Abstract
In the current metal forming product development paradigm, the simultaneous and optimal design of product, process and forming system is a non-trivial issue as there are many affecting factors which interact and interplay each other. In the up-front design process, the systematic evaluation and verification of design solution is critical as this could shift the product development paradigm from traditionally trial-and-error and heuristic know-how to more scientific calculation, analysis and simulation. To ensure the efficient and accurate assessment and evaluation of design solution generation, state-of-the-art technologies need to be developed. In this paper, a methodology for systematic evaluation and verification of the simultaneous design of metal forming product, process, and forming system is presented. The factors which affect these designs are first articulated and how they interact and interplay are described. The importance of the systematic evaluation of designs is, thus, figured out. In addition, the role that CAE simulation plays in this process is explained. To evaluate the design, detailed evaluation criteria are developed and how the criteria are used through CAE simulation technology to reveal the behaviors and performances of designs is articulated. Through case studies, the developed technology is illustrated and its efficiency is finally verified.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Fuh JYH, Zhang YF, Nee AYC, Fu MW (2004) Computer-aided injection mould design and manufacture. Marcel Dekker, Inc., New York
Kobayashi S, Oh SI, Altan T (1989) Metal Forming and the Finite-element Method. Oxford University Press, Oxford
Bariani PF, Negro TD, Bruschi S (2004) Testing and modeling of material response to deformation in bulk metal forming. Annals of the CIRP 53(2)
Fu MW, Yong MS, Tong KK, Muramatsu T (2006) A methodology for evaluation of metal forming system design and performance via CAE simulation. Int J Prod Res 44:1075–1092
Tong KK, Yong MS, Fu MW, Muramatsu T, Goh CS, Zhang SX (2005) A CAE enabled methodology for die fatigue life analysis and improvement. Int J Prod Res 43:131–146
Fu MW, Yong MS, Muramatsu T (2007) Die fatigue life design and assessment via CAE simulation. Int J Adv Manuf Technol, on-line
Fu MW, Yong MS, Tong KK, Wong CC (2005) CAE supported design solution generation in metal forming product development. Trans of the NAMRC 33:375–382
Lange K, Cser L, Geiger M, Kals JAG (1992) Tool life and tool quality in bulk metal forming. Annals pf the CIRP 41(2):667–675
Jirathearanat S, Hartl C, Altan T (2004) Hydroforming of Y-shapes-product and process design using FEA simulation and experiments. J Mat Proc Tech 146(1):124–129
Geiger M, Merklein M, Kerausch M (2004) Finite element simulation of deep drawing of tailored heat treated blanks. CIRP Annals 53(2):223–226
Petty DM (1996) Application of process modeling-an industrial view. J Mat Proc Tech 60:421–426
Bariani PF, Bruschi S, Dal NT (2004) Integrating physical and numerical simulation techniques to design the hot forging process of stainless steel turbine blades. Int J of Machine Tools and Manufacture 44(9):945–951
Falk B, Engel U, Geiger M (1998) Estimation of tool life in bulk metal forming based on different failure concepts. J Mat Proc Tech 80–81:602–607
Mungi MP, Rasane SD, Dixit PM (2003) Residual stresses in cold axisymmetric forging. J Mat Proc Tech 142:256–266
MacCormack C, Monagham J (2001) Failure analysis of cold forging dies using FEA. J Mat Proc Tech 117:209–215
Fu MW, Luo ZJ (1992) The prediction of macro-defects during the isothermal forging process by the rigid-viscoplastic Finite-Element Method. J Mat Proc Tech 32:99–608
Fu MW, Luo ZJ (1995) The simulation of the visco-plastic forming process by the Finite-Element Method. J Mat Proc Tech 55:442–447
Cho H, Ngaile G, Altan T (2003) Simultaneous determination of flow stress and interface friction by finite element based inverse analysis technique. Annals of CIRP 52:221–224
Mamalis AG, Johnson W (1987) Defects in the processing of metals and composites. In: Predeleanu M (ed) Computational methods for predicting material processing defects. Elsevier, Amsterdam
Gelin JC, Oudin J, Ravalard Y (1985) An improved finite element method for the analysis of damage and ductile fracture in cold forming processes. Annals of the CIRP 34:209–212
Reddy NV, Dixit PM, Lal GK (1996) Central bursting and optimal die profile for axisymmetric extrusion. J Manuf Sci Eng 118:579–566
Clift SE, Hartley P, Sturgess CEN, Rowe GW (1990) Fracture prediction in plastic deformation processes. Int J Mech Sci 32:1–17
NV Reddy, PM Dixit, Lal GK (2000) Ductile fracture criteria and its prediction in axisymmetric drawing. Int J Mach Tools Manuf 40:95–111
Gouveia BPPA, Rodrigues JMC, Martins PAF (1996) Fracture predicting in bulk metal forming. Int J Mech Sci 38:361–372
S Gupta, NV Reddy, PM Dixit (2003) Ductile fracture prediction in axisymmetric upsetting using continuum damage mechanics. J Mater Process Technol 141:256–265
Scientific forming Technologies Corporation (2007) DEFORM™ 3D v6.01 User’s Manual
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Fu, M.W., Yong, M.S., Tong, K.K. et al. Design solution evaluation for metal forming product development. Int J Adv Manuf Technol 38, 249–257 (2008). https://doi.org/10.1007/s00170-007-1091-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-007-1091-z