Abstract
The capability to build parts with predetermined porous microstructure and dense walls using powdered biomaterials makes selective laser sintering (SLS), one of the more flexible rapid prototyping (RP) process, a strong candidate for building biodegradable controlled release drug delivery devices (DDD). The objective is to design a varying-porosity circular disc with outer region being denser acting as diffusion barrier region and inner more porous region acting as drug encapsulation region. This is to achieve a zero-order of release over a desired duration of time in drug administration.
A key study in this paper was to determine the influence of critical SLS process parameters namely, laser power, laser scan speed and part bed temperature on dense wall formation and control of the porous microstructure of SLS-fabricated parts built with biomaterials. The physical characteristics of the fabricated devices were investigated through microstructure examination using the scanning electron microscope (SEM). Two biodegradable polymers, namely Polycaprolactone (PCL) and Poly (-L) Lactic Acid (PLLA), were investigated. For PCL varying-porosity disc, the laser power is set at 3 W (inner region) - 4 W (outer region), the scan speed at 5080 mm/s and the part bed temperature at 40°C. For Poly(-L) Lactic Acid (PLLA), the laser power is set at 12 W, the scan speed at 1270 mm/s and the part bed temperature at 60°C. With the set of SLS parameters tabulated for specific polymers, polymeric matrix with specific porosity can be fabricated as drug delivery devices.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Maekawa K (2002) Three-Dimensional Powder Fabrication by Laser Sintering. Proc. 2nd Intl. Conf. on Rapid Proto. & Manuf., Beijing, pp. 304–313
Brannon-Peppas L (1997) Polymers in controlled drug delivery, Med. Plast. Biomat. Nov:34–45
Cheah C.M., Leong K.F., Chua C.K., Low K.H. and Quek H.S., (2002) Characterization of microfeatures in selective laser sintered drug delivery devices. Proc Inst Mech Eng Part H: J Eng in Med 216(6):369–383
Nelson JC (1993) Selective laser sintering: a definition of the process and an empirical sintering model. Ph.D Distn., Uni. Texas Aus., USA
Chua CK, Leong KF, Lim CS (2003) Rapid Prototyping: Principles and Applications. World Scientific, Singapore
Solvay Caprolactones, (2003) CAPA(r) 6501 Polycaprolactone, Matl. Safety Data Sheet
Dickens E.D., Lin L.B., Taylor G.A., Magistro A.J. and Ng H., (1994) Sinterable Semi-Crystalline Powder and Near Fully Dense Article Formed Therewith, US Pat. No. 5342919
DTM( Corporation, (2000) The Sinterstation® System, Guide to Matls: DuraForm Polyamide.
Bershtein VA, Egorov VM (1994) Differential Scanning Calorimetry of Polymers: Physics, Chemistry, Analysis, Technology. Ellis Horwood, London
Ma PX, Choi JW (2001) Biodegradable Polymer Scaffolds with Well-Defined Spherical Pore Network. Tissue Eng 7(1):23–33
Mainchent P, Perez MH, Zinutti C, Lamprecht A, Ubrich N, Astier A, Hoffman M, Bodmeier R (2000) The Preparation and Evaluation of Poly(ɛ-caprolactone) Microparticles Containing Both a Lipophilic and a Hydrophilic Drug. J Ctrl Rel 65:429–438
Ku JCW (2002) Studies of Selective Laser Sintering Components with Controlled Porosity. M(Phil) Ths., Uni. Hong Kong, Hong Kong
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Leong, K.F., Chua, C.K., Gui, W.S. et al. Building Porous Biopolymeric Microstructures for Controlled Drug Delivery Devices Using Selective Laser Sintering. Int J Adv Manuf Technol 31, 483–489 (2006). https://doi.org/10.1007/s00170-005-0217-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-005-0217-4