Abstract
During high-speed machining Ti-6Al-4V alloy, high-temperature at the tool–chip interface and the concentration gradient of chemical species between tool material and workpiece material support the activation of diffusion process, and therefore the crater wear forms on the rake surface of the cutting tool at a short distance from the cutting edge. In this paper, the diffusion analysis was theoretically proposed. The constituent diffusion at the contact interface between tool material and Ti-6Al-4V alloy at high-temperature environment, the crater wear on the rake surface of the tool, and the chips collected from high-speed milling Ti-6Al-4V alloy with straight tungsten carbide tools were analyzed by the scanning electron microscope with energy dispersive X-ray spectroscopy. The constituents inside the tool could diffuse into the workpiece and the diffusion layer was very thin and close to the interface. Compared with the diffusion of tungsten and carbon atoms, the pulling out and removing of the tungsten carbide (WC) particles due to cobalt diffusion dominated the crater wear mechanism on the rake surface of the cutting tool.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Amin AKMN, Ismail AF, Khairusshima MKN (2007) Effectviness of uncoated WC-Co and PCD inserts in end milling of titanium alloy—Ti-6Al-4V. J Mater Proc Tech 192–193:147–158. doi:10.1016/j.jmatprotec.2007.04.095
Rahman M, Wang ZG, Wong YS (2006) A review on high-speed machining of titanium alloys. JSME Int J C 49(1):11–20. doi:10.1299/jsmec.49.11
Li JCM (2000) Microstructure and properties of materials (Volume 2). World Scientific, Singapore
Rahim EA, Sharif S (2006) Investigation on tool life and surface integrity when drilling Ti-6Al-4V and Ti-5Al-4V-Mo/Fe. JSME Int J C 49(2):340–345. doi:10.1299/jsmec.49.340
Venugopal KA, Paul S, Chattopadhyay AB (2007) Growth of tool wear in turning of Ti-6Al-4V alloy under cryogenic cooling. Wear 262:1071–1078. doi:10.1016/j.wear.2006.11.010
Ezugwu EO, Wang ZM (1997) Titanium alloy and their machinability—a review. J Mater Proc Tech 68:262–274. doi:10.1016/S0924-0136(96)00030-1
Corduan N, Hirnbert T, Poulachon G et al (2003) Wear mechanisms of new tool materials for TiBAI4V high perfonnance machining. CIRP Ann 52(1):73–76. doi:10.1016/S0007-8506(07)60534-4
Zoya ZA, Krishnamurthy R (2000) The performance of CBN tools in the machining of titanium alloys. J Mater Proc Tech 100(1–3):80–86. doi:10.1016/S0924-0136(99)00464-1
Loladze TN (1962) Adhesion and diffusion wear in metal cutting, mechanical engineering division, in: Proceedings of the 42nd Annual Convention, Calcutta, West Bengal, pp 108–141
Loladze TN (1981) On the theory of diffusion wear. CIRP Ann 30(1):71–76. doi:10.1016/S0007-8506(07)60898-1
Naerheim Y, Trent EM (1977) Diffusion wear of cemented carbide tools when cutting steel at high speed. Met Technol 4(12):548–555
Trent EM (1991) Metal cutting (third edn). Butterworth-Heinemann, London
Molinari A, Nouari M (2002) Modeling of tool wear by diffusion in metal cutting. Wear 252:135–149. doi:10.1016/S0043-1648(01)00858-4
Nouari M, Molinari A (2005) Experimental verification of a diffusion tool wear model using a 42CrMo4 steel with an uncoated cemented tungsten carbide at various cutting speeds. Wear 259:1151–1159. doi:10.1016/j.wear.2005.02.081
Jiang H, Shivpuri R (2005) A cobalt diffusion based model for predicting crater wear of carbide tools in machining titanium alloys. J Eng Mater Technol 127(1):136–144. doi:10.1115/1.1839192
Dearnly PA, Grearson AN (1986) Evaluation of principal wear mechanisms of cemented carbides and ceramics used for machining titanium alloy IMI 318. Mat Sci Tech 2:47–58
Nabbani F (2001) Wear mechanisms of ultra hard cutting tool materials. J Mater Proc Tech 115:402–412. doi:10.1016/S0924-0136(01)00851-2
Jawaid A, Sharif S, Koksal S (2000) Evaluation of wear mechanism of coated tools when face milling titanium alloy. J Mater Proc Tech 99:266–274. doi:10.1016/S0924-0136(99)00438-0
Childs T, Maekawa K, Obikawa T, Yamane Y (2000) Metal machining theory and applications. Wiley, New York
Cheng J, Wu Y, Yu Q (2001) Cutting performance and mechanism of RE carbide tools. Rare Met 20(3):197–201
Su Y, He N, Li L, Li XL (2006) An experimental investigation of effects of cooling/lubrication conditions on tool wear in high-speed end milling of Ti-6Al-4V. Wear 261:760–766. doi:10.1016/j.wear.2006.01.013
Bäker M, Rösler J, Siemers C (2003) The influence of plastic properties on chip formation. Comput Mater Sci 26:175–182. doi:10.1016/S0927-0256(02)00396-8
Hughes JI, Sharman ARC, Ridgway K (2006) The effect of cutting tool material and edge geometry on tool life and workpiece surface integrity. J Eng Manuf 220:93–107
Shewmon PG (1963) Diffusion in solids. McGraw-Hill, New York
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhang, S., Li, J.F., Deng, J.X. et al. Investigation on diffusion wear during high-speed machining Ti-6Al-4V alloy with straight tungsten carbide tools. Int J Adv Manuf Technol 44, 17–25 (2009). https://doi.org/10.1007/s00170-008-1803-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-008-1803-z