Abstract
In the present study, the mechanical properties of geopolymer concrete (GPC) has been investigated. GPC represents a novel technology that is giving significant concern in industrial construction, especially in term of the current emphasis on sustainability. In this study, the NaOH and Na2SiO3 solutions were used as an alkaline solution in all GPC mixes. Na2SiO3 with 10 concentration of molarity, activator-to-FA ratio of 0.4, Na2SiO3/NaOH ratio of 1.75, and two curing regimes viz., ambient curing, and heat curing at 75 °C for 26 h were employed. The experimental results indicated that the geopolymer concrete strengths, modulus of elasticity, and other mechanical properties increased with heat curing as compared to ambient temperature curing. The elastic modulus of GPC was associated with the compressive strengths and similar to those of OPC concrete. Furthermore, the geopolymer concrete mixture requires proper mix proportion and temperature-controlled curing conditions to accomplish good results.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
The manufacture of ordinary Portland cement (OPC) contributes about 10% of CO2 emission to the environment and because of a significant demand for construction in various sector of industries such as, buildings, transportation, dams, tunnels, and sewage, etc., there is an urgent need for an alternate material binder which can replace OPC for a cleaner and sustainable construction [1,2,3,4,5,6]. Geopolymer materials are a novel construction technology that could be employed for green construction purposes [7,8,9]. There are two significant ingredients of geopolymer concrete, namely the source material with rich Alumina–Silica content such as fly ash (FA), metakaolin or GGBFS), and alkali activator, which consists of sodium silicate and sodium hydroxide solutions [10,11,12,13]. The raw material which is rich in Aluminium (Al) and silica (Si) such as GGBFS, fly ash, or metakaolin reacts with an alkaline solution to produce alumina silicate gel [14,15,16]. This gel behaves as a binder which binds unreacted materials (sand and coarse aggregates) to manufacture geopolymer concrete (GPC) [17].
The geopolymer concrete is considered as an ideal choice not only because it is a sustainable material, but because it utilizes waste materials from industries as a source material contrast OPC which uses virgin materials [9, 18].
Although usage of geopolymer concrete is still in the beginning stage, however, recently, many structures have been successfully constructed utilizing geopolymer concrete [19]. Some of these geopolymer composites are reinforced box culverts, concrete pipes, pavements, structural elements, precast concrete such as railway sleeper and electric power pole and marine construction, reinforced box culverts, precast footway panels, the airport in southeast Queensland, Australia, etc. [20].
In the production of geopolymer concretes, fly ash is considered the primary source materials due to its availability in the industry. According to the chemical composition, fly ash is categorized as either class F or class C. The previous studies on the GPC reported that the use of F class of FA on the production of GPC has comparable or superior mechanical properties to the OPC concretes [21, 22]. In India, the manufacture of clay bricks requires 540 million tonnes of clay for manufacturing 180 billion tonnes of clay brick per year, makes 26,800 hectares of land barren, and requires 30 million tonnes of coal equivalent, generates around 27 million tonnes of CO2 [19, 23, 24]. Annually, a 10–12% replacement with fly ash will consume 30–32 million tonnes of fly ash, save coal and environment and yield a benefit of 310 crores by decrease cost in the production of blocks [24].
To fill the gap on the mechanical behaviour of GPC, long-term engineering properties of GPC such as flexural strength elastic modulus and compressive strength, in addition to the effect of types of curing (heat and ambient) have been investigated in the study. We also recommended more researches on geopolymer concrete for a better understanding of the performance behaviour of GPC before introducing this concrete to the industrial construction as an alternative to OPC concrete. The cost analysis and economic benefits of GPC and OPC concrete also have been compared to find out the economic aspect of GPC along with the environmental potentials for a clean technology option.
In the present study, the elastic modulus, EC, of geopolymer concrete was calculated at the stress level equal to 40% of cylinder compressive strength \((f_{c}^{\prime } )\). For each mixture, three concrete cylinders of 100 × 200 mm were cast.
In term of elastic modulus, the experimental values are compared with the elastic modulus calculated using the equations proposed by some researchers and equations recommended in various code standards.
Australian Standard AS3600 [25] suggests Eqs. (1) and (2) for the elastic modulus of concrete (± 20%) at the proper age.
where Ecj elastic modulus in MPa, fcmi site compressive strength (90% of cylinder strength (fcm) tested at laboratory), ρ the concrete density in kg/m3.
American Concrete Institute the ACI 318-14 code [26] recommends Eq. (3) for calculating the elastic modulus of concrete.
where ρ the density of concrete kg/m3, \(f_{c}^{\prime }\) the compressive strength of concrete after 28 days of curing in MPa, and Ec the elastic modulus in MPa.
Diaz-Loya et al. [27] suggested Eq. (4) for predicting elastic modulus of GPC depending on the experimental results of heat-cured fly ash GPC.
where Ec the elastic modulus (MPa); \(f_{c}^{\prime }\) compressive strength of heat-cured GPC after 3 days curing. For the reason that the GPC specimens cured at elevated temperature develop strength approximately equal to the ultimate strength after few days curing, the \(f_{c}^{\prime }\) in Eq. (4) indicates the ultimate strength of the GPC. Furthermore, geopolymer concrete specimens cured in normal condition (room temperature) gain strength slowly with the time [21, 28]. Lee and Lee [29] proposed Eq. (5) for predicting the elastic modulus of GPC. While Nath and Sarker [30] proposed Eq. (6) to calculate the elastic modulus of GPC.
where Ec the elastic modulus (MPa) and \(f_{c}^{\prime }\) the compressive strength of GPC.
From the values of compressive strengths, various standard codes have proposed equations to evaluate the flexural strength of concrete. In this study, the equations suggested in the American and Australian standard codes were employed to assess the flexural strength of GPC and compared with the obtained values by experimental test.
Australian Standard code The flexural strength of concrete \((f_{ct.f}^{\prime } )\) at 28 days can be computed employing Eq. (7) as proposed by AS 3600 [25].
where \(f_{c}^{\prime }\) 90% of cylinder compressive strength (fcm) prepared and tested at a laboratory.
American Concrete Institute The ACI Code 318-14 [26] suggested Eq. (8) for calculating the flexural strength of concrete using the values of compressive strength.
The relationships between the specified \((f_{c}^{\prime } )\) and measured compressive strengths (fcm) are given by Eqs. (9)–(11).
Indian standard code The IS 456-2000 code [31] recommended the following Eq. (12) for predicting the flexural strength of concrete using the compressive strength of the corresponding specimen.
where fr is the flexural strength of concrete and fck is the compressive strength at 28 days.
Diaz-Loya et al. [27] suggested the following Eq. (13) to calculate the flexural strength of geopolymer concrete based fly ash;
where fr the flexural strength of fly ash-based GPC and fc compressive strength of heat-cured GPC after 3 days.
2 Experimental details
2.1 Materials
2.1.1 Fly ash
Fly ash from Dadri thermal power station, Uttar Pradesh (U.P.), India, was utilized in this experimental investigation. The fly ash was greyish colour and comprised of 51.86% SiO2, 1.66% MgO, 1.08% K2O, 9.15% Al2O3, 33.98% Fe2O3, and 2.26% CaO, which as analysed by X-ray fluorescence (XRF). As per ASTM C618 [32], according to the chemical composition analysis, the FA had a low Ca content and classified as class F.
2.1.2 Aggregates
Limestone aggregates available on the market have a specific gravity of 2.67, and 16 mm was the maximum size of coarse aggregates used. The sand utilized in this experimental work was river sand with a specific gravity of 2.58. The fineness analysis of coarse and fine aggregates has been done according to IS 383 [28] guidelines, and the results of the fineness analysis curve were in the limitation of IS 383 [28].
2.1.3 Alkaline solution
An alkaline solution prepared by mixing the solutions of NaOH and Na2SiO3 with 10 molarity, the composition of Na2SiO3 was 15.35% Na2O, 32.85% SiO2, and 51.80% water. However, for preparing the sodium hydroxide solution, sodium hydroxide in flakes form and 10 molarity were dissolved on water, i.e., 314 grams of sodium hydroxide flakes dissolved in 1 L of water. After that, the sodium hydroxide solution was mixed with sodium silicate and then left for at least 6 h before use.
2.2 Methodology
2.2.1 Mixing proportions
The weight of coarse and fine aggregates was 70% of the total mix. For all combinations, the ratio of activator-to-FA was constant and equal to 0.4. The NaOH molarities were 10 M in all mixes, and the ratio of Na2SiO3-to-NaOH by weight was 1.75. Table 1 gives the mix proportions of GPC mixtures used in this study.
2.2.2 Mixing procedure
The mixing technique was achieved according to the guidelines reported from previous works on the geopolymer concrete [27, 29]. The process was initiated by mixing Na2SiO3 with NaOH solution for 4 min. After that, the fly ash was added to the mixer with sand and coarse aggregate and mixed for 4–6 min. Then, the alkaline solution was added to the dry materials mixture and mixed for an extra 4 min.
2.2.3 Casting of specimens
For compressive strength tests, GPC was cast into 150 mm cube moulds according to ASTM C192 [30]. For the elastic modulus test, GPC was cast into 100 × 200 mm cylindrical steel moulds. For the flexural strength test, GPC was cast into 100 × 100 × 500 mm prism moulds.
2.2.4 Curing of specimens
In this experimental work, two curing conditions were employed. The first type of curing was heat (oven) curing at 75 °C for 26 h after a 2–3 days delay time. The delay time was the time from the casting of specimens into the moulds till unmoulds the specimens. The delay time lets concrete to accomplish initial setting time before being shifted to the curing room or curing oven. The other curing condition was in ambient temperature conditions. For heat curing, all GPC specimens were moved from the oven after 26 h curing and cured in ambient temperature until testing.
3 Results and discussions
3.1 Scanning electronic microscopy test (SEM)
For a proper understanding of the microstructure of GPC, the SEM test was performed on the raw materials of GPC. Sodium silicate, fly ash, and sodium hydroxide have been tested to understand the real shape of material particles that would assist in anticipating the behaviour of the composition materials when they mixed during the production of a geopolymer binder. Figure 1a–c shows the SEM testing images of the materials used in the production of GPC. As can be seen in Fig. 1a, the fly ash material has a circular and rounded shape, while the silicon particles on the sodium silicate solution are finer than the silicon particles on the fly ash, as shown in Fig. 1b. Moreover, The SEM images of sodium hydroxide show that the particles of sodium (Na) are organized in a hydrargillite-like layer structure (Fig. 1c).
3.2 Compressive strength
The experimental results of the compressive strength of the GPC of this study are summarized in Fig. 2. The compressive strengths of GPC at 28 and 7 days were in the range of 10.50–31.11 MPa for heat curing (75 °C) while the compressive strengths of GPC at 7 and 28 days for ambient curing were 4.50–10.00 MPa for ambient curing, respectively. It can be noted that the heat curing temperature influenced the early strength of GPC due to the geopolymerisation process, which required heating for accelerating the reaction between alkali activator and fly ash. For GPC cured at 75 °C, the compressive strength increased by 57% at 7 days as compared to ambient curing. The strengths of heat-cured specimens at 28 days increased with 67% as compared to the same samples cured at room temperature. Furthermore, from Fig. 3, it can be observed that the compressive strengths of heat curing specimens of GPC were higher than the compressive strength of OPC at the age of 28 days.
Figure 4 shows the experimental test results of 7- and 28-day compressive strengths of GPC against the Na2O/FA ratio in the geopolymer concrete mixture. For both curing regimes, the maximum compressive strengths were given with approximately 12% of Na2O/FA. The compressive strength of GPC at 28 days could be expressed as a function of total moles of Na2O as given in Eqs. (14) and (15).
For 25 °C and 24 h curing
For 60 °C and 24 h curing
where \(f_{c28}^{\prime }\) the compressive strength of GPC at 28 days; MNa2O mass proportion of Na2O-to-fly ash (%).
3.3 Modulus of elasticity
The experimental results of this study have been analyzed to develop an appropriate equation using the generally utilized term, square root of compressive strength \((f_{c}^{\prime } )^{0.5}\). The analysis gave Eq. (16) for predicting the elastic modulus of GPC:
where \(f_{c}^{\prime }\) is the compressive strength of GPC in MPa. Values calculated using Eq. (16) are also presented in Fig. 5. From Fig. 5, it can be observed that Eq. (16) matches well with Eq. (4) proposed by Diaz-Loya.
The experimental results of the elastic modulus of GPC specimens and proposed Eq. (16) are presented in Fig. 5 and compared with the values calculated by previous Eqs. (1)–(6). The experimental results of elastic modulus were in the range (24 to 15 GPa). From Fig. 5, It can be concluded that the elastic modulus of GPC commonly increased with the increase of compressive strength, which that is comparable to the existing standard codes, ACI 318-14 and AS 3600 [25, 26]. The experimental results of elastic modulus of GPC are lower than those predicted using suggested equations of ACI 318-14 and AS 3600. Since the prediction equations proposed by ACI 318-14 and AS 3600 are developed for the elastic modulus of conventional concrete, some modifications on those equations are required to match the elastic modulus of GPC. The proportion between the experimental values of GPC and the values calculated as per ACI 318-14 and AS 3600 are 0.77–1.17 and 0.84–1.31, respectively, as shown in Table 2. Figure 5 shows that the equation suggested by Diaz-Loya et al. [27] matched well with the experimental findings of this investigation, while the equation presented Lee and Lee [29] drew a lower model line than the model plotted by experimental values. This variation might be attributed to the difference of the FA type, curing condition, and temperature used in those particular works and different mixture compositions and so on.
3.4 Flexural strength
The flexural strengths of geopolymer concrete were affected by the curing condition, a finding similar to those other mechanical properties where the heat curing improves the strength of geopolymer concrete. Figure 6 compares the flexural strengths of the GPC at various ages for both types of curing (oven @ 75 °C and room temperature). It can be observed that flexural strength increased when the specimen age was raised. However, the flexural strength of GPC at ambient-cured was lower than that those specimens at heat-cured. When compared with OPC concrete at 28 days, OPC concrete exhibited higher flexural strength than GPCs with 16.5% for heat-cured specimens and 60% for normal-cured samples, as shown in Fig. 7.
In Fig. 8, it can be observed that approximately all of the experimental values of this work fall in the above equations given by ACI 318-14, AS 3600, and Diaz-Loya et al. [27]. In this study, a model was developed using regression analysis by employing the experimental values. The following Eqs. (17) and (18) for heat-cured and ambient cured respectively have been proposed to fit the experimental results best, as shown in Fig. 8.
where fct.H and fct.A is the heat-cured and ambient cured flexural strengths of GPC, respectively. fc is the compressive strength of GPC (MPa). It also should be noted that the proposed Eqs. (17) and (18) give about 5–7% higher flexural strength than predicted values calculated according to the Eq. (13) that suggested by Diaz-Loya et al. [27] and 20–28% higher values than the flexural strength as per ACI Code 318-14 [26].
3.5 Cost analysis and economic benefits of GPC
A raw material cost comparison was carried out to produce GPC and OPC concrete on the assumption that the concrete producer has to buy in all raw materials from outside. The price for the reference year 2019 was requested at the terms for a significant purchaser in India. The cost estimation of the raw materials for production of GPC is presented in Table 3, and the cost estimation of the raw materials for production of OPC concrete is presented in Table 4. The significant differences between the minimum and maximum production costs for GPC and OPC concrete are shown in Fig. 9.
Despite the wide range of costs, Fig. 9 shows that, in principle, geopolymer-based concretes can be economically competitive with Portland-cement-based systems. In addition to the aggregate (sand, gravel) as the main component (approx. 75% by mass) in both mixes, the cement is the main cost driver in the OPC concrete. On the other hand, in the geopolymer concrete all components contribute to a different extent to the total costs, while, i.e. the activator sodium hydroxide contributes noteworthy to the overall costs, the solid component hard coal fly ash contributes only to a lesser extent. The activator sodium silicate solution adds with the highest specific costs considerably to the total costs.
Based on the cost analysis, it might be concluded that the cost of production of M-30, normal strength concrete, is marginally 2.9% higher than OPC concrete, whereas the cost-saving in GPC production of M-40 is 6.67% and 15.8% M-50 as compared with OPC concrete. Therefore, it can be concluded that cost-effectiveness can be achieved in the production of high strength of geopolymer concretes.
Moreover, GPC promotes early strength development, which has the potential to facilitate early project completion. Compared to traditional project construction, the project completion time can be reduced by at least 30% with the use of GPC.
4 Conclusions and remarks
Based on the analytical and experimental test results on the mechanical properties of GPC, the following remarks can be drawn.
-
Since the main constituent of GPC is an industrial by-product (fly ash), GPC is relatively inexpensive to produce. Moreover, the geopolymer binder production does not cause harmful greenhouse gas emissions and is consequently considered environmentally friendly.
-
The fresh GPC had a long setting time of 234–247 min due to the low calcium content in the matrix of GPC. The heat-curing of GPC specimens at 75 °C at the oven for 26 h enhanced the strength development. However, the strength of ambient-cured GPC continued to develop with time comparable to conventional concrete. In general, heat curing and curing temperature play a significant role in the geopolymerisation process.
-
The ratio of Na2O-to-Si2O molar has no significant effect on the compressive strength of fly ash-based geopolymer concrete.
-
SEM images enabled the assessment of reaction product formation and microstructural evolution in the specimens of GPC. The images show a less dense structure as compared with OPC concrete.
-
The elastic modulus of GPC increased when the compressive strength increased, and the equation proposed by Diaz-Loya et al. for the modulus of elasticity of fly ash-based GPC gave the best fit with elastic modulus values calculated in this study.
-
The cost-effectiveness can be achieved in the production of high strength of geopolymer concretes.
References
Habert G, D’Espinose De Lacaillerie JB, Roussel N (2011) An environmental evaluation of geopolymer based concrete production: reviewing current research trends. J Clean Prod 19:1229–1238. https://doi.org/10.1016/j.jclepro.2011.03.012
McLellan BC, Williams RP, Lay J et al (2011) Costs and carbon emissions for geopolymer pastes in comparison to ordinary portland cement. J Clean Prod. https://doi.org/10.1016/j.jclepro.2011.02.010
Zhang Z, Provis JL, Reid A, Wang H (2014) Geopolymer foam concrete: an emerging material for sustainable construction. Constr Build Mater 56:113–127
Part WK, Ramli M, Cheah CB (2016) An overview on the influence of various factors on the properties of geopolymer concrete derived from industrial byproducts. In: handbook of low carbon concrete. Elsevier, pp 263–334
Kong DLY, Sanjayan JG (2010) Effect of elevated temperatures on geopolymer paste, mortar and concrete. Cem Concr Res 40:334–339. https://doi.org/10.1016/j.cemconres.2009.10.017
Nathan AJ, Scobell A (2012) How China sees America. Foreign Aff 91:1–30
Rangan BV (2010) Fly ash-based geopolymer concrete. In: Proceedings of international workshop on geopolymer cement and concrete December 2010, pp 68–106. https://doi.org/10.1007/s10853-006-0523-8
Zhuang XY, Chen L, Komarneni S et al (2016) Fly ash-based geopolymer: clean production, properties and applications. J Clean Prod 125:253–267. https://doi.org/10.1016/j.jclepro.2016.03.019
June J, Politecnica U, Lloyd NA et al (2010) Geopolymer concrete with fly ash. In: Second international conference on sustainable construction materials and technologies
Hardjito D, Wallah SE, Sumajouw DMJ, Rangan BV (2004) On the development of fly ash-based geopolymer concrete. ACI Mater J. https://doi.org/10.14359/13485
Joseph B, Mathew G (2012) Influence of aggregate content on the behavior of fly ash based geopolymer concrete. Sci Iran. https://doi.org/10.1016/j.scient.2012.07.006
Olivia M, Nikraz H (2012) Properties of fly ash geopolymer concrete designed by Taguchi method. Mater Des. https://doi.org/10.1016/j.matdes.2011.10.036
Chindaprasirt P, Chareerat T, Sirivivatnanon V (2007) Workability and strength of coarse high calcium fly ash geopolymer. Cem Concr Compos. https://doi.org/10.1016/j.cemconcomp.2006.11.002
Allen AJ, Thomas JJ, Jennings HM (2007) Composition and density of nanoscale calcium-silicate-hydrate in cement. Nat Mater. https://doi.org/10.1038/nmat1871
Hajimohammadi A, Provis JL, Van Deventer JSJ (2011) The effect of silica availability on the mechanism of geopolymerisation. Cem Concr Res. https://doi.org/10.1016/j.cemconres.2011.02.001
Ismail I, Bernal SA, Provis JL et al (2014) Modification of phase evolution in alkali-activated blast furnace slag by the incorporation of fly ash. Cem Concr Compos. https://doi.org/10.1016/j.cemconcomp.2013.09.006
Hamouda AA, Amiri HAA (2014) Factors affecting alkaline sodium silicate gelation for in-depth reservoir profile modification. Energies. https://doi.org/10.3390/en7020568
Singh B, Ishwarya G, Gupta M, Bhattacharyya SK (2015) Geopolymer concrete: a review of some recent developments. Constr Build Mater. https://doi.org/10.1016/j.conbuildmat.2015.03.036
Hassan A, Arif M, Shariq M (2019) Use of geopolymer concrete for a cleaner and sustainable environment—a review of mechanical properties and microstructure. J Clean Prod 223:704–728. https://doi.org/10.1016/J.JCLEPRO.2019.03.051
Hassan A, Arif M, Shariq M (2019) A review of properties and behaviour of reinforced geopolymer concrete structural elements—a clean technology option for sustainable development. J Clean Prod. https://doi.org/10.1016/j.jclepro.2019.118762
Wallah SE, Rangan BV (2006) Low-calcium fly ash-based geopolymer concrete: long-term properties. Curtin University of Technology
Petermann JC, Saeed A (2012) Alkali-activated geopolymers: a literature review. Air Force Research Laboratory, pp 1–99. https://doi.org/10.21236/ada559113
Hassan A, Arif M, Shariq M (2020) Influence of microstructure of geopolymer concrete on its mechanical properties—a review. In: Advances in sustainable construction materials and geotechnical engineering, Lecture Notes in Civil Engineering, pp 119–129
Hassan A, Arif M, Shariq M (2019) Development of low carbon binder for sustainable construction as an alternative to conventional cement. In: National conference on advances in structural technologies (CoAST-2019). Springer, Silchar, India
AS 3600 (2009) Australian Standard® concrete structures AS 3600, Australia
ACI 318-14 (2014) Building code requirements for structural concrete and commentary. American Concrete Institute, Farmington Hills, MI, USA
Diaz-Loya, Allouche F, Vaidya S (2011) Mechanical properties of fly-ash-based geopolymer concrete. ACI Mater J 108:300–306. https://doi.org/10.14359/51682495
BIS:383-1970 (1997) Specification for coarse and fine aggregates from natural sources for concrete. Bureau of Indian Standards
Lee NK, Lee HK (2013) Setting and mechanical properties of alkali-activated fly ash/slag concrete manufactured at room temperature. Constr Build Mater 47:1201–1209. https://doi.org/10.1016/j.conbuildmat.2013.05.107
Nath P, Sarker PK (2017) Flexural strength and elastic modulus of ambient-cured blended low-calcium fly ash geopolymer concrete. Constr Build Mater 130:22–31. https://doi.org/10.1016/j.conbuildmat.2016.11.034
IS 456 : 2000 (2000) Bureau of Indian Standards—Plain and reinforced concrete—code and practice, Fourth. New Delhi
ASTM C618–12a, (2010) Standard specification for coal fly ash and raw or calcined natural pozzolan for use. ASTM. https://doi.org/10.1520/C0618
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Hassan, A., Arif, M. & Shariq, M. Effect of curing condition on the mechanical properties of fly ash-based geopolymer concrete. SN Appl. Sci. 1, 1694 (2019). https://doi.org/10.1007/s42452-019-1774-8
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s42452-019-1774-8