems. Comput Aided Des 36:501–510
Mohaghegh K, Sadeghi MH, Abdullah A (2007) Reverse engineering of turbine blades based on design intent. Int J Adv Manuf Tech 32:1009–1020
Society of Automotive Engineers (1996) Airfoil shapes: dimensioning of turbine engine, aeronautical recommended practice ARP 265A. Society of Automotive Engineers, New York
FEP International Private Ltd (1980) Investment casting handbook. FEP, Punjab, pp 205–210
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Mohaghegh, K., Sadeghi, M.H., Abdullah, A. et al. Improvement of reverse-engineered turbine blades using construction geometry. Int J Adv Manuf Technol 49, 675–687 (2010). https://doi.org/10.1007/s00170-009-2409-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-009-2409-9