Abstract
The conventional fusion welding of magnesium alloys often produces porosity in the weld joint, which deteriorates its mechanical properties. To solve this problem, friction stir welding (FSW), a solid-state welding technique, can be applied for joining of magnesium alloys. In this investigation, an attempt was made to understand the effect of FSW process parameters such as tool rotational speed, welding speed, and axial force on tensile properties of AZ31B magnesium alloy. Fourteen joints were fabricated using different levels of tool rotational speed, welding speed, and axial force. Tensile properties of the welded joints were evaluated and correlated with the weld zone microstructure and hardness. From this investigation, it is found that the joints fabricated using a tool rotational speed of 1,600 rpm, a welding speed of 0.67 mm/s, and an axial force of 3 kN yielded superior tensile properties compared to other joints. Optimum level of heat generation, formation of finer grains, and higher hardness are the main reasons for the superior tensile properties of these joints. Fatigue properties of FSW joints were evaluated, and it was found that fatigue properties of FSW joints were slightly lower than the base metal.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Mordike BL, Ebert T (2001) Magnesium—properties, applications. Potential Mater Sci Eng A 302:37–45
Munitz A, Cotler C, Stern A, Kohn G (2001) Mechanical properties and microstructure of gas tungsten arc welded magnesium AZ91D plates. Mater Sci Eng A 302:68–73
Magnesium and magnesium alloy (1999) ASM Specialty Hand book, ASM International, pp 194–199
Afrin N, Chen DL, Cao X, Jahazi M (2008) Microstructure and tensile properties of friction stir welded AZ31B magnesium alloy. Mater Sci Eng A 472:179–186
Lee WB, Yeon YM, Jung SB (2003) Joint properties of friction stir welded AZ31B–H24 magnesium alloy. Mater Sci Techno 19:785–790
Wang XH, Wang KS (2006) Microstructure and properties of friction stir butt-welded AZ31 magnesium alloy. Mater Sci Eng A 431:114–117
Esparza JA, Davis WC, Trillo EA, Murr LE (2002) Friction stir welding of magnesium alloy AZ31B. J Mater Sci Lett 21:917
Zhang H, Lin SB, Feng JC, Ma ShL (2006) Defects formation procedure and mathematic model for defect free friction stir welding of magnesium alloy. Mater Des 27:805–809
Abbasi Gharacheh M, Kokabi AH, Daneshi GH, Shalchi B, Sarrafi R (2006) The influence of the ratio of “rotational speed/traverse speed” (ω/v) on mechanical properties of AZ31 friction stir welds. Int J Mach Tool Manu 46:1983–1987
Pareek M, Polar A, Rumiche F, Indacochea JE (2007) Metallurgical evaluation of AZ31B–H24 magnesium alloy friction stir welds. Mater Eng Perform 16(5):655–662
Hua Z, Huiqiang WU, Jihua H, Sanbao WN, Lin WU (2007) Effect of welding speed on the material flow patterns in friction stir welding of AZ31 magnesium alloy. Rare Met 26:158–162
Cao X, Jahazi M (2008) Effect of welding speed on the quality of friction stir welded butt joints of a magnesium alloy. Mater Des. doi:10.1016/j.matdes.2008.08.040
Dieter GE (1988) Mechanical metallurgy. Tata McGraw Hill, New York
Sonsino CM (1999) Fatigue assessment of welded joints in Al-Mg-4.5 Mn aluminium alloy AA 5083 by local approaches. Inter J Fat 21:985–999
Courtney TH (2000) Mechanical behaviour of materials, 4th edn. McGraw Hill, New York
Buffa G, Hua J, Shivpuri R, Fratini L (2006) Design of the friction stir welding tool using the continuum based FEM model. Mater Sci Eng A 419:389–396
Lee WB (2004) Mechanical properties related to microstructural variation of 6061 al alloy joints by friction stir welding. Mater Trans 45(5):1700–1705
Lee WB, Yeon YM, Jung S-B (2003) The joint properties of dissimilar formed Al alloys by friction stir welding according to the fixed location of materials. Script Mater 49:423–428
Fonda RW, Lambrakos SG (2002) Analysis of friction stir welds using an inverse problem approach. Sci Tech Weld Join 7(3):177–181
Zhang HW, Zhang Z, Chen JT (2005) The finite element simulation of the friction stir welding process. Metall and Mater Trans A 403:305–316
Heurtier P, Jones MJ, Desrayaud C, Driver JH, Montheillet F, Allehaux D (2006) Mechanical and thermal modelling of friction stir welding. J Mater Process Technol 171:348–357
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Padmanaban, G., Balasubramanian, V. An experimental investigation on friction stir welding of AZ31B magnesium alloy. Int J Adv Manuf Technol 49, 111–121 (2010). https://doi.org/10.1007/s00170-009-2368-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-009-2368-1